WEN BA3959 - User Manual

GENERAL SAFETY RULES 7. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards. POWER TOOL USE AND CARE 1. Do not force the power tool. Use the correct power tool fo...

SAW BLADE SAFETY 1. Always wear protective gloves when handling saw blades.2. Only use blades with correct size and type for both your band saw and your workpiece.3. Never use damaged or deformed saw blades. Only use sharp blades.4. Install the saw blade in the correct orientation indi- cated in the...

DURING CUTTING OPERATIONS 1. Always stand to one side when operating the saw. Never have any part of the body in line with the path of the saw. Never hold a workpiece in your hand or across your legs while cutting. 2. Ensure hands are away from the cutting area and blade. Keep one hand on the rear h...

ELECTRICAL INFORMATION AMPERAGE REQUIRED GAUGE FOR EXTENSION CORDS 25 ft. 50 ft. 100 ft. 150 ft. 2.8A 18 gauge 16 gauge 16 gauge 14 gauge 3. Check with a licensed electrician or service personnel if you do not completely under- stand the grounding instructions or whether the tool is properly grounde...

Accessories Components UNPACKING & PACKING LIST UNPACKING With the help of a friend or trustworthy foe, such as one of your in-laws, carefully remove the band saw from the packaging and place it on a sturdy, flat surface. Make sure to take out all contents and accessories. Do not discard the pac...

KNOW YOUR BAND SAW TOOL PURPOSE Make continuous and precise cuts with your WEN Band Saw. Refer to the following diagrams to become familiarized with all the parts and controls of your band saw. The components will be referred to later in the manual for assembly and operation instructions. ON/OFF Swi...

ASSEMBLY & ADJUSTMENTS WARNING! Unplug the machine from the power source before assembly and making adjustments. Failure to comply may cause serious injury. Assembly requires at least two people to safely move around the band saw. ASSEMBLING THE TABLE 1. Remove the M6x24 hex bolt, spring washer,...

ASSEMBLY & ADJUSTMENTS WARNING! Always be sure that the tool is switched off and unplugged before making any adjustments. Wear work gloves when handling saw blades. Failure to comply may cause serious injury. SAW BLADE TRACKING Before initial cutting and after every blade change, check and adjus...

ASSEMBLY & ADJUSTMENTS UPPER BLADE GUIDES ADJUSTMENT The upper blade guides need to be readjusted after every blade change or blade tracking adjustment. 1. Upper Thrust Bearing (Fig. 9 - 1): Loosen the upper right screw (Fig. 9 - 2) using the S4 hex wrench to adjust the position of the thrust be...

ASSEMBLY & ADJUSTMENTS CHANGING THE BAND SAW BLADE 1. Remove the M6x24 hex bolt, spring washer, flat washer and wing nut from the work table assembly. 2. Open the upper and lower blade covers (Fig. 13). 3. Set the upper blade guard to its lowest position, minimizing the space between the bottom ...

OPERATION SUGGESTIONS AND WARNINGS: • Do not touch the saw blade when cutting.• During saw operation, wear safety glasses but do not wear gloves.• Cut only one workpiece at a time.• Always hold the workpiece down on the table.• Do not jam any workpieces.• Do not try to slow the blade down by pushing...

BLADE WIDTH 1/8 in. 3/16 in. 1/4 in. 3/8 in. 1/2 in. 3/4 in. 1 in. MINIMUM RADIUS 3/16 in. 5/16 in. 5/8 in. 1-1/2 in. 2-1/2 in. 5-1/2 in. 7 in. OPERATION GENERAL CUTTING NOTE: Before cutting the actual workpiece, it’s best to use a scrap piece of lumber to check the settings and to get the feel of o...

WARRANTY STATEMENT WEN Products is committed to building tools that are dependable for years. Our warranties are consistent with this commitment and our dedication to quality. LIMITED WARRANTY OF WEN PRODUCTS FOR HOME USE GREAT LAKES TECHNOLOGIES, LLC (“Seller”) warrants to the original purchaser on...