Woods MAN0115 - Manual - manualsarea.com

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n Gen’l (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manuala...

Page 3 - A s s e m b l y; HOPPER ASSEMBLY; ASSEMBLE HOPPER; Si no lee Ingles, pida ayuda a; WARNING

A s s e m b l y 3 MAN0115 (Rev. 3/31/2006) HOPPER ASSEMBLY ASSEMBLE HOPPER Only use grass collection system with dual tail- wheel option. Figure 1 . Hopper Assembly Assembly of hopper will be easier if assembled upsidedown on a flat surface, see Figure 2. Note that Figure 1shows hopper in the upri...

Page 4 - A s se mb l y; INSTALL CROSSMEMBERS; INSTALL DOOR

4 A s se mb l y MAN0115 (Rev. 3/31/2006) INSTALL CROSSMEMBERS Figure 3 . Side Panel & Front Crossmember Installed Figure 4 . Crossmember Installation NOTE: Hopper should still be upside down. Do not tighten hardware. 1. Install front crossmember (16) between right andleft side panels. Install cr...

Page 5 - INSTALL DOOR HANDLE; INSTALL LINKAGE

A s s e m b l y 5 MAN0115 (Rev. 3/31/2006) 5. Torque all hardware according to page 8. Figure 6 . Door Assembly INSTALL DOOR HANDLE NOTE: Turn hopper assembly over and support in upright position. 1. Attach door handle (29) to left door handle mountas shown in Figure 7. 2. Install stop lever (49) an...

Page 6 - INSTALL HOPPER SUPPORTS

6 A s se mb l y MAN0115 (Rev. 3/31/2006) Figure 8 . Right Side INSTALL HOPPER SUPPORTS 1. Remove two center 3/8 NC x 3/4 hex washer headcap screws from both right and left side of hoodassembly. Note: Drill completely through hood frame if not already done. 2. Attach left hopper support (2) to hood a...

Page 7 - MOUNT HOPPER ASSEMBLY

A s s e m b l y 7 MAN0115 (Rev. 3/31/2006) INSTALL REAR HOPPER SUPPORT &REAR HOPPER PIVOT 1. Attach rear hopper support (3) to the rear of thepower unit using four flanged head cap screws (8),standard flat washers (9), and two flange lock nuts(7) as shown in Figure 11. 2. Attach the rear hopper ...

Page 8 - SECURE HOPPER

8 A s se mb l y MAN0115 (Rev. 3/31/2006) SECURE HOPPER 1. Rotate hopper onto right and left hopper supports. 2. Insert 3/8 lynch pins (18) to attach front hoppercrossmember to support brace as shown in Figure14. Figure 14 . Latch Locked into Position POSITION HOOD FOR SERVICING ENGINE To flip hood u...

Page 9 - P a r ts; MOUNT ASSEMBLY

P a r ts 9 MAN0115 (Rev.3/31/2006) MOUNT ASSEMBLY REF PARTS QTY DESCRIPTION 1 74082 1 Right hopper support 2 74083 1 Left hopper support 3 73677 1 Rear hopper support 4 73678 1 Rear hopper pivot 5 74084 1 Hopper cross brace 6 920 4 3/8 NC x 1-3/4 Cap screw GR5 7 15030 12 3/8 NC Flange lock nut 8 621...

Page 11 - P a rts; HOPPER ASSEMBLY PART LIST

P a rts 11 MAN0115 (Rev.3/31/2006) HOPPER ASSEMBLY PART LIST REF PARTS QTY DESCRIPTION 1 70521 1 Hopper top 2 70504 1 Window 3 70505 2 Mounting bracket 4 70067 68 1/4 NC x 1/2 Whiz bolt 5 70065 82 1/4 NC Whiz nut 6 1000664 1 Right side panel 7 1000665 1 Left side panel 8 70528 1 Upper front panel 9 ...

Page 12 - A p p e n d i x; BOLT TORQUE CHART

1 2 A p p e n d i x Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual ...

Page 13 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

A p p e n d i x 1 3 Bolt Torque & Size Charts (Rev. 10/10/2005) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG ............................................................. Agriculture ATF ...............

Page 14 - LIMITED WARRANTY; Zero-Turn Mower and; Utility Vehicle Replacement Parts)

F-8495 MM & Boundary Repair Parts (Rev. 2/15/2006) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mower and Woods Boundary TM Utility Vehicle Replac...

Page 15 - Zero-Turn Mowers and Woods Boundary

F-8045 MM & Boundary (Rev. 7/6/2007) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com LIMITED WARRANTY (Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Info...

Woods MAN0115 - Manual

Table of Contents:

Summary

Other Woods Models