Woods 211822 - Manual - manualsarea.com

Page 2 - I n t r o d u c t i o n; DANGER

2 I n t r o d u c t i o n LMK (Rev. 6/6/2005) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’sManu...

Page 3 - S a f e t y; INSTALLATION; SAFETY RULES

S a f e t y 3 Loader Mounting Kit SR3 (4/25/2003) INSTALLATION This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual.Any other use or modification of this mounting kitmay result in serious injury or death. Hydraulics must be connected as instructed in ...

Page 4 - M o u n t I n s ta l l a t i o n; LOADER MOUNT INSTALLATION; Tractor Preparation; WARNING

4 M o u n t I n s ta l l a t i o n MAN0469 (9/9/2005) LOADER MOUNT INSTALLATION Tractor Preparation ■ Only use 211822 Loader Mounting Kit for mounting Woods 1020/1027 loaders on Massey Ferguson ® 5425, 5435, 5445 or Challenger ® MT425B, MT445B tractors. Any other use or modi-fication of this mountin...

Page 5 - Install Right Rear Mount

M o u n t I n s ta l l a t i o n 5 MAN0469 (9/9/2005) Install Right Rear Mount 1. Using a lifting device, place right mount (1)between cab support bracket and the tractorhousing. Align holes and install tractor hardwarepreviously removed. See Figure 3 2. Use two cap screws (5) and hardened flatwashe...

Page 6 - Install Left Rear Mount

6 M o u n t I n s ta l l a t i o n MAN0469 (9/9/2005) Install Left Rear Mount 1. Using a lifting device, place left mount (2)between cab support bracket and the tractorhousing. Align holes and install tractor hardwarepreviously removed. NOTE: Make sure fuel tank is moved out of the way to allow acce...

Page 7 - Torque Hardware

M o u n t I n s ta l l a t i o n 7 MAN0469 (9/9/2005) Torque Hardware Torque hardware to specifications listed below. Slide fuel tank back into position and secure. Install Grill Guard (Optional) 1. Install grill guard bracket (10) to the right side oftractor frame in the lower set of holes using tw...

Page 8 - Install Oscillation Stops

8 M o u n t I n s ta l l a t i o n MAN0469 (9/9/2005) Install Oscillation Stops 1. Locate the oscillation stops on left and right sidesof the front axle. 2. Remove oscillation stop, place two washers (6)between stop and mounting pad, and replaceoscillation stop. 3. Secure using tractor hardware. 4. ...

Page 9 - H y d r a u l i c I n s ta l l a t i o n; General Description

H y d r a u l i c I n s ta l l a t i o n 9 MAN0469 (9/9/2005) 57988 HOSE KIT INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and will c...

Page 10 - Assemble Hoses

1 0 H y d r a u l i c I n s ta l l a t i o n MAN0469 (9/9/2005) Assemble Hoses 1. Attach a 90° elbow (2) and male quick coupler (3)to each loader supply hose (1). See Figure 13. 2. Connect loader supply hoses to loader feedlinesas shown in Figure 14. 1. 53670 Hose, 150" x 3/4 JICM x 3/4 JICM 2. ...

Page 11 - Route Hoses

H y d r a u l i c I n s ta l l a t i o n 11 MAN0469 (9/9/2005) Route Hoses 1. Route hoses along right mount, between cab andtractor exhaust, under cab, and over right rearaxle. See Figure 16 2. Place hoses in hose hanger (4) (Figure 17) andsecure using lock pin (5). 3. Be sure to avoid contact with ...

Page 12 - Verify Control Movements

1 2 H y d r a u l i c I n s ta l l a t i o n MAN0469 (9/9/2005) Verify Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader andslowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses to tractor remotecontrol coup...

Page 13 - P a r ts

P a r ts 1 3 MAN0469 (9/9/2005) 211822 LOADER MOUNTING KIT 211822 LMK Parts 1015430 Grill Guard Kit (Optional) 15 16 14 17 10 10 11 13 12 6 OscillationStop 1 4 8 9 6 5 2 5 6 4 6 6 3 9 7 TractorHardware CD6756 1015430 Grill Guard Kit 211822 Loader Mounting Kit REF PART QTY DESCRIPTION 1 1015400 1 Rig...

Page 15 - A p p e n d i x; BOLT TORQUE CHART

A p p e n d i x 1 5 Bolt Torque & Size Charts (Rev. 8/14/02) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application.Fasteners must always be replaced with the same grade as specified in the manual par...

Page 16 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM; ABBREVIATIONS

1 6 A p p e n d i x Bolt Torque & Size Charts (Rev. 8/14/2002) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. 5/16 3/ 8 1/2 5/ 8 3/4 7/ 8 SAE Bolt Thread Sizes MM 25 50 75 100 125 150 175 IN 1 7 Metric Bolt Thread Size...

Page 17 - WARRANTY

F-3079 (Rev. 6/23/2005) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 815-732-2141 tel815-732-7580 faxwww.WoodsEquipment.com WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information...

Page 18 - (Replacement Parts For All Models Except Mow’n Machine

F-8494 (Rev. 6/23/2005) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 815-732-2141 tel815-732-7580 faxwww.WoodsEquipment.com ©2005 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trade...

Woods 211822 - Manual

Table of Contents:

Summary

Other Woods Models