Vermont Casting 36XDV - Manual

Vermont Casting 36XDV

Vermont Casting 36XDV – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
Page: / 56

Table of Contents:

  • Page 2 – XDV Direct Vent Gas Fireplace; PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS; Table of Contents
  • Page 3 – OFF; PLEASE REVIEW THE FOLLOWING CAREFULLY; Locating Your Fireplace; Installation & Operating Instructions
  • Page 4 – Framing Dimensions; XDV Fireplace Dimensions - Installed as Rear Vent; Fireplace specifications and framing dimensions.
  • Page 5 – XDV Fireplace Dimensions - Installed as Top Vent
  • Page 6 – Clearance to Combustibles; Mantel Chart; Combustible mantel minimum installation.; Hearth; Mantel Shelf; Mantel from Top of Combustion Chamber
  • Page 7 – Input; Flange; Flange Location for; DO NOT; Certified To; Vented Gas Fireplace Heaters
  • Page 8 – INSTA VENT FREE; Typical gas supply installation.; Attach the wire to the ON/OFF switch and install; Remote switch wiring diagram for R models.; Alternate Switch Location; Alternate switch location.
  • Page 9 – This appliance may be fitted with a Synetek ignition; Electronic Gas Control Valve; POWER CORD; SIT822 Valve with Synetek electronic control wiring diagram.
  • Page 10 – Optional Top Vent Application; Secure outer collar adapter to unit with the round; Remove screws from outer collar adapter.; Connect the white wire from the wall switch or wall; Completed conversion.
  • Page 11 – Top Vent Application; 3XDV Restrictor Plate Installation; 3XDV restrictor plate installation.; General Venting; There must not be any obstruction; 6XDV restrictor plate installation.
  • Page 12 – General Venting Information - Termination Location; Canadian Installations
  • Page 13 – Termination clearances.; General Information Assembling Vent Pipes; Canadian Installations:; Flex Vent Pipes; Apply high temperature sealant to 4” and 7” pipes.; Outside Corner; Termination Clearances; with no side wall; of Caps
  • Page 14 – How to Use the Vent Graph; Horizontal dimension from the outside face of the; ertical dimension from the fl; Twist Lock Pipes
  • Page 15 – Rear Vent Top View; R E A R V E N T- T O P V I E W; Rear Wall Installation; When using flex vent, the opening will have to; Combustible Walls; Hole opening must; Vent Opening; Vent Opening for Combustible Wall; Locate vent opening on wall.; Adjustable zero clearance sleeve.
  • Page 16 – Side view of final unit location.; Rear Wall Vent Installations -; Follow Steps 1 and 2 on Page 15.; Grasp the vent pipe close to the collar and bend to; Vertical Sidewall Applications
  • Page 17 – If a 90° elbow is fitted directly on top of the fireplace; Maximum horizontal run with no rise.; According to the vent graph (Page 15) the; Horizontal run reduction.; Total angular variation = 270°; Maximum elbow usage.
  • Page 18 – Vertical Sidewall Installation
  • Page 19 – Vertical Sidewall Installation; next spring 5” (127 mm) from the previously installed; Horizontal length requirement.; Install spacer springs.; Install the 4” flex then 7” flex to the termination.; Bend flex vent at 90° so horizontal portion is 6
  • Page 20 – Below Grade Installations; Below grade installation.
  • Page 21 – Support straps for horizontal runs.; Attic Insulation Shield
  • Page 22 – Minimum termination to roof clearance.
  • Page 23 – Elbow; Vent components; Vent Components; Vent components; Venting Components; Venting Components; vent components
  • Page 24 – Care must be taken to avoid breakage of the glass.; Operating Instructions; Tilt window frame assembly out slightly at the bot-; Remove louvre assembly; Front of Unit; Ceramic hearth panel location.
  • Page 25 – Installation of Logs; LOGS; Log Identification Chart; Unpack the logs from packaging and remove each; As with all plastic bags - these are not toys
  • Page 26 – Place large lava rock onto the
  • Page 27 – Place ember material on top of
  • Page 28 – Refer to Figure 57 for bracket and bend loca-; Burner brackets and bends.; Place the log overlay. Hold the overlay
  • Page 29 – Place the log front left. Set the log
  • Page 30 – Large Lava Rock; Flame adjustment knob for SIT valve.; Flame adjustment knob for Honeywell valve.; LO; Honeywell Valve; Flame & Temperature Adjustment; Correct pilot flame appearance.; SIT Pilot; Inspecting the Venting System
  • Page 31 – Correct burner flame appearance.
  • Page 32 – FOR YOUR SAFETY READ BEFORE LIGHTING; WHAT TO DO IF YOU SMELL GAS; To Turn Off Gas To Heater; Lighting and Operating Instructions; Lighting Instructions; Euro SIT; Lighting instructions
  • Page 33 – Lighting & Operating Instructions; try to; BEFORE OPERATING; , smell all around the; What to do if you smell gas; For Your Safety, Read the Following Warnings; result, causing property damage, personal injury and loss of life.; Read the safety information above; try; Valve in the; “ON”; position
  • Page 34 – Instructions for RF Comfort Control Valve; Comfort control valve.; Shut Off Procedure; Transmitter diagram.
  • Page 35 – Fan; Comfort Valve wiring diagram.
  • Page 36 – LED Count; Auto Path
  • Page 37 – Local Path
  • Page 38 – SIT NOVA 820 MILLIVOLT VALVE; Troubleshooting the Gas Control System; SYMPTOM
  • Page 39 – Normal Operation
  • Page 40 – Fuel Conversion Instructions; Conversions must be completed by qualified personnel; Remove mounting screws, pressure regulator tower; SIT; Remove manifold assembly.
  • Page 41 – Front View; Remove air shutter from burner pan.; Remove screws holding burner housing assembly; Pilot Orifice Conversion; Burner orifice replacement.; Gas Conversion; Remove pilot orifice.
  • Page 42 – Installation Precautions; Conversion Procedure; do not; Depressd and turn center plunger.
  • Page 44 – Table 1 Injector Orifice Size Matrix
  • Page 45 – Burner and Burner Compartment; Cleaning the Standing; If repair is necessary, it should be per-; Maintenance
  • Page 48 – Fuel Conversion Kits
  • Page 49 – Optional Accessories Available; FK12 Fan Assembly; Method A; Fan Kits; Side View; FK12 Fan Kit placement.; WIRING DIAGRAM
  • Page 50 – Remote Controls; Model; ON/OFF and Temperature; IMTFK; Wall mounted thermostat control; Ceramic Refractory Panels; Installation Instructions; Rear ceramic panel placement.
  • Page 51 – Optional Trim Kits; Regular Trim Kit; Appliance Model; Screen Door Kit
  • Page 55 – BASIC WARRANTY; COMPONENT WARRANTY; IF WARRANTY SERVICE IS NEEDED...; ) Contact your supplier. Make sure you have your warranty,; LIMITED LIFETIME WARRANTY; PRODUCT COVERED BY THIS WARRANTY
  • Page 56 – Efficiency Ratings; CFM Corporation
Loading the manual

