Page 2 - MACHINE DATA LOG/OVERVIEW; YOUR DEALER
MACHINE DATA LOG/OVERVIEW CUTTER 36V (SCE) 86037030 02/13/07 2 YOUR DEALER Name: ________________________________________________________________ Address: _____________________________________________________________ Phone Number: ________________________________________________________ OVERVIEW The...
Page 3 - TABLE OF CONTENTS
TABLE OF CONTENTS CUTTER 36V (SCE) 86037030 12/05/06 3 Machine Data Log/Overview. ............................... 2 Table of Contents ................................................. 3 HOW TO USE THIS MANUAL How to use this Manual. ....................................... 1-1 SAFETY Important Safety...
Page 4 - HOW TO USE THIS MANUAL; REF –
HOW TO USE THIS MANUAL CUTTER 36V (SCE) 86037030 12/05/06 1-1 This manual contains the following sections: - HOW TO USE THIS MANUAL - SAFETY - OPERATIONS - MAINTENANCE - PARTS LIST The HOW TO USE THIS MANUAL section will tell you how to find important information for ordering correct repair parts. P...
Page 5 - IMPORTANT SAFETY INSTRUCTIONS; When using an battery powered appliance, basic precaution; READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE.; SAVE THESE INSTRUCTIONS
CUTTER 36V (SCE) 86037030 12/05/06 2-1 IMPORTANT SAFETY INSTRUCTIONS When using an battery powered appliance, basic precaution must always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THIS MACHINE. To reduce the risk of fire, electric shock, or injury: Use only indoors. D...
Page 6 - HAZARD INTENSITY LEVEL; FOR; WARNING; CAUTION; WARNING
HAZARD INTENSITY LEVEL CUTTER 36V (SCE) 86037030 12/05/06 2-2 The following symbols are used throughout this guide as indicated in their descriptions: HAZARD INTENSITY LEVEL There are three levels of hazard intensity identified by signal words - WARNING and CAUTION and FOR SAFETY. The level of hazar...
Page 7 - SAFETY LABEL LOCATION
SAFETY LABEL LOCATION CUTTER 36V (SCE) 86037030 12/05/06 2-3 NOTE: These drawings indicate the location of safety labels on the machine. If at any time the labels become illegible, promptly replace them. 2% GRADE WARNING SEE MANUAL CIRCUIT BREAKER DECAL PN 86243610 PRV NO. 500579 SAFETY DECAL 862525...
Page 8 - TECHNICAL SPECIFICATIONS; ITEM DIMENSION/CAPACITY
TECHNICAL SPECIFICATIONS CUTTER 36V (SCE) 86037030 12/05/06 3-1 ITEM DIMENSION/CAPACITY Nominal power 2160 W Rated Voltage 36 Volt DC Rated Amperage 60 amps Batteries 6 x 6 volt 250-305-335 AH @ 20 Hr rate Scrub Brush Motors 2 x .75 hp (.56 kW) Vacuum Motor 3 Stage .75 hp (.56 kW) Propelling Motor ....
Page 9 - ITEM MEASURE; Height
TECHNICAL SPECIFICATIONS CUTTER 36V (SCE) 86037030 12/05/06 3-2 HEIGHT WIDTH LENGTH ITEM MEASURE Height 46 in (117 cm) Length with 32 in. (81 cm) scrub head 71 in (180) Width without squeegee and scrub head 28 in (71 cm) Width of squeegee for 32 in. (81 cm) scrub head 39 in (99 cm) Width of scrub pa...
Page 10 - HOW THE MACHINE WORKS
HOW THE MACHINE WORKS CUTTER 36V (SCE) 86037030 12/05/06 3-3 The Saber Cutter is a battery powered, self-propelled, hard floor scrubber intended for commercial use. The appliance applies a cleaning solution onto a hard floor, scrubs the floor with brushes, and then vacuums the soiled water back into...
Page 11 - COMPONENTS; Panel
COMPONENTS CUTTER 36V (SCE) 86037030 12/05/06 3-4 1. Control Panel 2. Front Cover 3. Recovery Tank 4. Recovery Tank Drain Hose 5. Scrub Head Shrouds 6. Solution Tank 7. Solution Tank Cover 8. Solution Tank Drain Hose 9. Solution Strainer 10. Squeegee 11. Aqua-Mizer 12. Top Cover 13. Vacuum Motor 14....
Page 12 - CONTROLS
CONTROLS CUTTER 36V (SCE) 86037030 12/05/06 3-5 3 5 1 6 13 2 9 8 15 7 11 10 4 12 14
Page 13 - Knobs
CONTROLS CUTTER 36V (SCE) 86037030 12/05/06 3-6 1. Key Switch 2. Emergency Shut-Off Switch 3. Speed Control Knob 4. Propel Control Lever 5. Reverse Button 6. Brush Switch 7. Brush Lift Lever 8. Solution Control Knobs 9. Vacuum Switch 10. Squeegee Lift Lever 11. Squeegee Pitch Adjustment Knob 12. Squ...
