Vermont Casting 4070 - Manual

Table of Contents:

• Page 2 – Pinnacle & Stardance Direct Vent - Rear Vent Gas Heaters; Table of Contents; Installation & Operating Instructions
• Page 3 – from the manufacturer.
• Page 4 – Stove Dimensions - Pinnacle Direct Vent Gas Heater
• Page 5 – Clearance Requirements; Minimum Clearances to Combustible Materials; Minimum Clearances; Parallel Installation; SDVR; • Always maintain required
• Page 6 – Alcove Installation; Hearth Requirements; Input; Natural; Gas Inlet and Manifold Pressures; PDV20 and SDVR
• Page 7 – High Elevations; elbows may be substituted for each single; Ve; Fig. 7 Horizontal vent termination window.
• Page 8 – Vent Termination Clearances; IMPORTANT; Fig. 8 Vertical vent termination window.; ” Restrictor
• Page 9 – Location of Vent Termination
• Page 10 – Canadian Installations; General Venting Information - Termination Location
• Page 11 – Outside Corner; Termination Clearances; Recessed Location
• Page 12 – Vent Components
• Page 13 – Installation; Fig. 13 Correct position of fan skirt installation.; Fig. 11 Snapstat assembly and installation.; Unpack the Stove
• Page 14 – Locate the vent opening on the wall. Refer to; Fig. 18 SDVR with Rear Vent Kit 7TFSRSK installation.; Venting System Assembly -; Run a bead of sealant beneath the pipe bead and; Blower Wiring Diagram
• Page 15 – Vent Termination Below Grade; Fig. 19 PDV20 with Rear Vent Kit 7TFSRSK installation.
• Page 16 – Side Wall Termination Assembly; Locate the vent opening on the wall. Refer to; Vent Opening - Combustible Wall; Fig. 25 Assemble the wall sleeve and firestop.; Fig. 22 Install inner starter pipe and inner elbow.
• Page 17 – Fig. 26 Determine the vertical pipe length.; Fig. 28 Install the horizontal pipe and wall plate parts.
• Page 18 – Vent Assembly; ” restrictor plate, to; Level the soil to maintain a 4” clearance below the
• Page 19 – Fig. 33 Install firestops and attic insulation shield.; Install appropriate pipe sections until the vent run; Vertical Through Existing Chimney; Obstructions or impediments to venting.; Clean the top of the chimney as needed, to ensure a; good seal between it and the vent termination.; Slide the insulation sleeves provided in the termina-
• Page 20 – Apply high-temperature sealant to the top of the; Trim the flex liners as needed. Each should be only; Fireplace Vent System
• Page 21 – Fig. 36 PDV20 minimum lintel height for flush or forward placement.; Fireplace Installation Requirements - PDV20; Fireplace Installations Using Existing Wood Stove Chimneys
• Page 22 – Fig. 38 SDVR minimum lintel height for flush or forward placement.; Fireplace Installation Requirements - SDVR; Fig. 39 SDVR installations using existing wood stove chimney pipe.
• Page 23 – Connect the Gas Supply Line; Run wires down back of stove, under bottom of rear
• Page 24 – Thermostat; Thermostat Connection; Use only a thermostat rated for 500 - 750 millivolts.; Install the wall thermostat in the desired location; Install the Front Plate; Fig. 40 Attach switch assembly to rear shroud.
• Page 25 – Install the Log Set; Install the rear log by centering it side to side on the
• Page 26 – Operation; Your First Fire; Flame & Temperature Adjustment; LO; Fig. 49 Flame adjustment knob for Honeywell valve.; Flame Characteristics
• Page 28 – FOR YOUR SAFETY READ BEFORE LIGHTING; To Turn Off Gas To Heater; Lighting And Operating Instructions; Lighting Instructions; Euro SIT
• Page 29 – Troubleshooting / Honeywell #8420 Gas Control System; SYMPTOM
• Page 31 – If an Error Code 3 is observed while performing the; Valve
• Page 32 – Local Path
• Page 33 – Fuel Conversion Instructions; Fig. 56 Attach the gas line to the right side of the valve.; Auto Path; Remove stove front. Lift stove front up and then
• Page 34 – Pilot Type 1; Pilot type 2
• Page 35 – NOTE: Be sure burner leg remains at a 90; Fig. 63 Depress and turn center plunger.; Fig. 64 Remove and replace injector orifices.; Conversion to LP; Table 2. Injector Orifice Size Matrix; Conversion to Natural Gas
• Page 36 – Maintenance
• Page 37 – Gasket Replacement; Determine the correct length of gasket by laying it; Inspect the Vent System Annually; Fig. 66 Release the latches to release the glass frame.
• Page 38 – B L; Schematic Diagram; Stove Disassembly; C WIRE OR ITS EQUIVALENT.; Wiring Diagrams
• Page 39 – CEMENT
• Page 42 – Optional Accessories; Fan Kits
• Page 43 – BASIC WARRANTY; IF WARRANTY SERVICE IS NEEDED...; ) DO NOT ATTEMPT TO DO ANY SERVICE WORK; LIMITED LIFETIME WARRANTY
• Page 44 – CFM Specialty Home Products