Weber 2 - Manual

Weber 2

Weber 2 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
Page: / 8

Table of Contents:

  • Page 2 – Apply pipe sealant to only the area indicated. Figure 5.; WARNING: Use a pipe sealant compound on the; MODELS WITH A BLACK SQUARE PIPE PLUG:; SIDE BURNER GAS CONNECTIONS; MODELS WITH A BRASS CAP:; Figure 4; OR
  • Page 3 – Figure 8; CHECK FOR GAS LEAKS; DANGER; Figure 9
  • Page 4 – Lighting the Side Burner; ) Check that the fuel scale reads more than E.; Secure side burner; CAUTION: Make sure both locks have snapped into
  • Page 6 – Side Burner Troubleshooting; Is fuel hose bent or kinked?
  • Page 7 – Side Burner Maintenance; WARNING: All gas controls and supply valves should
Loading the manual

Genesis

™

Side Burner

Accessory Installation

Step 1

몇

WARNING: All gas controls and supply valves

should be in the OFF position.

You will need: Side burner assembly (includes burner
grate), side burner lock, pipe sealant (suitable for natural
or LP gas), 1/4, 7/16, 5/8, 3/4 and 11/16 inch open-end or
two adjustable wrenches.

Step 2

Genesis 2 and 2000 Models:

Remove the right side work table, burner control knobs
and control panel.

Genesis 4 Models:

Remove the right side work table, serving tray, burner
control knobs, FlameCheck Safety button and control panel.

For use with Genesis Gas Barbecues Only

27-4736910 3/98

Step 3

Note: Your owner’s manual may reflect installing only
one side burner lock. If it does, please ignore and
follow this installation procedure for two side burner
locks.

You will need: frame assembly, two side burner locks and
a 7/16 inch wrench.

Loosen the right rear 1/4 x 20 bolt. Install the side burner
lock. The “U” shape cut out of the lock slips down over the
bolt. Tighten with a wrench. Figure 1 (a).

Loosen the right front 1/4 x 20 bolt. The side burner lock
fits between the front panel and the frame. The “U” shape
cut out slips up over the bolt. Tighten with a wrench.
Figure 1 (b).

Figure 1

(a)

(b)

Follow the remainder of assembly steps in your Owners
Manual.

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - Apply pipe sealant to only the area indicated. Figure 5.; WARNING: Use a pipe sealant compound on the; MODELS WITH A BLACK SQUARE PIPE PLUG:; SIDE BURNER GAS CONNECTIONS; MODELS WITH A BRASS CAP:; Figure 4; OR

2 Step 5 FOR MODELS THAT USE THE ENCLOSEDBRASS FITTING Apply pipe sealant to only the area indicated. Figure 5. 몇 WARNING: Use a pipe sealant compound on the threads that is approved for natural or LP gas. Screw the fitting into the manifold using the 5/8 inch wrench.Figure 6(a). Only use pipesealan...

Page 3 - Figure 8; CHECK FOR GAS LEAKS; DANGER; Figure 9

3 Figure 8 Step 7 CHECK FOR GAS LEAKS Remove the control knob and two screws holding the sideburner cover to the bottom. Figure 8. Figure 7(a) Step 6 Slide the side burner assembly into the open end of theright frame. Route the side burner hose so that it parallelsthe front of the barbecue. Loop the...

Page 4 - Lighting the Side Burner; ) Check that the fuel scale reads more than E.; Secure side burner; CAUTION: Make sure both locks have snapped into

4 몇 DANGER Failure to open lid while igniting the sideburner, or not waiting 5 minutes to allow gasto clear if the side burner does not light,may result in an explosive flame-up whichcan cause serious bodily injury or death. Lighting the Side Burner The side burner has a separate ignition system fro...

Other Weber Models

All Weber Other