Page 15 - BATTERY CHARGE LEVEL INDICATOR; To set parking brake, push down to lock notch.
CONTROLS CUTTER 36V (SCE) 86037030 12/05/06 3-8 13. BATTERY CHARGE LEVEL INDICATOR Indicates the charge level of the batteries. The meter display is divided into 10 vertical bars. Bar illuminated on the far right indicates full charge. Bars flashing near the left side indicate the batteries should b...
Page 16 - MACHINE OPERATION; PRE-RUN MACHINE INSPECTION
MACHINE OPERATION CUTTER 36V (SCE) 86037030 12/05/06 3-9 PRE-RUN MACHINE INSPECTION Do a pre-run inspection to find possible problems that could cause poor performance or lost time from breakdown. Follow the same procedure each time to avoid missing steps. NOTE: See maintenance section for pre-run m...
Page 18 - EMPTYING AND CLEANING TANKS
MACHINE OPERATION CUTTER 36V (SCE) 86037030 12/05/06 3-11 DOUBLE SCRUB For floors which are heavily soiled or have thick accumulations of floor finish may not clean sufficiently with one pass. In these cases it will be necessary to double scrub. To double scrub, make the first pass over the surface ...
Page 19 - MAINTENANCE; SERVICE SCHEDULE; MAINTENANCE DAILY
MAINTENANCE CUTTER 36V (SCE) 86037030 12/05/06 4-1 SERVICE SCHEDULE MAINTENANCE DAILY WEEKLY MONTHLY 100 HRS 200 HRS Check batteries after charging; add water if necessary * Check pad wear to prevent buildup of chemicals * Check linkages and connectors for wear and damage * Check hoses for wear, blo...
Page 22 - SPECIFIC GRAVITY; BATTERY CONDITION
MAINTENANCE CUTTER 36V (SCE) 86037030 12/05/06 4-4 CHECKING BATTERY SPECIFIC GRAVITY Use a hydrometer to check the battery specific gravity. CHECKING GRAVITY A. Hydrometer B. Battery NOTE: Do not take readings immediately after adding distilled water, if the water and acid are not thoroughly mixed, ...
Page 23 - CHANGING BATTERIES; FRONT OF MACHINE
MAINTENANCE CUTTER 36V (SCE) 86037030 12/05/06 4-5 5. Replace the battery caps, and leave them in place while charging. 6. Unplug the battery connector from the machine. FOR SAFETY: When charging, connect the charger to the batteries before connecting the charger to the AC wall outlet. Never connect...
Page 24 - BLADES; Inspect or repair as necessary and reinstall.; SQUEEGEE DEFLECTION
MAINTENANCE CUTTER 36V (SCE) 86037030 12/05/06 4-6 2. SQUEEGEE BLADES The front squeegee blade allows solution to pass through channels in the blade into the squeegee assembly while maintaining vacuum to provide lift. The front blade has four wear surfaces and can be rotated for extended life. The f...
Page 25 - Remove deck shrouds.; SIDE VIEW OF SQUEEGEE BLADE
MAINTENANCE CUTTER 36V (SCE) 86037030 12/05/06 4-7 TO ADJUST SQUEEGEE PITCH 1. Choose a smooth, level surface. Turn “ON” the key switch. Lower the squeegee and drive forward at least 2 feet (60cm.). 2. With the squeegee down, stop the machine. Do not allow machine to roll back. FOR SAFETY: Before le...
Page 27 - STRAINER; NOTE: Use hand operated grease gun only.
MAINTENANCE CUTTER 36V (SCE) 86037030 12/05/06 4-9 ! WARNING 6. SOLUTION STRAINER The solution strainer is located in front of the left front wheel. The solution strainer protects the solenoid valve from debris. If there is little or no solution flow to the ground, check the strainer for debris. Dra...
Page 28 - MOTOR; Disconnect batteries from machine.; BREAKERS; 5 Amp. Protects the propel
MAINTENANCE CUTTER 36V (SCE) 86037030 12/05/06 4-10 ! WARNING 8. TRACTION MOTOR Do not use a pressure washer to clean around the motors. Use tap pressure only. TRACTION MOTOR CARBON BRUSH REPLACEMENT FOR SAFETY: Before leaving or servicing machine, stop on a level surface, turn off machine and remov...
Page 30 - MACHINE TROUBLESHOOTING; PROBLEM
MACHINE TROUBLESHOOTING CUTTER 36V (SCE) 86037030 12/05/06 4-12 PROBLEM CAUSE SOLUTION Poor or no water pick-up Squeegee out of adjustment Adjust squeegee Debris caught on squeegee Remove debris Worn squeegee blades Rotate or replace squeegee blades Vacuum hose clogged Clear obstruction from hose Va...
