Page 2 - I n t r o d u c t i o n
2 I n t r o d u c t i o n Gen’l (Rev. 2/19/2008) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manuala...
Page 3 - TABLE OF CONTENTS
I n t r o d u c t i o n 3 MAN0561 (8/25/2006) TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 GENERAL INFORMATION . ...
Page 4 - SPECIFICATIONS
4 I n t r o d u c t i o n MAN0561 (8/25/2006) SPECIFICATIONS GENERAL INFORMATION BSE4 BSE5 RBE4 RBE5 Overall Width 48" 60" 48" 60" Weight 309 lbs. 351 lbs. 164 lbs. 180 lbs. Cutting Edge 3/8 x 3" Welded 3/8 x 3" Welded 3/8 x 3" Welded 3/8 x 3" Welded Moldboard Thickne...
Page 5 - S a f e t y; TRAINING; SAFETY RULES
S a f e t y 5 Heritage Landscape (8/8/2006) TRAINING Safety instructions are important! Read all a t ta c h m e n t a n d p o w e r u n i t m a n u a l s ; f o l l o w a l lsafety rules and safety decal information. (Replace-ment manuals and safety decals are available fromyour dealer. To locate y...
Page 6 - MAINTENANCE
6 S a f e t y Heritage Landscape. (8/8/2006) (Safety Rules continued from previous page) Always sit in power unit seat when operating controls or starting engine. Securely fasten seatbelt, place transmission in neutral, engage brake,a n d e n s u r e a l l o t h e r c o n t r o l s a r e d i s e n...
Page 7 - S a f e ty; - Serial Number Plate; Use a clean, damp cloth to clean safety decals.; WARNING; RBE; SAFETY & INSTRUCTIONAL DECALS; Replace Immediately If Damaged!
S a f e ty 7 MAN0561 (8/25/2006) 1 - Serial Number Plate 2 - 55121 MODEL NO. SERIAL NO. Woods Equipment Company Oregon, Illinois, U.S.A. BE CAREFUL! Use a clean, damp cloth to clean safety decals. Avoid spraying too close to decals when using a pressure washer; high-pressure water can enter through ...
Page 8 - S a fe t y
8 S a fe t y MAN0561 (8/25/2006) SAFETY & INSTRUCTIONAL DECALS ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! Replace Immediately If Damaged! CRUSHING AND PINCHING HAZARD Be extremely careful handling various parts of the machine. They are heavy and hands, fingers, feet, and other body parts ...
Page 9 - O p e r a t i o n; OPERATION; CONNECTING ATTACHMENTS; CAUTION
O p e r a t i o n 9 MAN0561 (8/25/2006) OPERATION The operator is responsible for the safe operation ofthis equipment. The operator must be properly trained.Operators should be familiar with the equipment, thetractor, and all safety practices before starting opera-tion. Read the safety rules and saf...
Page 10 - O p e ra t i o n
1 0 O p e ra t i o n MAN0561 (8/25/2006) Figure 2 . Top Link Connected - Box Scraper Figure 3 . Top Link Connected - Rear Blade OPERATING TECHNIQUES - BOX SCRAPER Adjusting Top Link The box scraper is leveled by adjusting the length ofthe tractor's top link. ● Shortening the top link will deepen the...
Page 12 - M a i n t e n a n c e; BOX SCRAPER; Adjusting or Removing Scarifier Shanks
1 2 M a i n t e n a n c e MAN0561 (8/25/2006) MAINTENANCE The information in this section is written for operatorswho possess basic mechanical skills. If you need help,your dealer has trained service technicians available.For your protection, read and follow the safety informa-tion in this manual. ...
Page 13 - Replacing Scarifier Tooth; CLEANING BOX SCRAPER & REAR BLADE
M a i n t e n a n c e 1 3 MAN0561 (8/25/2006) Replacing Scarifier Tooth 1. Remove scarifier shank (1) from the scarifier bar. 2. Remove the worn tooth by driving a chisel betweenthe shank (1) and tooth (2) . 3. Install replacement tooth and use a punch (3) tobend the locking tab (4) into the retaini...
Page 14 - A s s e m b l y; ASSEMBLY; DEALER SET-UP INSTRUCTIONS
1 4 A s s e m b l y MAN0561 (8/25/2006) ASSEMBLY DEALER SET-UP INSTRUCTIONS Assembly of this Box Scraper and Rear Blade is theresponsibility of the WOODS dealer. It should be deliv-ered to the owner completely assembled and adjustedfor normal conditions. Complete the Check Lists on page 17 before de...
Page 15 - Assemble Box Scraper
A s s e m b l y 1 5 MAN0561 (8/25/2006) Assemble Box Scraper 1. Place the A-frame hitch over the threecorresponding holes on the inside of the scraperframe as shown in Figure 10. 2. Secure the hitch pin (5) with lock washer and nut.Repeat for opposite side. 3. Finish securing the frame by installing...
Page 16 - REAR BLADE
1 6 A s s e m b l y MAN0561 (8/25/2006) REAR BLADE Remove Components from Shipping Configuration 1. Remove nut (5), washer (6) and pull pin (7) fromtop of blade. 2. Remove hitch from the blade. Figure 12 . Shipping Configuration - Rear Blade Assemble Rear Blade 1. Rotate hitch to its upright positio...
Page 17 - D e a l e r C h e c k L i s ts; DEALER CHECK LISTS; PRE-DELIVERY CHECK LIST; DELIVERY CHECK LIST
D e a l e r C h e c k L i s ts 1 7 MAN0561 (8/25/2006) DEALER CHECK LISTS PRE-DELIVERY CHECK LIST (DEALER’S RESPONSIBILITY) Inspect the equipment thoroughly after assembly toensure it is set up properly before delivering it to thecustomer. The following check lists are a reminder of points toinspect...
Page 18 - P a r ts; BSE4 / BSE5 BOX SCRAPER
1 8 P a r ts MAN0561 (8/25/2006) BSE4 / BSE5 BOX SCRAPER 6 8 1 4 2 9 7 10 6 7 12 - COMPLETE DECAL SET 5 REF PART QTY DESCRIPTION 1 1027927 - Top link mount - left hand 2 1027926 - Top link mount - right hand 3 1004635 4/5 Scarifier & tip assembly 4 100181 4/5 1/2 x 3” Bent pin 5 33661 2 Mounting...
Page 19 - RBE4 / RBE5 REAR BLADE; PARKING STAND KIT
P a r ts 1 9 MAN0561 (8/25/2006) RBE4 / RBE5 REAR BLADE 7 1 3 5 6 4 8 - COMPLETE DECAL SET REF PART QTY DESCRIPTION 1 ---------- - Hitch main frame (not sold separately) 2 ---------- - Blade assembly (not sold separately) 3 1022507 1 Plastic cap, 3 x 3” black 4 33661 2 Mounting pin, Cat 1 w/nut &...
Page 20 - A p p e n d i x; BOLT TORQUE CHART
2 0 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...
Page 21 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM
A p p e n d i x 2 1 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............
Page 22 - WARRANTY
F-3079 (Rev 8/26/2008) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Informat...
Page 23 - (Replacement Parts For All Models Except Mow’n Machine
F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...
