Page 2 - I n t r o d u c t i o n
2 I n t r o d u c t i o n SFMK (Rev. 2/20/2008) TO THE DEALER: Assembly and proper installation of this product is the responsibility of the Woods ® dealer. Read manual instructions and safety rules. Make sure all items on the Dealer’s Pre-Delivery and Delivery Check Lists in the Operator’s Manualar...
Page 3 - S a f e t y; SAFETY RULES; Si no lee Ingles, pida ayuda a
S a f e t y 3 4-Point SFMK (Rev. 5/8/2006) SAFETY RULES ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED! This Sub-Frame Mounting Kit is only for the backhoes and tractors specified in the Sub-FrameM o u n t I n s ta l l a t i o n s e c t i o n o f t h i s m a n u a l . A n yother use or modificat...
Page 5 - I n s ta l l a t i o n; BACKHOE SUB-FRAME INSTALLATION; Tractor Preparation; WARNING
I n s ta l l a t i o n 5 MAN0708 (4/11/2008) BACKHOE SUB-FRAME INSTALLATION Tractor Preparation ■ Only use 1022120 4-Point Sub-Frame Mount- ing Kit for mounting Woods BH70-X, BH80-Xbackhoe on New Holland ® T1510, T1520 tractor equipped with Woods LS84, LC96, LC102, 1009,1012 loaders or New Holland 7...
Page 6 - Install Front Mounts
6 I n s ta l l a t i o n MAN0708 (4/11/2008) Install Front Mounts With Woods LS84 Loader Mount Attach front mount (10) to the right loader mountusing two cap screws (32), four hardened flat wash-ers (29) and two hex nuts (23). 10. 1026846 Front mount (LS84 only) 23. 230 5/8 NC Hex nut 29. 57817 5/8 ...
Page 7 - Install ROPS Brackets; Install Tractor Brackets
I n s ta l l a t i o n 7 MAN0708 (4/11/2008) Install ROPS Brackets 1. Place ROPS bracket (33) under rear axle andsecure to ROPS using two cap screws (30) andhardened flat washers (28). NOTE: Bracket must be orientated with the "short" side towards the outside of the tractor. 2. Repeat for op...
Page 9 - Install Cross Brace; Install Reinforcement Brackets
I n s ta l l a t i o n 9 MAN0708 (4/11/2008) Install Cross Brace 1. Remove PTO shield. 2. Attach cross brace (6) to rear of tractor using twohex flange screws (20). 3. Attach to right and left tractor brackets using four(two per side) cap screws (26), eight hardenedflat washers (28), and four hex nu...
Page 10 - Torque Mounting Hardware; Attach Backhoe Mounts to Backhoe
1 0 I n s ta l l a t i o n MAN0708 (4/11/2008) Torque Mounting Hardware NOTICE ■ Check torque value of mount hardware after 10 hours of operation and again after every 50hours of operation. Attach Backhoe Mounts to Backhoe 1. Attach right backhoe mount (1) and left backhoemount (2) to backhoe frame....
Page 11 - HYDRAULIC INSTALLATION; Assemble Bulkhead Bracket
I n s ta l l a t i o n 11 MAN0708 (4/11/2008) HYDRAULIC INSTALLATION Keep hands and body away from pressurized lines. Use paper or cardboard, not hands or otherbody parts to check for leaks. Wear safety goggles.Hydraulic fluid under pressure can easily penetrateskin and will cause serious injury o...
Page 12 - Install Hydraulic Block and Fittings; Install Hydraulic Hoses
1 2 I n s ta l l a t i o n MAN0708 (4/11/2008) Install Hydraulic Block and Fittings 1. Locate the hydraulic manifold block on the rightside of the tractor just under the fender (Figure19) and remove the block-off cap. 2. Attach hydraulic block (18) to tractor using newO-rings (14), three cap screws ...
Page 13 - Install Hoses to Backhoe Valve
I n s ta l l a t i o n 1 3 MAN0708 (4/11/2008) Install Bulkhead Adapter on Backhoe Mount 1. Attach bulkhead adapter (1) to crossmemberbetween backhoe brackets. Secure with nut sup-plied with adapter. 2. Attach elbow (10) and female quick coupler (16)to bulkhead adapter as shown in Figure 23. 3. Posi...
Page 14 - Mount Backhoe to Tractor; Check Hydraulic System
1 4 I n s ta l l a t i o n MAN0708 (4/11/2008) Mount Backhoe to Tractor This mounting kit is designed to provide sec ure mounting and a de qua te operator clea r-ance for most operators when properly installed.Check clearance dimensions shown below to besure you have installed seat bracket correct...
Page 16 - Remove Backhoe from Tractor
1 6 I n s ta l l a t i o n MAN0708 (4/11/2008) Remove Backhoe from Tractor The only time the backhoe may be operated from a position other than the operator seat i sduring backhoe attachment and removal. Opera-tor must: • Read Mounting Kit Manual instructions ona t ta c h i n g a n d r e m o v i n...
Page 17 - STORAGE
I n s ta l l a t i o n 1 7 MAN0708 (4/11/2008) STORAGE Connect Hydraulic Hoses TRACTOR: Connect male quick coupler on end of hose to female quick coupler at bulkhead bracketwhen backhoe is removed from tractor. See Figure28. NOTICE ■ Failure to connect hoses together will result in damage to tractor...
Page 18 - P a r ts; ARNING; PINCH POINT
1 8 P a r ts MAN00708 (4/11/2008) 1022120 4-POINT SUB-FRAME MOUNTING KIT W ARNING PINCH POINT Keep hands clear . 1006885 1 4 - PN 100 688 5 MODE L NO. S E R IAL NO. W oods Equipment Company Oregon, Illinois, U.S.A. Se rial Nu mb er Pla te
Page 21 - A p p e n d i x; BOLT TORQUE CHART
A p p e n d i x 2 1 Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT TORQUE CHART Always tighten hardware to these values unless a different torque value or tightening procedure is listed for a specific application. Fasteners must always be replaced with the same grade as specified in the manual ...
Page 22 - BOLT SIZE CHART; SAE Bolt Thread Sizes; MM
2 2 A p p e n d i x Bolt Torque & Size Charts (Rev. 3/28/2007) BOLT SIZE CHART NOTE: Chart shows bolt thread sizes and corresponding head (wrench) sizes for standard SAE and metric bolts. ABBREVIATIONS AG .............................................................. Agriculture ASABE .............
Page 23 - WARRANTY
F-3079 (Rev. 4/4/2008) WARRANTY (All Models Except Mow’n Machine TM Zero-Turn Mowers and Woods Boundary TM Utility Vehicles) Please Enter Information Below and Save for Future Reference. Date Purchased: ____________________________ From (Dealer): ___________________________________________ Model Num...
Page 24 - (Replacement Parts For All Models Except Mow’n Machine
F-8494 (Rev. 6/23/2005) Woods Equipment Company 2606 South Illinois Route 2 Post Office Box 1000Oregon, Illinois 61061 800-319-6637 tel800-399-6637 faxwww.WoodsEquipment.com ©2008 Woods Equipment Company. All rights reserved. WOODS, the Woods logo, and "Tested. Proven. Unbeatable." are trade...