Page 2 - I n t r o d u c t i o n
2 I n t r o d u c t i o n Gen’l (Rev. 2/19/2008) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manuala...
Page 3 - TABLE OF CONTENTS; WARNING
I n t r o d u c t i o n 3 12030809 (Rev. 1/2/2007) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY RULES . . . . . . ....
Page 4 - S a f e t y; TRAINING; SAFETY RULES
4 S a f e t y ST500 Snowblower SR (Rev. 1/2/2007) TRAINING Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To lo...
Page 5 - MAINTENANCE
S a f e t y 5 ST500 Snowblower SR (Rev. 1/2/2007) When improperly operated, power unit can roll over or upset. Use of rollover protective structure(ROPS) with seat belt securely fastened will reducethe possibility of injury or death if rollover or upsetoccurs. Never allow riders on power unit or...
Page 6 - S a fe t y; DANG; SHIELD MISSING; SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!
6 S a fe t y 12030809 (Rev. 1/2/2007) 1 - Serial Number Plate KEEP AWAY! To avoid injury from rotating auger, keep hands, feet, and clothing away. 12030480-A DANGER KEEP AWAY! To avoid injury from rotating parts, shut off engine before unclogging discharge chute. 12030487-A DANGER 2 - 12030487A 3 - ...
Page 7 - O p e ra t i o n; OPERATION; IMPORTANT; PRE-OPERATION CHECK LIST; CAUTION
O p e ra t i o n 7 12030809 (Rev. 1/2/2007) OPERATION Keep hands, feet, hair, and clothing away from equipment while engine is running. Stay clear of allmoving parts. Make sure shields and guards are properly installed and in good condition. Replace if damaged. Never place hands or body into d...
Page 8 - O w n e r S e r v i c e; OWNER SERVICE; NOTES
8 O w n e r S e r v i c e 12030809 (Rev. 1/2/2007) OWNER SERVICE The information in this section is written for operatorswho possess basic mechanical skills. If you need help,your dealer has trained service technicians available. For you protection, read and follow all safety informa-tion in this ma...
Page 9 - A s s e m b l y; ASSEMBLY; Snowthrower Set-up Instructions
A s s e m b l y 9 12030809 (Rev. 1/2/2007) ASSEMBLY Snowthrower Set-up Instructions Remove step and replace with the short step includedwith snowthrower. Remove cotter pin on end of steprod and slide out. Install shorter step and replace rodand cotter pin. Slide lever mount (27) and lift mount (28) ...
Page 10 - Storage; CLEANING
1 0 A s s e m b l y 12030809 (Rev. 1/2/2007) Storage Do not operate power unit with attachment remov ed. A ttachment is require d for power unitstability. Wood blocks can be used to support the rear of thesnowthrower deck when not attached to the tractor.Raise snowthrower deck to it's highest heig...
Page 12 - P a rts; ST500 SNOWTHROWER MAIN ASSEMBLY
1 2 P a rts 12030809 (Rev. 1/2/2007) ST500 SNOWTHROWER MAIN ASSEMBLY 58 7 4 4 53 9 10 33 32 33 31 13 17 14 43 15 42 16 8 35 35 34 12 44 23 18 40 19 21 20 41 22 46 44 57 36 26 36 30 55 56 28 29 27 37 38 39 24 30 35 35 34 1 5 6 8 59 60 69 59 55 54 57 61 62 63 47 73 70 74 53 75 72 73 60 71 52 53 67 11 ...
Page 13 - P a r ts
P a r ts 1 3 12030809 (Rev. 1/2/2007) ST500 SNOWTHROWER MAIN ASSEMBLY REF PART QTY DESCRIPTION 1 72320 1 Auger housing 2 12020152 1 Upper spout 3 12020145 1 Spout deflector 4 70454 2 Thumbscrew, 5/16 - female 5 70455 1 Spout handle 6 12020240 1 Spout lock rod 7 70388 1 Compression spring, 3/4 x .08 ...
Page 14 - A p p e n d i x; BOLT TORQUE CHART
1 4 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...
Page 15 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM
A p p e n d i x 1 5 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............
Page 16 - LIMITED WARRANTY; Zero-Turn Mowers and Woods Boundary
F-8045 MM & Boundary (Rev. 12/1/2008) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Inf...
Page 17 - Zero-Turn Mower and; Utility Vehicle Replacement Parts)
F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006) LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mower and Woods Boundary TM Utility Vehicle Replacement Parts) Woods Equipment Company (“WOODS”) warrants replacement parts for Mow’n Machine TM zero-turn mowers and attachments and Woods Boundary TM ...