Vermont Casting SDDVRBS - Manual

Table of Contents:

• Page 2 – Stardance Direct Vent - Rear Vent Gas Heaters; may result in a possible fire hazard and will void the warranty.; Table of Contents
• Page 3 – Completion of sale, nor for purpose of resale,; Installation & Operating Instructions; Proposition 65 Warning:; Fuels used in gas, woodburning or; Stardance Direct Vent / Rear Vent
• Page 4 – “GAS VENT DIRECTLY BELOW, KEEP; MANUFACTURER REQUIREMENTS; Gas Equipment Venting System NOT Provided
• Page 5 – SDDVR; SDDVR Models; Stove Dimensions - Stardance Direct Vent Gas Heater; Stardance dimensions.
• Page 6 – Installation Requirements; Locating the Stove; We do not recommend the use of wallpaper; Possible stove locations.; Clearance Requirements; Minimum Clearances to Combustible Materials
• Page 7 – Parallel installation, minimum back and side clearance.; stardance; Corner installation, minimum corner clearance and flue; SDVR; Width; Pinnacle
• Page 8 – Gas Specifications; Input Input; Gas Inlet and Manifold Pressures; Air Shutter Setting; High Elevations
• Page 9 – Vertical Termination; NOTE: The restrictor plate supplied with; A vertically terminated vent system must; Some installations may require some adjust-; Restrictor Plate Adjustment; Install restrictor plate as shown in Figure 9 with; Examples for Extended Run/Restrictor Plate Settings; completely down; Vertical vent termination window.
• Page 10 – Important: All vent clearances must be maintained.; Obstructions or impediments to venting.; IMPORTANT; Vent Termination Clearances; Location of Vent Termination
• Page 11 – Canadian Installations; General Venting Information - Termination Location
• Page 12 – Termination clearances.; Termination Clearances; of Caps
• Page 13 – Vent Components
• Page 14 – The upper flange of the fan skirt should be located; Installation; Correct position of fan skirt installation.; Stardance RV; Snapstat assembly and installation.; Unpack the Stove
• Page 15 – rear vent kit; Rear Vent Kit 7TFSRSK installation.; Vent Opening; Locate vent opening.; Vent Opening - Combustible Wall; Venting System Assembly; For Canadian installations:; Rear Vent; Apply sealant to the starter pipe, and fasten to stove; JUV; Attach rheostat to bracket.
• Page 16 – wall thimble; Minimum wall thimble centerline.; Vent Termination Below Grade; Install inner starter pipe and inner elbow.; Side Wall Termination Assembly
• Page 17 – Assemble the wall sleeve and firestop.; Determine the vertical pipe length.; install pipe thru wall; Install the horizontal pipe and wall plate parts.; measure thru wall; Measure the horizontal length.
• Page 18 – Install the vent terminal.; If the; Pinstar; Snorkel kit installation.; snorkel detail; Use extension brackets to mount snorkel against
• Page 19 – Vent Assembly; vent thru ceiling; Install firestops and attic insulation shield.; vent thru roof; Roof support and flashing.; Vertical Through Existing Chimney
• Page 20 – blue line; Fireplace; Fireplace Vent System; Fireplace vent system installation.
• Page 21 – Minimum lintel height for flush or forward placement.; Fireplace Installation Requirements; less completely covered by field fabricated sheet metal. If; Fireplace Installations Using Existing Wood Stove Chimneys
• Page 22 – Selkirk Direct-Temp Metalbestos Direct; Installation Instructions; Determine whether the length of pipe fits the appli-; Framing Dimension Table 1; Use of Sealant; Inlet End
• Page 24 – Supporting DIRECT-TEMP: Horizontal Support; Horizontal Installation; Below grade installation.; As a general rule, the wall thimble is optional in; When installed in Canada, a; The wall thimble accommodates wall thickness-
• Page 25 – Horizontal Termination; Vinyl siding standoff and horizontal termination.; If a vertical rise is necessary on the exterior side; do not back fill; Vertical Installation; Frame openings to the dimensions specified
• Page 26 – Typical vertical venting configuration.; If the cathedral ceiling support box assembly is; Minimum; Fig. 47 Minimum Height Above Roof Requirements; Whenever DIRECT-TEMP penetrates through a
• Page 27 – Connect the Gas Supply Line; attach switch assy; Attach switch assembly to rear shroud.
• Page 28 – Thermostat; Thermostat Connection; Use only a thermostat rated for 500 - 750 millivolts.; Install the wall thermostat in the desired location and; Install the Front Plate; attach switch; Attach switch wires to valve.; Stardance; Install Stove Front.
• Page 29 – Do not use; Install the Log Set
• Page 31 – Operation; Pilot and Burner Inspection; RADVT valve control.; SDDVT; Pilot assembly location.; Flame & Temperature Adjustment; Flame adjustment knob for SIT valve.; Your First Fire
• Page 32 – Flame Characteristics; Pilot flame; Correct pilot and burner flame patterns.; SDDVT Series
• Page 33 – FOR YOUR SAFETY READ BEFORE LIGHTING; WHAT TO DO IF YOU SMELL GAS; To Turn Off Gas To Heater; Lighting And Operating Instructions; Lighting Instructions; Euro SIT; Lighting instructions
• Page 34 – Troubleshooting the Gas Control System (SDDVT Series); NOTE; SIT NOVA 820 MILLIVOLT VALVE
• Page 35 – comfort valve; Honeywell; Comfort control valve.
• Page 36 – If an Error Code 3 is observed while performing the; Valve
• Page 37 – Local Path
• Page 38 – Auto Path; If the setting is; above; If the settings is; below
• Page 39 – attach gas line; Attach the gas line to the right side of the valve.; Conversion Precautions; LP Configuration; SDDVRC Series Models
• Page 40 – Gas Conversion; gas conversion; Depress and turn center plunger.; Pilot Orifice Conversion; Pilot Type 1; Rf pilot Conversion; Remove pilot hood. (Your pilot may have a different; RF Pilot conversion; Remove pilot orifice.; Pilot type 2
• Page 41 – Burner Orifice Conversion; Bottom View; Tilt ember bed slightly to correctly place on venturi; bracket to the edge of the air shutter.; All Models
• Page 42 – Table 2. Injector Orifice Size Matrix; Conversion to Natural Gas
• Page 43 – Maintenance; DO NOT; painted surfaces; Remove the Stove Front.
• Page 44 – Gasket Replacement; Determine the correct length of gasket by laying it; Inspect the Vent System Annually; glass gasket detail; Wrap the gasket material around the outside edge of; Stove Disassembly
• Page 45 – rdv connections diag.; Schematic Diagram; Wiring Diagrams; On/off switch and optional thermostat circuit.; wiring
• Page 46 – Stardance Direct Vent/Rear Vent Gas Heater:; Models
• Page 47 – Stardance Direct Vent/Rear Vent Gas Heater
• Page 48 – Fuel Conversion Kits; Conversion Kit, NG to LP - SDDVRC Series; Color
• Page 49 – Optional Accessories; Fan Kits; Specifications; Refer to Page 13 for installation instructions.; Remote Controls; Model Functions Controlled; ON/OFF and Temperature; Screen Kit; Model Color; Midnight Blue
• Page 51 – PLATED PARTS AND ACCESSORIES:; LIMITED LIFETIME WARRANTY
• Page 52 – Efficiency Ratings; Model; CFM Corporation