Wagner F230 - Manual - manualsarea.com

Page 2 - CAUTION; WARNING

2 © Wagner. All rights reserved. Table of Contents Safety Precautions .................................................................2 General Description ...............................................................3 Specifications ..................................................................

Page 3 - Earthing Instructions; General Description

• Do not use materials with a flashpoint below 21° C (70° F). Flashpoint is the temperature at which a fluid canproduce enough vapors to ignite. • Plastic can cause static sparks. Never hang plastic to enclose spray area. Do not use plastic drop cloths whenspraying flammable materials. • Use lowest ...

Page 4 - Preparing to Paint; Attaching the Tip to the Gun; Attaching the Paint Hose; Priming; Preparing to Prime

4 © Wagner. All rights reserved. Preparing to Paint Attaching the Tip to the Gun 1. Lock the trigger by rotating the trigger lock forward until it stops. POSSIBLE INJECTION HAZARD. Do not spray without the tip guard in place. Never trigger the gun unless the tip is in either the spray or the unclog ...

Page 5 - Pressure Relief Procedure

Mounting the Paint Hopper Use the following procedure to mount the paint hopper andattach the return tube on a hopper unit. 1. Align the bottom of the paint hopper with the threaded inlet valve on the paint pump block. 2. Turn the paint hopper clockwise to thread it onto the inlet valve. Continue to...

Page 6 - Spraying; Spraying Technique

6 © Wagner. All rights reserved. Spraying Spraying Technique The key to a good paint job is an even coating over the entiresurface. This is done by using even strokes. Keep your armmoving at a constant speed and keep the spray gun at aconstant distance from the surface. The best spraying distanceis ...

Page 7 - Cleanup; Overnight Storage

Cleanup Overnight Storage Shutdown 1. Turn the pressure control knob counterclockwise to the minimum setting. 2. Turn the PRIME/SPRAY valve to PRIME to release system pressure. 3. Trigger the gun to remove any pressure that may still be in the hose. 4. Lock the trigger by rotating the trigger lock f...

Page 9 - Maintenance; Removing and Cleaning the Inlet Valves

Maintenance Follow these procedures when encountering problemsindicated in the troubleshooting section. Removing and Cleaning the Inlet Valves 1. Perform the Pressure Relief Procedure, turn off and unplug the unit. 2. Remove the inlet valve assembly using a 27 millimeter socket or box end wrench. 3....

Page 10 - Troubleshooting

10 © Wagner. All rights reserved. R GB Troubleshooting Problem The sprayer does not start up. The sprayer starts up but does notdraw in paint when thePRIME/SPRAY valve is set toPRIME. The sprayer draws up paint butthe pressure drops when the gunis triggered. The sprayer will not shut off. The spray ...

Page 11 - Parts Listing; Main Assembly — Hopper Unit

© Wagner. All rights reserved. 11 GB R Parts Listing Main Assembly — Hopper Unit Item Part # Description Quantity 1 0288144 Hopper assembly ..................................1 2 ---------- Pump head assembly ...........................1 3 0555126 Diaphragm pump, 220–240 VAC ..........1 0311200 Diapr...

Page 12 - Diaphragm Pump

12 © Wagner. All rights reserved. R GB Diaphragm Pump (P/N 0555126 / 220–240 VAC or P/N 0311200 / 100–120 VAC) 13 17 18 4 5 678 9 10 11 12 13 14 15 16 1 2 3 19 20 21 22 23 25 24 26 AS-3112 0270 405 220V~240V 0508111 110V~120V 9952995 220V~240V 0275503 100V BS-546 CEE 7/7 NEMA 5-15P Item Part # Descr...

Wagner F230 - Manual

Table of Contents:

Summary

Other Wagner Models