DO NOT STORE OR USE
GASOLINE OR OTHER
FLAMMABLE VAPORS AND
LIQUIDS IN THE VICINITY OF
THIS OR ANY OTHER
APPLIANCE.

WHAT TO DO IF YOU SMELL GAS:

•

Do not try to light any appliance.

•

Do not touch any electric switch;

do not use any phone in your

building.

•

Immediately call your gas

supplier from your neighbor’s

phone. Follow the gas suppliers

instructions.

•

If you cannot reach your gas

supplier call the fire department.

WARNING!

IF THE INFORMATION IN THIS
MANUAL IS NOT FOLLOWED
EXACTLY, A FIRE OR EXPLO-
SION MAY RESULT CAUSING
PROPERTY DAMAGE, PER-
SONAL INJURY OR LOSS OF
LIFE.

PLEASE READ THIS MANUAL
BEFORE INSTALLING AND
USING APPLIANCE

INSTALLER/CONSUMER

SAFETY INFORMATION

FOR YOUR SAFETY
Installation and service must
be performed by a qualified
installer, service agency or
the gas supplier.

Direct Vent Models:
33XDV, 36XDV, 39XDV

Installation Instructions and

Homeowner’s Manual

10009383 12/06 Rev. 10

C E R T I F I E D

DESIGN

�

CERTIFIED

INSTALLER: Leave this manual with the appliance.
CONSUMER: Retain this manual for future reference.

9383
XDV cover
5/06

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 2 - XDV Direct Vent Gas Fireplace; PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS; Table of Contents

XDV Direct Vent Gas Fireplace 2 10009383 PLEASE READ THE INSTALLATION & OPERATING INSTRUCTIONS BEFORE USING APPLIANCE. Thank you and congratulations on your purchase of a CFM Corporation fireplace.IMPORTANT: Read all instructions and warnings carefully before starting installation. Failure to fol...

Page 3 - OFF; PLEASE REVIEW THE FOLLOWING CAREFULLY; Locating Your Fireplace; Installation & Operating Instructions

10009383 3 XDV Direct Vent Gas Fireplace This gas appliance should be installed by a qualified installer in accordance with local building codes and with current CSA-B149.1 Installation codes for Gas Burning Appliances and Equipment. For USA Installations follow local codes and/or the current Nationa...

Page 4 - Framing Dimensions; XDV Fireplace Dimensions - Installed as Rear Vent; Fireplace specifications and framing dimensions.

XDV Direct Vent Gas Fireplace 4 10009383 Ref. 33XDV 36XDV 39 XDV A 33” (838 mm) 36” (914 mm) 39” (991 mm) B 28 ⁷⁄₈ ” (733 mm) 34 ¹⁄₄ ” (870 mm) 34 ¹⁄₄ ” (870 mm) C 31 ¹⁄₄ ” (794 mm) 34 ¹⁄₄ ” (870 mm) 37 ¹⁄₄ ” (946 mm) D 18 ³⁄₈ ” (466 mm) 23” (584 mm) 23” (584 mm) E 22 ³⁄₄ ” (578 mm) 24” (610 mm) 27”...

Other Vermont Casting Models

All Vermont Casting Other