Page 2 - NOTE
i i MAN0047 (9/15/00) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the WOODS dealer. Read manual instructionsand safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualare completed before releasing ...
Page 3 - S A F E T Y 1; SAFETY RULES
S A F E T Y 1 BH9000 SFMK (11/1/00) INSTALLATION n This Sub-Frame Mounting Kit is to be used only for the backhoes and tractors specified in the Sub-Frame Mount Installation section of this manual.Any other use or modification of this mounting kitmay result in serious injury or death. n Hydraulics m...
Page 4 - S A F E T Y
2 S A F E T Y BH9000 SFMK (11/1/00) c h e c k a n d c o m p l y w i th t h e s e i n s t r u c t i o n s m a yresult in serious injury or death. n Remove seat and upper support assembly before installing or removing backhoe from tractor.Failure to comply may result in equipment failureand/or persona...
Page 5 - I N S TA L L AT I O N 3; BACKHOE SUB-FRAME INSTALLATION; DANGER
I N S TA L L AT I O N 3 MAN0047 (9/15/00) BACKHOE SUB-FRAME INSTALLATION n The sub-frame mount is designed to provide secure mounting and adequate operator clearancewhen properly installed. Check clearance dimen-s i o n s s h o w n i n f i g u r e 1 t o b e s u r e y o u h a v einstalled sub-frame c...
Page 6 - I N S TA L L AT I O N; SUB-FRAME INSTALLATION; CAUTION
4 I N S TA L L AT I O N MAN0047 (9/15/00) SUB-FRAME INSTALLATION Cont’d n If you do not understand any part of this manual and need assistance, see your dealer. n Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy,rough-soled work shoes and protective...
Page 7 - I N S TA L L AT I O N 5
I N S TA L L AT I O N 5 MAN0047 (9/15/00) SUB-FRAME INSTALLATION Cont’d Install Front Support 1. Remove cap screw (4) and hose holder (5) from bottom of tractor chassis. 2. Install front hanger (1) to bottom of tractor chas- sis and secure using four cap screws (2) and flatwashers (3) as shown in Fi...
Page 8 - I N S TA L L AT I O N
6 I N S TA L L AT I O N MAN0047 (9/15/00) SUB-FRAME INSTALLATION Cont’d Install Right and Left Rear SupportsRight Rear Support #1001380Left Rear Support #100381 1. Install right rear support by inserting cap screw (1) and flat washers (2) into position as shown inFigure 6. NOTE: Install flat washers...
Page 9 - I N S TA L L AT I O N 7
I N S TA L L AT I O N 7 MAN0047 (9/15/00) SUB-FRAME INSTALLATION Cont’d Sub-Frame Fit-Up 1. Center sub-frame under tractor. 2. Insert cross tube of sub-frame into channel of rear support as shown in Figure 8. 3. Install clevis pins (1) and hair pins (2) to secure sub-frame and rear supports as shown...
Page 10 - I N S TA L L AT I O N
8 I N S TA L L AT I O N MAN0047 (9/15/00) SUB-FRAME INSTALLATION Cont’d Attach Sub-Frame to Backhoe 1. Align six holes on the backhoe with holes on sub-frame. 2. Secure with six cap screws, flat washers, and hex nuts as shown. Tighten according to specifica-tions given below. 1. 13759 3/4 NC x 2-1/4...
Page 11 - I N S TA L L AT I O N 9; PUMP KIT INSTALLATION
I N S TA L L AT I O N 9 MAN0047 (9/15/00) PUMP KIT INSTALLATION Install Pump Kit #9504 NOTE: For complete information on pump kit instal-lation, consult the Woods BH9000 backhoe opera-tors manual #38638. NOTE: Discard pump mounting bracket provided inpump kit #9504. 1. Attach pump mounting bracket #...
Page 12 - 0 I N S TA L L AT I O N; WARNING
1 0 I N S TA L L AT I O N MAN0047 (9/15/00) PUMP KIT INSTALLATION Cont. Connect Hydraulic System n Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and...
Page 13 - I N S TA L L AT I O N 11; SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR
I N S TA L L AT I O N 11 MAN0047 (9/15/00) SUB-FRAME & BACKHOE INSTALLATION TO TRACTOR Mount Sub-Frame & Backhoe to Tractor n The sub-frame mount is designed to provide secure mounting and adequate operator clearancewhe n properl y ins ta lled. C he ck clea rance dimen-sions shown in figure ...
Page 14 - 2 I N S TA L L AT I O N
1 2 I N S TA L L AT I O N MAN0047 (9/15/00) SUB-FRAME & BACKHOE to TRACTOR Cont. Attach Top Link 1. Assemble inner top link (2), 1” hex nut (1), and outer top link (3). 2. Attach top link (inner link end) to backhoe main- frame with 1.0 x 4.5 clevis pin (4) and klik pins (5)as shown in Figure 14...
Page 15 - I N S TA L L AT I O N 1 3
I N S TA L L AT I O N 1 3 MAN0047 (9/15/00) SUB-FRAME & BACKHOE to TRACTOR Cont. Remove Backhoe With Sub-Frame n The only time the backhoe may be operated from a po si tion o ther tha n the o pe ra tor se at i s du ri ngbackhoe attachment and removal. Operator must • Read Operator's Manual instr...
Page 16 - 4 I N S TA L L AT I O N; NOTES
1 4 I N S TA L L AT I O N MAN0047 (9/15/00) SUB-FRAME & BACKHOE to TRACTOR Cont. NOTES Store Hydraulic Pump 1. Disconnect pump (1) from tractor PTO. 2. Rotate pump and insert pin on pump mounting bracket through outside hole on foot rest as shownin Figure 16. 3. Secure to foot rest (3) with klik...
Page 18 - 6 A P P E N D I X; BOLT TORQUE CHART
1 6 A P P E N D I X Bolt Torque & Size Charts (Rev. 9/5/00) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual par ...
Page 19 - A P P E N D I X 1 7; BOLT SIZE CHART; ABBREVIATIONS
A P P E N D I X 1 7 Bolt Torque & Size Charts (Rev. 9/5/00) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. 5/16 3/8 1/2 5/8 3/4 7/8 SAE Bolt Thread Sizes MM 25 50 75 100 125 150 175 IN 1 2 3 4 5 6 7 Metric Bolt Thread ...
Page 20 - WARRANTY
F-8494 Effective 3/1/2000 Woods Equipment Company 2606 Illinois Route 2 SouthPost Office Box 1000Oregon, Illinois 61061 815-732-2141 tel815-732-7580 fax WARRANTY (Replacement Parts For All Models Except Mow’n Machines) WEC Company, d/b/a Woods Equipment Company (“WOODS”), warrants this product to be...
