Page 2 - TABLE OF CONTENTS
- 2 - TABLE OF CONTENTS PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE. IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to follow these instructions may result in a possible fire hazard and will void the warranty. Instal...
Page 3 - CLEARANCE TO COMBUSTIBLES; INSTALLATION AND OPERATING INSTRUCTIONS; LOCATING YOUR GAS FIREPLACE
- 3 - 12" (305mm) 12" (305mm) A B C E D This gas fireplace should be installed by a qualified installer inaccordance with local building codes and with current CAN /CGA-B149 (. 1 or .2) Installation codes for Gas Burning Fireplacesand Equipment and CAN/CSA Z 240 .4 Canada. FOR U.S.A Installa...
Page 4 - D E; FIREPLACE DIMENSIONS
- 4 - A B C D E F G H J I K FIREPLACE DIMENSIONS MODEL D232 A 25" 635mm B 24 1/8" 613mm C 16" 406mm D 20" 508mm E 19" 483mm F 21" 533mm G 31 3/4" 806mm H 17 3/4" 451mm I 29 5/8" 752mm J 9" 229mm K 6 1/2" 165mm L — — M — — N — — MODEL D232
Page 5 - GAS INLET & MANIFOLD PRESSURES; Input Minimum; ways check for gas leaks with a mild soap; GAS LINE INSTALLATION; It is most; Vented Gas Fireplace Heaters; PREPARATION; GAS SPECIFICATIONS; TYPICAL GAS LINE CONNECTION
- 5 - GAS INLET & MANIFOLD PRESSURES Input Minimum Input Maximum Manifold Pressure NATURAL LP (Propane) 11" wc 13" wc 10" wc 4.5" wc 7" wc 3.5" wc Al ways check for gas leaks with a mild soap and water solution. Do not use an openflame for leak testing.The gas control is ...
Page 6 - MILLIVOLT THERMOSTAT; THERMOPILE; PILOT; TP; INSTALLATION OF REMOTE
- 6 - PILO T TPTH TP TH ON/OFF SWITCH OR MILLIVOLT THERMOSTAT VALVE THERMOPILE Fig. 4 DO NOT USE THIS FIREPLACE IF ANYPART OF THIS FIREPLACE HAS BEENUNDER WATER. IMMEDIATELY CALLA QUALIFIED SERVICE TECHNICIANTO INSPECT THE HEATER AND TOREPLACE ANY PART CONTROLWHICH HAS BEEN UNDER WATER. When using c...
Page 7 - clearance to outside comer see next page; Location of Vent Termination; GENERAL VENTING INFORMATION
- 7 - ; ; ;; ;; ;; V V V V V V V V V X X ;; ;; X D E B B B C B M B A J K A F L G G ; TERMINATION CAP AIR SUPPLY INLET GAS METER RESTRICTED AREA(TERMINATION PROHIBITED) H I Fixed Closed Fixed Closed Openable Openable Fixed Closed G G N N A A = clearance above grade, veranda, porch, deck, or bal-cony ...
Page 8 - Termination Clearances; Recessed Location
- 8 - ;;;; ;; ; Outside Corner Inside Corner Termination Clearances Termination clearances for buildings with combustible and noncombustible exteriors. A =Combustible 6"(152mm) Noncombustible 2"(50mm) B =Combustible 6"(152mm) Noncombustible 2"(50mm) ; ;; A ;; ;; ;; Balcony - with no ...
Page 9 - CRIMPED END PIPES; CANADIAN INSTALLATIONS:; TWIST LOCK PIPES; TWIST LOCK PIPE JOINT; Screw Holes
- 9 - GENERAL INFORMATION ON ASSEMBLING THE VENT PIPES Join pipes and secure joints with three (3) sheetmetalscrews. (See Fig. 6) Wipe off excess sealant. There are polished brass decorative ringsprovided to hide the exposed pipingjoints. Wrap the brass ring over the jointfitting the stud into the n...
Page 10 - VERTICAL SIDEWALL INSTALLATIONS; The maximum number of elbow degrees in a system is 270; Total; VERTICAL SIDEWALL APPLICATIONS; Fig. 10. This does not apply if the 90 degree
- 10 - VERTICAL SIDEWALL INSTALLATIONS Since it is very important that the venting systemmaintain its balance between the combustion air intakeand the flue gas exhaust, certain limitations as to ventconfigurations apply and must be strictly adhered to. The graph showing the relationship between vert...
