Windsor D250 (115V) - Manual

Page 2 - TABLE OF CONTENTS; Warranty; INSPECTION

TABLE OF CONTENTS D-250 98828 04/08/03 1 Data Log/Table of Contents ...............1 Safety Instructions .............................2 Grounding Instructions .......................3 Operations ..........................................4 Maintenance ………………………….6-7 Troubleshooting......................

Page 3 - SAFETY INSTRUCTIONS; IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS

SAFETY INSTRUCTIONS D-250 98828 11/09/00 2 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. This machine is for commercial use. To reduce the risk of fire, electric sh...

Page 4 - GROUNDING INSTRUCTIONS; GROUNDING INSTRUCTIONS:

GROUNDING INSTRUCTIONS D-250 98828 04/25/02 3 THIS PRODUCT IS FOR COMMERCIAL USE ONLY. ELECTRICAL: The amp, hertz, and voltage are listed on thedata label found on each machine. Usingvoltages above or below those indicated on thedata label will cause serious damage to themotors. GROUNDING INSTRUCTIO...

Page 5 - OPERATIONS; GENERAL INFORMATION:; , flush the system with a neutralizing; For hose fitting lubrication; silicone lubricant which will not damage o-rings.; PRIMING THE PUMP

OPERATIONS D-250 98828 04/08/03 4 CARPET INSPECTION: Determine precisely what areas you are going toclean. Note problem areas in the carpet or tackstrip. Look for loose carpet, heavily damaged areas,discolored stains, or grease spots that will requireprespotting. Note the carpet type. Check theavail...

Page 6 - OPERATION; HEATER OPERATION; SHUT DOWN AND STORAGE

OPERATION D-250 98828 04/08/03 5 HEATER OPERATION The disconnect fittings on theheater will become extremely hot during operation. Allow sufficient time tocool, or run solution through the machine withthe heater turned off before disconnecting the orperforming any maintenance on the heater. Before d...

Page 7 - MAINTENANCE; PERIODIC MAINTENANCE; MONTHLY MAINTENANCE; LUBRICATION

MAINTENANCE D-250 98828 04/08/03 6 DAILY MAINTENANCE: (At the end of each working day ) :1.) Flush the entire system, including floor tool,hand tool, etc., with 1 to 3 gallons of clean,hot water. 2.) Vacuum out the solution tank . 3.) Rinse tank with fresh water. Periodicallyinspect the recovery tan...

Page 9 - VACUUM MOTOR REPLACEMENT

MAINTENANCE D-250 98828 04/08/03 8 ! WARNING: ONLY QUALIFIED MAINTENANCE PERSONNEL ARE TO PERFORMTHE FOLLOWING REPAIRS. VACUUM MOTOR REPLACEMENT 1. Turn off all switches and unplug machine. 2. Remove recovery tank. 3. Locate the vacuum motor wires and disconnect at the connector. 4. Remove the vacuu...

Page 10 - MAINTENANCE & TROUBLESHOOTING; D-250 PUMP MAINTENANCE

MAINTENANCE & TROUBLESHOOTING D-250 98828 04/08/03 9 D-250 PUMP MAINTENANCE Per manufacturer’s recommendations the following maintenance should be performedutilizing noted kits:1.) 500 hours-Kit 55250751 replaces the V-packing, wave washer, packing spreader and plunger guide. 2.) 500 hours-Kit 5...

Page 11 - POWER TYPE; ELECTRIC VACUUM MOTOR:; GENERAL DIMENSIONS/WEIGHT

TROUBLESHOOTING CONT. D-250 98828 04/08/03 10 Solution hose Corrosion on fittings Clean with steel wool. fitting hard to Soak in acetic acid (white vinegar). connect Lubricate lightly with silicone baselubricant. Carpet not Severe soil conditions Make several passes at right angles to getting clean....

Page 13 - THIS PAGE LEFT BLANK INTENTIONALLY

D-250 98828 04/08/03 12 THIS PAGE LEFT BLANK INTENTIONALLY

Page 14 - RECOVERY TANK ASSEMBLY

RECOVERY TANK ASSEMBLY D-250 98828 06/07/03 13 20 21 14 17 18 19 36 16 13 15 9 12 11 10 35 8 34 7 4 6 5 2 3 1 22 23 24 25 13 13 29 27 28 26 30 31 32 33

Page 16 - SOLUTION TANK ASSEMBLY

SOLUTION TANK ASSEMBLY D-250 98828 06/07/03 15 12A 39 44 42 15 18 19 40 41 20 21 22 14 17 16 13 54 45 46 43 31 47 51 76 48 49 52 35 23 8 37 38 36 26A 27 30 28 24 25 31 34 29 33 32 11 10 31 9 8 7 6 5 1 41 55 50 46 53 38 8 57 56 60 72 73 71 69 70 58 8 38 38 59 61 64 74 63 66 65 62 68 3 2 4 67 63

Page 18 - SUGGESTED SPARE PARTS; DESCRIPTION

SOLUTION TANK ASSEMBLY CONT'. D-250 98828 06/07/03 17 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 54 70232 2 SCR, 10-32 X 3/8 FHMS SS 55 57196 2 NUT, 1/2 PUSH-ON DOME CAP 56 040-06 1 WHEEL 8” BLK CENTERED HUB 57 010-01 1 AXLE ASM, LEFT 58 065-28 2 DIAMONDBACK 200 PUMP SUPPORT 59 040-03 1 CAS...

Page 19 - Limited Warranty

Windsor Industries reserves the right to change its warranty policy without notice – Rev2 10/16/02 1 WINDSOR INDUSTRIES New Machine Warranty Limited Warranty Windsor Industries, Inc. warrants new machines against defects in material and workmanship under normal use and service to theoriginal purchas...

Page 20 - 0 Day Warranty Extension Available

Windsor Industries reserves the right to change its warranty policy without notice – Rev2 10/16/02 2 WINDSOR INDUSTRIES New Machine Warranty 90 Day Warranty Extension Available Upon receipt of the Machine Registration Card, Windsor will extend by 90 days, from the date of purchase, all items include...

Windsor D250 (115V) - Manual

Table of Contents:

Summary

Other Windsor Models