Vermont Casting ST208 - Manual
Vermont Casting ST208 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – LP Configuration; Figure 7; Pilot Orifice Conversion; SDDVT; gas conversion; Remove pilot hood.; Gas Conversion; Remove pilot orifice.; Pilot Type 1; Remove pilot hood. (Your pilot may have a different
- Page 3 – RF Pilot conversion; Burner Orifice Conversion; Bottom View; Tilt ember bed slightly to correctly place on venturi; Table 1. Air Shutter Setting; bracket to the edge of the air shutter.; All Models
- Page 6 – Table 2. Injector Orifice Size Matrix
- Page 8 – CFM Corporation
Fuel Conversion Kit
Instructions
for Intrepid Direct Vent Gas
Stove
Kits:
Natural to LP: 20012921
LP to Natural: 20012910
WARNING!
The installation of this conversion kit must only
be undertaken by a qualified gas appliance
installer.
This kit is designed for conversion of the Intrepid Direct
Vent Gas Stove Models INDVR Series.
Tools required:
5/32” (4 mm) Allen wrench, 3/8” and
1/2” open end wrenches, needlenose pliers.
Kit contents:
Pilot orifice, injector orifice, conversion
label.
Conversion Precautions
Allow unit to cool completely before beginning conver-
sion. Before proceeding, turn control knob on valve to
OFF and turn gas supply to OFF. Turn OFF any electric-
ity that may be going to the appliance.
Conversion Procedure
1. Remove stove front. Lift stove front up and then
swing bottom out and away to disengage from the
stove body. (Fig. 1)
2. Undo the right and left latches at the top of the glass
frame. (Fig. 2)
3. Pull the top edge of the glass and frame assembly
away from the firebox face. Place the assembly out
of the way on a flat, padded surface such as a coun-
ter protected by a towel.
4. Remove the logset from the firebox.
ST967
Intrepid install front
7/07
INTREPID
ST967
Fig. 1
Remove the stove front. (Top vent shown)
ST208
glass swivel latch
12/99
ST208
Fig. 2
Release the latches to remove the glass frame.
Valve Conversion
1. Turn control knob to the OFF position, and shut off
the gas supply to the valve.
2. Allow the valve to cool to room temperature.
3. Remove the black protection cap by hand. (Fig. 3)
4. Insert a 5/32” or 4 mm Allen wrench into the hexago-
nal key-way of the screw (Fig. 4), rotate it counter-
clockwise until it is free and extract it.
��
��
�����
������������
����
Figure 3
��
��
�����
������������
����
Figure 4
20012973 7/07 Rev. 0
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 20012973 5. Check that the screw is clean and if necessary re- move dirt. 6. Flip the screw. (Fig. 5)7. Using the Allen wrench as shown in Figure 6, rotate the screw clockwise and tighten until snug. �� �� ������������������� Figure 5 �� �� ��������������������� Figure 6 WARNING: Do not overtighte...
3 20012973 • Remove pilot orifice with needlenose pliers. (Fig. 12) NOTE: Use a wrench to hold pilot tube in place while removing the orifice. • Install the conversion orifice. • Reinstall pilot hood and tighten until mark on pilot hood aligns with mark on pilot bracket. CO144 RF Pilot conversion 6/07 ...
6 20012973 Table 2. Injector Orifice Size Matrix Conversion to LP Input (BTU/h) Kit # Orifice Part # Minimum Maximum 20012921 #56 (.0465”) 30000336 12,000 16,000 Conversion to Natural Gas Input (BTU/h) Kit # Orifice Part # Minimum Maximum 20012910 #47 (.0785”) 20003054 12,500 18,500