Page 11 - HORIZONTAL DIMENSION; ONLY; SIDEWALL VENTING GRAPH; HORIZONTAL DIMENSION
- 11 - 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 eg: A eg: B VERTICAL DIMENSION FROM THE FLOOR OF THE FIREPLACE TO THE CENTRE OF THE HORIZONTAL VENT PIPE SIDEWALL VENTING GRAPH (Dimensions in Feet) HORIZONTAL DIMENSION...
Page 12 - VENT PIPE ASSEMBLY; STEP 4; BEAD OF SEALANT
- 12 - STEP 2 Measure wall thickness and cut zero clearance sleeveparts to proper length (MAXIMUM 12"). Assemble sleeveand attach to firestop with #8 sheetmetal screws (sup-plied). Install firestop assembly (Fig. 16).. Zero clearance sleeve is only required forcombustible walls. #8SCREWS(2) ADJU...
Page 13 - BELOW GRADE INSTALLATIONS
- 13 - ; ; ; ; ; STEP 6 Note: If using the charcoal wall plate, Part #52202-CG,and collar, Part #52203-CG, put them in place beforeputting the pipe sections through the wall. Use appropriate length of pipe sections - telescopic or fixed- and install. The sections which go through the wall arepackage...
Page 14 - Example: Maximum horizontal length
- 14 - GRAVEL DRAIN FIRESTOP FOUNDATION WALL WINDOW WELL SNORKEL GROUND 24"/608mm MINIMUM* A minimum of 24"/608mmvertical pipe must be installedwhen using the snorkel kit. The 22" vertical rise (center to center) of the snorkel may beincluded for calculation of max.horizontal run. * 7...
Page 15 - VERTICAL THRU THE ROOF APPLICATIONS; Locate your fireplace.; TO INSTALL VERTICAL VENTING; d) Two sets of 45 degree elbow offsets within these
- 15 - VERTICAL THRU THE ROOF APPLICATIONS 1. Locate your fireplace. 2. Plumb to centre of the (4") flue collar from ceilingabove and mark position. 3. Cut opening equal to 9-3/8" x 9-3/8" (240 mm x 240 mm). 4. Proceed to plumb for additional openings through theroof. In all cases, the o...
Page 16 - CRIMPED ENDS VENTING COMPONENTS
- 16 - CRIMPED ENDS VENTING COMPONENTS Starter Kit -Model 7DVSK - Sidewall Venting Starter Kit - Model 7TDVSKV - Vertical Venting for 7DVSKV-A order 1/12 to 6/12 roof pitchfor 7DVSKV-B order 7/12 to 12/12 roof pitchfor 7DVSKV-F order flat roof Starter Kit - Model 7TDVSKS -Snorkel Kit for Below Grade...
Page 17 - TWIST LOCK VENTING COMPONENTS
- 17 - TWIST LOCK VENTING COMPONENTS Starter Kit -Model 7TDVSK - Sidewall Venting Starter Kit - Model 7TDVSKV - Vertical Venting for 7TDVSKV-A order 1/12 to 6/12 roof pitchfor 7TDVSKV-B order 7/12 to 12/12 roof pitchfor 7TDVSKV-F order flat roof Starter Kit - Model 7TDVSKS -Snorkel Kit for Below Gra...
Page 18 - GENERAL GLASS INFORMATION; The use of substitute glass will void all product; OPERATING INSTRUCTIONS; LOUVRE REMOVAL; GLASS REMOVAL; Remove frame window by pulling it forward and up.
- 18 - GENERAL GLASS INFORMATION Only glass approved for use in with this productmay be used for replacement. 1. The use of substitute glass will void all product warranties. 2. Care must be taken to avoid breakage of the glass. Under no circumstances should this fireplacebe operated without the fro...
Page 19 - Remove logs from packaging.
- 19 - Fig. 34 GLASS CLEANING It will be necessary to clean the glass periodically.During start-up condensation, which is normal, forms onthe inside of the glass and causes lint, dust and otherairborne particles cling to the glass surface. Also initialpaint curing may deposit a slight film on the gl...
