Windsor LB2000 - Manual - manualsarea.com

Page 2 - MACHINE DATA LOG/OVERVIEW; YOUR DEALER; MODEL

MACHINE DATA LOG/OVERVIEW LB2000 980088 03/08/03 2 For the name and address of your dealer contact: Windsor Industries YOUR DEALER Name: __________________________________________________________________________________________________ Address: _______________________________________________________...

Page 3 - TABLE OF CONTENTS; Operation

TABLE OF CONTENTS LB2000 980088 03/08/03 3 Machine Data Log/Overview. .........................2 Table of Contents ...........................................3 HOW TO USE THIS MANUAL How to use this Manual. ................................1-1 SAFETY Important Safety Instructions .......................

Page 4 - HOW TO USE THIS MANUAL

HOW TO USE THIS MANUAL LB2000 980088 03/08/03 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. Parts may be ...

Page 5 - IMPORTANT SAFETY INSTRUCTIONS; When using an electrical appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS

LB2000 980088 03/08/03 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only ind oors. Do not use outdoo...

Page 6 - HAZARD INTENSITY LEVEL; WARNING; WARNING; Use Windsor approved replacement parts.; WARNING; CAUTION

HAZARD INTENSITY LEVEL LB2000 980088 03/08/03 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazard intensity ...

Page 8 - TECHNICAL SPECIFICATIONS; ITEM

TECHNICAL SPECIFICATIONS LB2000 980088 03/08/03 3-1 ITEM DIMENSION/CAPACITY Construction Heavy-duty die cast aluminum deck with heavy-duty rubber bumper, tubular steel self adjusting handle with die cast aluminum handle housing. Motor 1.75 hp Transmission Direct drive from motor shaft. Pad speed 200...

Page 9 - HANDLE INSTALLATION

HANDLE INSTALLATION LB2000 980088 03/08/03 3-2 4. Slide Bolt (item 3) thru, washers (item 2), Handle Mount Brackets and Handle Assembly as shown. Tighten bolt (item 3) and nut (item 1) until the handle can not twist in the mount bracket (45 -50 foot pounds). 5. Check handle for movement up and down....

Page 10 - OPERATION

OPERATION LB2000 980088 03/08/03 3-3 ! CAUTION CONTROLS 1. Safety Lock – Prevents unintended operation of the machine. 2. Switch Levers – Turns machine on/off. OPERATION For indoor use only. When using the pad, always keep the machine moving when in contact with the floor. High starting torque. Hold...

Page 11 - MACHINE TROUBLESHOOTING; PROBLEM

MACHINE TROUBLESHOOTING LB2000 980088 03/08/03 4-1 PROBLEM CAUSE SOLUTION Machine will not run Tripped circuit breaker Reset Circuit breaker tripped in building. Check and reset Fuse in motor is blown Replace CAUTION: To reduce the risk of electrical shock, unplug the machine before opening fuse hol...

Page 12 - WIRING DIAGRAM / SERVICE SCHEDULE

WIRING DIAGRAM / SERVICE SCHEDULE LB2000 980088 11/15/03 4-2 SERVICE SCHEDULE MAINTENANCE DAILY MONTHLY Check pad wear to prevent buildup of chemicals * Check pad driver system for damage * Check handles, switches, and knobs for damage * Store with pad off the floor * Check all bearings for noise * ...

Page 13 - THIS PAGE LEFT BLANK INTENTIONALLY

LB2000 980088 03/08/03 4-3 THIS PAGE LEFT BLANK INTENTIONALLY

Page 14 - DECK GROUP

DECK GROUP LB2000 980088 03/08/03 5-1 16 8 1 1 13 14 15 1 2 9 10 6 7 1 4 5 3 2

Page 16 - HANDLE GROUP

HANDLE GROUP LB2000 980088 03/08/03 5-3 16 17 1 2 3 4 5 6 10 7 9 8 11 15 14 13 12

Page 19 - LOWER HANDLE GROUP

LOWER HANDLE GROUP LB2000 980088 03/08/03 5-6 REF PART NO. QTY DESCRIPTION SERIAL NO. FROM NOTES: 1 70738 1 SCR, M5 X .8MM X 10 MM PPHMS BLK 2 20005 1 CLAMP, 5/16 NYLON 3 67468 2 RING, 10MM EXTERNAL SNAP 4 66340 1 PIN, DOWEL 10MM DIA X 124 MM LG 5 140421 1 BRACKET, HANDLE LINK 6 67469 2 RING, 13MM E...

Page 20 - MOTOR GROUP

Page 24 - WIRING GROUP

WIRING GROUP LB2000 980088 11/15/03 5-11 11 8 9 6 2 1 3 4 10 9 8 5 7 12 PRIOR TO SN*

Page 26 - SUGGESTED SPARE PARTS

SUGGESTED SPARE PARTS LB2000 980088 03/08/03 5-13 PART NO. DESCRIPTION SERIAL NO. FROM NOTES: 73990 SPRING, EXT .5 OD X 3.5 L 73993 SPRING, COMP .48 OD X .91 L 72123 SWITCH, 25A SPST 125 -250V SNAP 140401 CIRCUIT BREAKER, 30 AMP 67488 RECTIFIER, 50A 600V BRIDGE 14404 BRUSH SET MOTOR (PKG OF 4) 34378...

Page 27 - Limited Warranty

Windsor Industries reserves the right to change its warranty policy without notice – Rev2 10/16/02 1 WINDSOR INDUSTRIES New Machine Warranty Limited Warranty Windsor Industries, Inc. warrants new machines against defects in material and workmanship under normal use and service to theoriginal purchas...

Page 28 - 0 Day Warranty Extension Available

Windsor Industries reserves the right to change its warranty policy without notice – Rev2 10/16/02 2 WINDSOR INDUSTRIES New Machine Warranty 90 Day Warranty Extension Available Upon receipt of the Machine Registration Card, Windsor will extend by 90 days, from the date of purchase, all items include...

Windsor LB2000 - Manual

Table of Contents:

Summary

Other Windsor Models