US Stove Company 6110 - Manual

USSC 5 Fuel Considerations SHELLED CORN (Dry, preferably corn with 11% or less moisture content) • • • • • • • Optimum moisture content of corn should be 11% or less. Wet corn will rapidly deteriorate furnace components, reduce efficiency and void all warranties. Purchase a moisture tester if in dou...

6 USSC INSTALLATION OPTIONS Read this entire manual before you install and use your Multi-Fuel Furnace. Failure to follow instructionsmay result in property damage, bodily injury, or even death! (See specific installation details for clearances and other installation requirements) As a Primary Furna...

USSC 7 Installation CLEARANCES NOTE: Distance on the left-hand side of your Multi-Fuel Furnace is set at 24 inches for suitable access to the control panel and for fuel loading. This distance may be less, but not less than 7 inches.

8 USSC Installation VENTING REQUIREMENTS Install vent at clearances specified by the vent manufacturer. Do not connect the pellet vent to a vent serving any other appliance or furnace. Do not install a flue damper in the exhaust venting system of this unit. The following installation guidelines must...

USSC 9 Installation VENT TERMINATION CLEARANCES: A ----- Minimum 4-foot clearance below or beside any door or window that opens. B ----- Minimum 1-foot clearance above any door or window that opens. C ----- Minimum 3-foot clearance from any adjacent building. D ----- Minimum 7-foot clearance from an...

10 USSC Installation THROUGH THE WALL INSTALLATION (RECOMMENDED INSTALLATION) To vent the unit through the wall, connect the pipe adapter to the exhaust motor adapter. If the exhaust adapter is at least18-inches above ground level, a straight section of pellet vent pipe can be used through the wall....

USSC 11 Installation PRIMARY FURNACE SECONDARY (ADD-ON) FURNACE When installed as a seondary furnace, a Duct Damper must be installed between the air discharge of the Pellet furnaceand the primary (Gas, Electric, etc.). Damper must be a mechanical (spring return) style damper with a simple closure s...

12 USSC Do not operate your furnace with the viewing door open. The auger will not feed fuel under thesecircumstances and a safety concern may arise from sparks or fumes entering the room. A working smoke detector must be installed in the same room as this product. Hopper Lid must be closed during o...

USSC 13 Heat Range Room Fan Draft Fan Aux. Auto Manual CONTROL PANEL Turning the furnace OFF/ON, as well as adjustments for the fuel feed rateand room fan speed are performed by pressing the appropriate button(s)on the control panel which is located on the lower left-hand side of your American Harve...

14 USSC SHUT DOWN PROCEDURE Press the “OFF” button on the control panel to put the furnace in shut down mode. At this time, the red light above the “OFF” button will illuminate. Once this is done, the auger will stop feeding fuel, but the room air fan(s) and draft fan willcontinue to operate. When t...

USSC 15 Maintenance Operation DAILY OPERATION The hopper and furnace top will be hot during operation; therefore, you should always use some type ofhand protection when refueling your furnace. Never place your hand near the auger while the furnace is in operation. In the event of a power outage , th...

22 USSC Trouble Shooting PROBLEM CAUSE: Not enough combustion air; Fuel has too much moisture. Viewing window becoming black shortlyafter start-up. • Adjust the air damper to a more open position. • Use a fuel with less moisture content PROBLEM CAUSE: Not enough combustion air; Fuel has too much moi...

USSC 23 Error Codes Below is a chart describing the Error Codes that might be displayed if an error occurs with your furnace. Error Code Err1 Err2 Err3 Err4 Err5 Err6 Err7 Err8 ErrorDescrption The high limit temperature sensorhas tripped. Furnace ran out of fuel during normaloperation. The furnace w...

24 USSC THIS MANUAL WILL HELP YOU OBTAIN EFFICIENT, DEPENDABLE SERVICE FROM YOUR KING OR ASHLEY, AND ENABLE YOU TO ORDER REPAIR PARTS CORRECTLY. KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE. WHEN WRITING, ALWAYS GIVE THE FULL MODEL NUMBER WHICH IS ON THE NAMEPLATE ATTACHED TO THE HEATER. WH...