Page 20 - CLEANING PROCEDURE; Turn off pilot light at gas valve.; CAUTION: LOGS MAY BE HOT; Check pilot and main burner operation.; MAINTENANCE; LO; FLAME CHARACTERISTICS; PSE PILOT
- 20 - Fig. 38 FLAME ADJUSTMENT (RN/RP MODELS) For units equipped with Hi/Lo valves, flame adjustmentis accomplished by rotating the Hi/Lo adjustment knoblocated near the centre of the gas control. (Fig. 38 & 39) L O HI Turn counterclockwise to increase flame height. Turn clockwise to lower flam...
Page 21 - TO TURN OFF GAS TO APPLIANCE; FOR YOUR SAFETY READ BEFORE LIGHTING; TO TURN OFF GAS TO FIREPLACE; LIGHTING AND OPERATING INSTRUCTIONS; LIGHTING INSTRUCTIONS; EURO SIT
- 21 - TO TURN OFF GAS TO APPLIANCE 4. Push in gas control knob slightlyand turn clockwise to "OFF". Do not force. 5. Close control access panel. 10. Push the control knob all the way in and hold. Immediately light the pilot by repeatedly depressingthe piezo spark ignitor until a flame appea...
Page 22 - START; CHECK; TROUBLE SHOOTING THE GAS CONTROL SYSTEM; HONEYWELL MILLIVOLT VALVE
- 22 - • GAS SUPPLY ON • SUPPLY LINE HOOKED UP• SHUTOFF VALVE OPEN NO NO NO NO • LOCKOUT HAS ENGAGED. WAIT 60 SECONDS AND TRY AGAIN.• FOR SPARK AT ELECTRODE WHILE DEPRESSING PIEZO — 1/8" GAP TO PILOT HOOD NEEDED.• ALL WIRING CONNECTIONS• REPLACE PIEZO IGNITOR • FOR AIR IN THE LINES• THERMOPILE N...
Page 23 - TROUBLE SHOOTING THE GAS CONTROL SYSTEM; SIT NOVA 820 MILLIVOLT VALVE
- 23 - TROUBLE SHOOTING THE GAS CONTROL SYSTEM SIT NOVA 820 MILLIVOLT VALVE Note: Before trouble shooting the gas control system, be sure external gas shut off is in the "On" position. WARNING: BEFORE DOING ANY GAS CONTROL SERVICE WORK, REMOVE GLASS FRONT. SYMPTOM POSSIBLE CAUSES CORRECTIVE ...
Page 24 - REPLACEMENT PARTS LIST; ESCRIPTION; D232
- 24 - REPLACEMENT PARTS LIST D ESCRIPTION D232 1. Log Set Complete 10000160 1a. Log Ember Front KR1 1b. Log Front Left KR2 1c. Log Front Right KR3 1d. Log Rear KR4 1e. Log Top Left KR5 1f. Log Top Right KR5 2. Burner Lava Rock (Package) 57897 3a. Burner with Tiles Nat. 57903 3b. Burner with Tiles P...
Page 25 - FREESTANDING REPLACEMENT PARTS
- 25 - FREESTANDING REPLACEMENT PARTS 10a/b 29 30 27 5/6 a,b 28 21a,b 44 41 42 43 31 32 36 a/b 37 39 46 45 it H I LO OFF PIL OT 25a,b 39 40 33 47 26 10 33 43 43 39 #1 - COMPLETE LOG SET 1b 1d 1e 1f 1a 1c 3a/b 4 23 22 43 41 42 2 19 7 a/b 18 13 11 12 17 16 LO HI PILOT ADJ PILOT ON OFF 24a,b 15 17 13 8...
Page 26 - OPTIONS; REMOTE CONTROL; MRC2 - Temperature Control Remote; of any replacement components see Fig. 43.
- 26 - FAN KIT - FK24 It will be easier to install the fan beforeconnecting the gas line to the fireplace. 1. Open front access door panel by pulling forward onbrass lip. 2. Install the fan through the opening at the back of thepedestal, with the outlet pointed up and the fan mountingbracket facing ...
Page 28 - LIMITED WARRANTY & EXTENDED LIFE TIME PROTECTION; For Gas Appliance Products*
- 28 - 410 Admiral Blvd. • Mississauga, Ontario, Canada L5T 2N6 • 905-670-7885 www.vermontcastings.com CFM Majestic, Inc. © Copyright CFM Majestic, Inc. 10002735 6/00 BASIC WARRANTY:The CFM Majestic, Inc.™ (hereinafter referred to collectively as the"Company") warrants that your new Vermont ...