Woods 111877 - Manual - manualsarea.com

Page 2 - I n t r o d u c t i o n

2 I n t r o d u c t i o n LMK (Rev. 7/20/2007) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Loader Operator’sMan...

Page 3 - S a f e t y; INSTALLATION; Si no lee Ingles, pida ayuda a; SAFETY RULES

S a f e t y 3 Loader Mounting Kit SR3 (4/25/2003) INSTALLATION This Loader Mounting Kit is to be used only for the loaders and tractors specified in this manual.Any other use or modification of this mounting kitmay result in serious injury or death. Hydraulics must be connected as instructed in ...

Page 4 - M o u n t I n s ta l l a t i o n; LOADER MOUNT INSTALLATION; WARNING; CAUTION; TRACTOR PREPARATION

4 M o u n t I n s ta l l a t i o n MAN0064 (Rev. 7/20/2007) LOADER MOUNT INSTALLATION ■ Only use 111877 Loader Mounting Kit for mounting Woods 1020, 1027, LU126 loaders onFord New Holland 2000, 2310, 2600, 2610, 2810,2910, 3000, 3600, 3610, 3910, 4000SU, 4100,4600SU, and 4610SU tractors. Any other u...

Page 5 - Install Right and Left Rear Mounts

M o u n t I n s ta l l a t i o n 5 MAN0064 (Rev. 7/20/2007) Install Right and Left Rear Mounts 1. Attach right rear mount (1) to the tractor clutchhousing using two cap screws (12) and hardenedflat washers (14) in the top holes and two capscrews (16) hardened flat washers (14) in thelower two holes....

Page 6 - Install Front Mount; Install Right and Left Side rails

6 M o u n t I n s ta l l a t i o n MAN0064 (Rev. 7/20/2007) Install Front Mount 1. Insert four (two per side) carriage bolts (13) intoupper holes of front mount prior to attaching totractor. Carriage bolts should be inserted from theinside pointing outward. 2. Attach front support (3) to tractor, us...

Page 7 - Torque Hardware

M o u n t I n s ta l l a t i o n 7 MAN0064 (Rev. 7/20/2007) Install Grill Guard (Optional) Attach grill guard (21) to front mount (3) using four(two per side) cap screw (23), lock washers (25),hardened flat washers (24) and hex nuts (22). Torque hardware to: . . . . . . . . 85 lbs-ft (115 N-m) 3. 10...

Page 8 - NOTES

8 M o u n t I n s ta l l a t i o n MAN0064 (Rev. 7/20/2007) NOTES

Page 9 - H y d r a u l i c I n s ta l l a t i o n; HOSE KIT INSTALLATION; General Description

H y d r a u l i c I n s ta l l a t i o n 9 MAN0064 (Rev. 7/20/2007) HOSE KIT INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and will c...

Page 10 - Route Hydraulic Hoses; Install Hose Hanger

1 0 H y d r a u l i c I n s ta l l a t i o n MAN0064 (Rev. 7/20/2007) 59723 Hose Kit Route Hydraulic Hoses Route hoses along loader mount, under the right sideof the operator’s platform, and over the rear axle. Be sure to avoid contact with 3-point linkage, brakepedals, and other moveable tractor co...

Page 11 - Verify Control Movements

H y d r a u l i c I n s ta l l a t i o n 11 MAN0064 (Rev. 7/20/2007) 57923 Hose Kit Verify Control Movements 1. Mount loader to tractor: Remove mount pins from loader uprights. Align tractor with loader andslowly drive tractor into loader. Shut off tractor. 2. Connect loader feedline hoses to the lo...

Page 12 - Install Adapter Plate

1 2 H y d r a u l i c I n s ta l l a t i o n MAN0064 (Rev. 7/20/2007) 1001420 HOSE KIT General Description These set-up instructions are for operating the1020/1027 loader using a single-lever controlmounted on the right loader upright as shown Figure13. To use this hydraulic connection, hose kit1001...

Page 13 - Install Hoses

H y d r a u l i c I n s ta l l a t i o n 1 3 MAN0064 (Rev. 7/20/2007) 1001420 Hose Kit Install Hoses 1. Attach 90° end of hoses (7) to the IN, OUT andPBY ports of the loader control valve. 2. Locate the fill plug on the top of right rear axleand remove. 3. Install adapter (5) and elbow (6) into open...

Page 14 - Connect Loader Feedline Hoses

1 4 H y d r a u l i c I n s ta l l a t i o n MAN0064 (Rev. 7/20/2007) 1001420 Hose Kit Install Hose Hanger 1. Install hose hanger bracket (8) under platformbetween brake pedals and chassis as shown inFigure 17. 2. Secure with hex head cap screw (10), flatwashers (11), and lock nut (12). 3. Route hos...

Page 21 - P a r ts

P a r ts 2 1 MAN0064 (Rev. 7/20/2007) 111877 LOADER MOUNTING KIT REF PART QTY DESCRIPTION 1 1026490 1 Right rear mount 2 1026491 1 Left rear mount 3 1001642 1 Front mount 4 1026492 1 Right side rail 5 1026493 1 Left side rail 10 230 * 12 5/8 NC Plated Hex nut 12 300517 * 4 3/4 NC x 1-3/4 HHCS GR5 13...

Page 25 - A p p e n d i x; BOLT TORQUE CHART

A p p e n d i x 2 5 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...

Page 26 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM

2 6 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............

Page 27 - WARRANTY

F-3079 (Rev. 3/31/2010) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 USA 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com WARRANTY All Models Except Mow’n Machine TM Zero-Turn Mowers Please Enter Information Below and Save for Future Reference....

Page 28 - (Replacement Parts For All Models Except Mow’n Machine; Zero-Turn Mowers and Woods Boundary

F-8494 (Rev. 6/23/2005) WARRANTY (Replacement Parts For All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Woods Equipment Company (“WOODS”) warrants this product to be free from defect in material andworkmanship for a period of ninety (90) days from the date...

Woods 111877 - Manual

Table of Contents:

Summary

Other Woods Models