Windsor P1700120 - Manual

SUPREME ULTRA

HIGH SPEED

BURNISHER

P

SERVICE MANUAL

AND PARTS LIST

INSPECTION

Carefully unpack and inspect your ma-
chine for shipping damage. Each unit is
operated and thoroughly inspected before

shipment, and any damage is the re-

sponsibility of the delivering carrier who

should be notified immediately.

ELECTRICAL

This rotary polisher is designed to oper-

ate on a standard 15 amp, 115 volt,

hz,

AC household current. Check that the
voltage shown on the serial number plate

is suitable for the supply available. Volt-

ages below

volts or above

125

volts

could cause damage

to

the motor.

WARNING:

To avoid electric shock do

not expose t o rain. Store indoors.

GROUNDING INSTRUCTIONS

To protect the operator from electrical

shock, this machine must be grounded
while in use. The machine is equipped

w i t h an approved, three-conductor

power cord and three-prong grounding

type plug

to

fit the proper grounding

type receptacle. The

is

ped with a

foot power cord.

OPERATION

1. Plug machine into the power supply

and check that the red indicator light

(located on top of switch housing)

i s

on.

2

You will notice three control levers

located at the top of the handle. The

two smaller ones directly beneath

the handle grips control the o n l o f f

switches. From the operator's posi-
tion, the longer lever on the right is

used for

the handle

in position.'

3.

With the handle locked in the upright

position, tilt the machine back until

the handle is resting on the floor ex-

posing the

drive-pad. Install

the proper high speed buffing pad
u s i n g the

p a d

holder to retain pad.

4. With the pad properly installed, return

machine

to

the upright position.

CAUTION: To prevent possible dam-

age t o the pad or pad driver, remove
buffing pad from machine when not
in use.

5. Adjust front caster: For

pads

turn caster adjusting knob counter-

c l o c k w i s e t o l o w e r machine. For
thick pads turn clockwise t o raise

machine.

NOTE:

When pad pressure is properly

set, the machine will start instantly.
It too much pressure i s

an

overload of motor will
circuit breaker

to

trip.

6.

Pull up on the adjusting lever and
lower the handle t o a comfortable

working height. Release adjusting

lever

to

lock

handle

in

place.

NOTE:

A safety switch mounted

in

the handle w i l l not allow machine

to

run until handle is lowered

t o

the

operating position.

For best results, the Supreme

Speed Burnisher should be operated

a straight line

-

forward and re-

verse

-

not side

to

side as you would

a

low speed polisher.

The floor polisher is equipped with a

circuit breaker. The action of the cir-
cuit breaker i s entirely dependent

upon the loading of the brush drive

motor and will only trip under exces-

sive overload conditions. If the circuit

breaker should trip, i t can be reset

after

20

seconds by pressing the re-

set button on the right hand side of
the motor housing.

NOTE:

The operator should correct

the cause of overloading before pro-
ceeding. The most common cause i s
an excessively s o i l e d p a d w h i c h
should be

over, cleaned

or

re-

placed.

SERVICING

A full service inspection involves the

in-

spection and testing of all items which
affect operator safety, items which may
require adjustment from time

to

time,

and items subject t o wear which may

require replacement in order to prevent

a

breakdown.

Motor:

The motor is totally enclosed,

capacitor start, capacitor run with circuit
breaker protection.

A l l

ball bearings are

and have

enough l u b r i c a n t f o r the l i f e of t h e

machine.

Remove motor cover occasionally and

blow dust and lint from motor housing.

Wheels: Periodically remove wheels and

add silicone lubricant to axle.

Motor

Removal:

1.

Remove high-flex drive pad

(4)

screws.

2.

Remove brush cover

(6)

screws.

3.

Release tension on belt tension spring.

4. Remove motor mounting bolts

(3).

1. Remove high-flex drive pad.

2. Remove brush cover.

3.

Release tension on

belt

tension spring.

4. Loosen nuts on motor mounting studs

- 4

or

5

turns.

5.

I n s t a l l new belt and readjust belt

tension as shown:

The trouble shooting guides on inside

and back cover have been categorized

to

assist you

in

locating and servicing

problems that could occur during the
l i f e of the

Burnisher.