Vermont Casting SDDVT - Manual

Table of Contents:

• Page 2 – Stardance Direct Vent/Natural Vent Gas Heater; Table of Contents
• Page 3 – General Information; Proposition 65 Warning:; Fuels used in gas, woodburning or
• Page 4 – Installation Requirements; “GAS VENT DIRECTLY BELOW, KEEP; MANUFACTURER REQUIREMENTS; Gas Equipment Venting System NOT Provided
• Page 5 – Stardance Direct Vent / Natural Vent Dimensions; SDDVT Models; SDDVTC Models; Attention; Stardance dimensions.
• Page 6 – Clearance Requirements; Possible stove locations.; • Always maintain required clearances; Locating the Stove; We do not recommend the use of wallpaper
• Page 7 – Direct Vent Only; Stardance
• Page 8 – Gas Inlet and Manifold Pressures; Stardance Direct Vent / Natural Vent; High Elevations; Gas Specifications; Input; Air Shutter Setting
• Page 9 – Vertical Termination - Direct Vent ONLY; NOTE: The restrictor plate supplied; Restrictor Plate Adjustment; Examples for Extended Run/Restrictor Plate Settings
• Page 10 – Vent Termination Clearances; Location of Vent Termination
• Page 11 – General Venting Information - Termination Location; Canadian Installations
• Page 12 – Termination clearances.; Venting Requirements - Natural Vent Only; = Acceptable venting configuration; Vent termination window - Natural Vent ONLY.; Outside Corner; Termination Clearances; with no side wall; of Caps
• Page 13 – Venting Requirements and Options -; Approved Vent System Components; Minimum Horizontal Vent Kit; Selkirk Corporation Vent Components; Direct vent pipe may be used on the Natural
• Page 14 – CFM Vent Components
• Page 15 – Install the Optional Fan; WARNING; The rheostat control switch attaches to the left side; Fan kit components.; Remove the rear skirt insert panel at the bottom of; install fan kit; Remove rear skirt insert.; attach fan; Attach the fan assembly and the snapstat.; JUV; Attach the fan rheostat.
• Page 16 – Venting System Assemlby - Direct Vent; For Canadian installations:; Connect the inner starter with the next section of in-; Attach inner assembly to flue collar.; Install the Vent Adapter Pipe; install outer adpater
• Page 17 – dura vent; Side Wall Termination Assembly; Vent Opening; CFM System; Locate vent opening.; Install Vent Adapter Pipe; For DuraVent pipe only:
• Page 18 – Zero Clearance Sleeve; Assemble the wall sleeve and firestop.; Determine the vertical pipe length.; measure thru wall; Measure the horizontal length.; install pipe thru wall; Install the horizontal pipe and wall plate parts.; install wall terminal; Install the vent terminal.
• Page 19 – install snorkel; Snorkel kit installation.; snorkel detail; Use extension brackets to mount snorkel against; Vent Termination Below Grade; If the; Vent Assembly
• Page 20 – vent thru ceiling; Install firestops and attic insulation shield.; vent thru roof; Roof support and flashing.; Selkirk Direct-Temp Metalbestos Direct; Installation Instructions; Model DT Ceiling Support (CS) Cathedral Ceiling Wall Thimble; Use of Sealant
• Page 21 – Vertical Venting; Inlet End; Fig. 34 Selkirk Venting Components
• Page 22 – Supporting DIRECT-TEMP: Horizontal Support; Horizontal Installation
• Page 23 – As a general rule, the wall thimble is optional in; When installed in Canada, a; Below grade installation.; The wall thimble accommodates wall thickness-
• Page 24 – Horizontal Termination; If a vertical rise is necessary on the exterior side; do not back fill; Vertical Installation; Typical vertical venting configuration.; Frame openings to the dimensions specified
• Page 25 – If the cathedral ceiling support box assembly is; Minimum; Fig. 44 Minimum Height Above Roof Requirements; Venting System Assembly - Natural Vent
• Page 26 – Install the Vent Pipe; Decorative; Decorative 7” pipe may be fitted around the B-vent; Install the Log Set; Do not use
• Page 27 – Install the left log by
• Page 28 – Connect the Gas Supply Line; CAUTION; Gas connection should be made in ac-; Burner Information; In order to connect Natural Gas,; In order to connect Propane,; use a fitting with 3/8”; Install ON/OFF Switch; Run wires down back of stove, under bottom of rear; attach switch assy; Attach switch assembly to rear shroud.; Attach switch wires to valve.
• Page 29 – Use only a thermostat rated for 500 millivolts.; Install the wall thermostat in the desired location and; Install the Front Plate; Install the front plate.; This completes assembly of the Stardance stove.; Operation; Your First Fire; SDDVT; Pilot assembly location.
• Page 30 – Flame & Temperature Adjustment; Flame adjustment knob for SIT valve.; Flame Characteristics; Pilot flame; Correct pilot and burner flame patterns.; SDDVT Series
• Page 31 – FOR YOUR SAFETY READ BEFORE LIGHTING; Follow the gas supplier’s instructions.; To Turn Off Gas To Heater; Lighting and Operating Instructions; Lighting Instructions; Euro SIT; Lighting instructions
• Page 32 – Troubleshooting the Gas Control System (SDDVT Series); NOTE; SIT NOVA 820 MILLIVOLT VALVE
• Page 33 – Comfort control valve.; Transmitter diagram.
• Page 34 – LED Count; Pilot; Comfort Control Valve; Comfort valve wiring diagram.
• Page 35 – Local Path
• Page 36 – Auto Path; If the setting is; above; If the settings is; below
• Page 37 – Fuel Conversion Instructions; attach gas line; Attach the gas line to the left side of the valve.; Conversion Precautions; LP Configuration; SDDVTC Series Models
• Page 38 – Valve; Depress and turn center plunger.; Pilot Orifice Conversion; Pilot Type 1; gas conversion; Pilot type 2; Rf pilot Conversion; Remove pilot hood. (Your pilot may have a different; RF Pilot conversion; Remove pilot orifice.
• Page 39 – Bottom View; Tilt ember bed slightly to correctly place on venturi; Burner Orifice Conversion; Use two wrenches to avoid damage to manifold.
• Page 40 – Conversion to Natural Gas; Table 2. Injector Orifice Size Matrix; Conversion to LP
• Page 41 – Maintenance; Annual System Inspection; ERATE THE HEATER WITH DAMAGED LOGS.; Care of Cast Iron; Remove the stove front.; Glass Replacement
• Page 42 – Release the latches to release the glass frame.; Gasket Replacement; Determine the correct length of gasket by laying it; glass gasket detail; Wrap the gasket material around the outside iedge of; Inspect the Vent System Annually
• Page 43 – Wiring Diagrams; Thermostat; On/Off switch and optional thermostat circuit.; AN; BLK; FK26 wiring diagram; Schematic Diagram; Stardance fan circuit.; Wiring for RF Valve
• Page 46 – Fuel Conversion Kits
• Page 47 – Optional Accessories; Fan Kits
• Page 51 – PLATED PARTS AND ACCESSORIES:; LIMITED LIFETIME WARRANTY
• Page 52 – CFM Corporation