Vermont Casting DV580 - Manual

Table of Contents:

• Page 2 – DV360/580 Series Direct Vent Gas Fireplace; Installation & Operating Instructions; Proposition 65 Warning:; PLEASE READ THE FOLLOWING CAREFULLY; Locating Your Fireplace
• Page 3 – Fireplace Dimensions (Installed as Top Vent); Fireplace specifications and framing dimensions.; Framing Dimensions
• Page 4 – Fireplace Dimensions (Installed as Rear Vent)
• Page 5 – Clearance to Combustibles; Combustible mantel minimum installation.; Hearth; Mantel; Combustible mantel leg minimum installation.
• Page 6 – Framing And Finishing; Flange Location for; Final Finishing; side nailing flange; Adjustable Drywall Strip; Certified To; Gas Specifications; GAS; Gas Inlet and Manifold Pressures
• Page 7 – High Elevations; INSTA VENT FREE; Typical gas supply installation.; Remote ON/OFF Switch Installation; Attach the wire to the ON/OFF switch and install; Remote switch; Remote switch wiring diagram for R models.; Alternate Switch Location; alternate; Alternate switch location.
• Page 8 – Electronic Gas Control Valve; Honeywell ignition module.
• Page 9 – Optional Top Vent Application; Secure flue cover to back of flue outlet. Be sure to; Remove screws from outer collar adapter.; Outer Collar Adapter; Remove flue cover and flue pipe.; CAUTION: Remove insulation. Insulation extends; Replace flue cover and flue pipe.; Outer Collar Adapter; Complete conversion.
• Page 10 – General Venting; • Venting terminals shall not be recessed into a wall or; Location of Vent Termination
• Page 11 – General Venting Information - Termination Location; Canadian Installations
• Page 12 – Termination Clearances; Termination clearances.; General Information Assembling Vent Pipes; Flex Vent Pipes; flex vent; Apply high temperature sealant to 4” and 7” pipes.
• Page 13 – Twist Lock Pipes; How to Use the Vent Graph; ertical dimension form the fl; Rear Wall Vent Application
• Page 14 – Rear Vent Top View, Corner Installation; Rear Wall Vent Installation; When using flex vent, the opening will have to; Noncombustible Walls:; Hole opening should be 7; Vent Opening; Vent Opening for Combustible Walls; Locate vent opening on wall.; Adjustable zero clearance sleeve.; Rear vent no elbows; Rear Vent Top View
• Page 15 – Side View Vent Termination; Side view of final unit location.; Rear Wall Vent Installations -; Follow Steps 1 and 2 on Page 15.; Grasp the vent pipe close to the collar and bend to; There must be a 1/2” rise per foot length.; Vertical Sidewall Application; • The maximum number of 90° elbows per side wall
• Page 16 – Vertical Sidewall Installation; Hole opening must be 7
• Page 17 – • If a 90° elbow is used in the horizontal vent run; Maximum horizontal run with no rise.; Maximum vent run with elbows.; • For each 45° elbow installed in the horizontal run,; Maximum elbow usage.
• Page 18 – Horizontal length requirement.; spacer springs; Install spacer springs.; Install the 4” flex then 7” flex to the termination.; Bend flex vent at 90° so horizontal portion is 6
• Page 19 – Below Grade Installation; Top Vent; Below grade installation.; Snorkel; Snorkel installation, recessed foundation.
• Page 20 – Support straps for horizontal runs.; attic insulation shield; Upper Floor
• Page 21 – Minimum termination to roof clearance.
• Page 22 – Vent Components; Vent components; Elbow
• Page 23 – Operating Instructions; ment glass will void all product warranties.; remove louvre; Tilt window frame assembly out slightly at the bot-; Window frame assembly removal.; firebox toward the front.
• Page 24 – hearth Panels; Front of Unit; Hearth panel location.; Installation of Logs; Logs; Burner brackets and bends.
• Page 25 – Place the glowing embers by
• Page 26 – Place the lava rock on the; DV580 log, burner lava rock and ember placement.; Place large lava rock around the front grate.
• Page 27 – Burner Lava Rock Placement; Flame adjustment knob for Honeywell valve.; Flame adjustment knob for SIT valve.; Flame Characteristics; PSE Pilot; Correct pilot flame appearance.; Inspecting the Venting System
• Page 28 – Correct burner flame apperance for DV360 and DV580.
• Page 29 – Instructions for RF Comfort Control Valve; Comfort control valve.; Shut Off Procedure; comfort valve
• Page 30 – Valve; Comfort Valve wiring diamgram.
• Page 31 – LED Count; Auto Path
• Page 32 – Local Path
• Page 33 – Burner orifice replacement.; Remove manifold assembly.
• Page 34 – Front View; Remove air shutter from burner pan.; Pilot Orifice Conversion; Remove pilot orifice.; Fuel Conversion Instructions; Conversion Procedure; Depress and turn center plunger.
• Page 35 – Table 1 Injector Orifice Size Matrix; NEVER test with an open flame.
• Page 39 – Fuel Conversion Kits
• Page 40 – Optional Accessories; Fan Kits; Fan placement; Side View; FK12 Fan Kit placement.; FK24 Fan Assembly; Method A; FK24 fan placement.; WIRING DIAGRAM
• Page 41 – Remote Controls; Model; Ceramic Refractory Panels; Unit; Installation Instructions; rear ceramic support; Rear ceramic panel placement.; Decorative Bay Windows; Installation; Decorative Frame Trims; Section A
• Page 42 – For Use in Mobile Homes: Model DV360RMH; Conversion Instructions; a. Units with SIT valve
• Page 43 – a) Using a Torx T20 or slotted screwdriver, remove
• Page 44 – BASIC WARRANTY; IF WARRANTY SERVICE IS NEEDED...; ) Contact your supplier. Make sure you have your; LIMITED LIFETIME WARRANTY; PRODUCT COVERED BY THIS WARRANTY
• Page 45 – Efficiency Ratings; CFM Corporation