Woods MX61 - Manual - manualsarea.com

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n Gen’l (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manuala...

Page 3 - TABLE OF CONTENTS; WARNING

I n t r o d u c t i o n 3 MAN0258 (Rev. 12/14/2007) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 GENERAL INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SAFETY RULES . . . . . . ...

Page 4 - S a f e t y; TRAINING; SAFETY RULES

4 S a f e t y Mow’n Machine Vacuum (10/8/2004) TRAINING Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locat...

Page 5 - TRANSPORTATION

S a f e t y 5 Mow’n Machine Vacuum (10/8/2004) Keep children out of the mowing area and under the watchful care of a responsible adult other thanthe operator. Be alert and turn machine off if a child enters the mowing area. Before attempting to unplug vacuum hoses, dis- engage PTO, stop power ...

Page 6 - SHIELD MISSING; Use a clean, damp cloth to clean safety decals.; SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!

6 S a f e t y MAN0258 (Rev. 12/14/2007) 2 - SERIAL NUMBER PLATE SHIELD MISSING DO NOT OPERATE -- PUT SHIELD ON DANGER 18869 3 - PN 18869 1 - PN 72672 THROWN OBJECT HAZARD CAN RESULT IN SERIOUS INJURY OR DEATH. NEVER OPERATE WITHOUT DISCHARGE CHUTE OR ENTIRE GRASSCATCHER SYSTEM IN PLACE. WARNING 7267...

Page 7 - I n s ta l l a t i o n; VACUUM INSTALLATION; REMOVE DISCHARGE CHUTE; ATTACH HOSE ADAPTER; INSTALL VACUUM HOUSING

I n s ta l l a t i o n 7 MAN0258 (Rev. 12/14/2007) VACUUM INSTALLATION REMOVE DISCHARGE CHUTE 1. Remove mower deck discharge chute and hingeby removing two carriage bolts (2) and nuts (3) andlifting the chute (1) away from the deck. 2. Place the discharge chute and hinge on the chuteadapter (4) and ...

Page 8 - Remove Vacuum Housing; INSTALL BEARING MOUNT ASSEMBLY; Install Bearing Mount

8 I n s ta l l a t i o n MAN0258 (Rev. 12/14/2007) 4. Rotate vacuum housing assembly into place sothat the clevis shaft on vacuum housing assemblyslips inside vacuum front mount (38). 5. Install lynch pin (62) to lock the housing into place. NOTE: If necessary, adjust the position of the vacuum fron...

Page 9 - INSTALL VACUUM DRIVE BELT; INSTALL BELT SHIELD

I n s ta l l a t i o n 9 MAN0258 (Rev. 12/14/2007) 6. Install two cage nuts (63) into slots on deck. 7. Install three new 5/16 x 3/4 whiz bolts (33) into the5/16 cage. NOTE: The nylon flex coupler should move freely up and down between the two flex coupler hubs. 8. Maintain alignment between the two...

Page 10 - DEALER CHECK LIST; PRE-DELIVER CHECK LIST

1 0 I n s ta l l a t i o n MAN0258 (Rev. 12/14/2007) Figure 9 . Belt Shield Installation DEALER CHECK LIST PRE-DELIVER CHECK LIST Inspect the equipment thoroughly after assembly tomake sure it is properly set up before delivering it to thecustomer. The following check lists are a reminder of points ...

Page 11 - S e r v i c e; SERVICE; REPLACE VACUUM HOUSING BEARINGS; REPLACE VACUUM SPINDLE BEARINGS

S e r v i c e 11 MAN0258 (Rev. 12/14/2007) SERVICE REPLACE VACUUM HOUSING BEARINGS 1. Remove vacuum housing (1) from deck. 2. Remove hose adapter (2) from vacuum housing. 3. Remove belt sheave and hardware shown inposition (A) from assembly. 4. Remove housing top (5) from vacuum housing. 5. Remove s...

Page 12 - P a rts; VACUUM & DRIVE ASSEMBLY

1 2 P a rts MAN0258 (Rev. 12/14/2007) VACUUM & DRIVE ASSEMBLY

Page 13 - P a r ts; VACUUM & DRIVE ASSEMBLY PARTS LIST

P a r ts 1 3 MAN0258 (Rev. 12/14/2007) VACUUM & DRIVE ASSEMBLY PARTS LIST REF PART QTY DESCRIPTION 1 75112 1 Vacuum fan housing 2 70570 1 Hose adapter 3 70067 6 1/4 NC x 1/2 Whiz bolt, truss head 4 70065 6 1/4 NC Whiz nut 5 75123 1 Vacuum top 6 75154 1 Vacuum fan 7 64518 * 1 3/8 NF x 1 Hex head ...

Page 14 - A p p e n d i x; BOLT TORQUE CHART

1 4 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

Page 15 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

A p p e n d i x 1 5 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

Page 16 - LIMITED WARRANTY; Zero-Turn Mower and; Utility Vehicle Replacement Parts)

F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mower and Woods Boundary TM Utility Vehicle Replac...

Page 17 - Zero-Turn Mowers and Woods Boundary

F-8045 MM & Boundary (Rev. 10/10/2007) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter In...

Woods MX61 - Manual

Table of Contents:

Summary

Other Woods Models