Tripp Lite DHUB - Manual

Tripp Lite DHUB – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1

2

3

4

5

6

7

8

9

10

11

12

Page: / 12 Go to

Next Page

PDF Text Table of Contents

Table of Contents:

• Page 2 – DSUT1CSU; SPECIFICATIONS
• Page 4 – LIFETIME LIMITED WARRANTY; TRIPP LITE
• Page 5 – Instalación; Desconecte el cable del equipo que desea proteger.
• Page 6 – ESPECIFICACIONES
• Page 8 – GARANTIA VITALICIA LIMITADA
• Page 9 – Déconnectez le câble à partir du matériel à protéger.
• Page 10 – CARACTÉRISTIQUES
• Page 11 – DTWINAX
• Page 12 – GARANTIE LIMITEÉ À VIE

Loading the manual

1

Network Dataline

Surge Suppressors

Español: p. 5

Français: p. 9

Tripp Lite Network Dataline Surge Suppressors are designed to protect data and communications
equipment against AC transients caused by lightning, electrostatic discharge and ground surges that
can enter equipment from the signal lines or chassis ground.

Tripp Lite Network Dataline Surge Suppressors described here protect virtually any pieces of net-
worked equipment using 100Base-T, 10Base-T, 10Base-2 and 10Base-5 Ethernet, Token Ring, RS232,
RS422/423/485, parallel, dial-up modems, fax, ISDN, DDS, T-1 and most other communication in-
terfaces.

Installation

1. Make sure the computer, network device or other equipment is logged OFF the network (if appli-
cable). Turn OFF power to the equipment.

2. Disconnect the cable from the equipment to be protected.

3. Connect the Tripp Lite Network Dataline Surge Suppressor directly to the equipment. DB9 and
DB25 models are reversible, to work with male or female ports. To change gender, remove the thumb-
screws, reverse their direction and reinstall.

4. Attach the green ground wire on the surge suppressor directly to the protected equipment’s chas-
sis. (Except DB9, DB15 and DB25 models.)

5. Reconnect the cable to the Tripp Lite Network Dataline Surge Suppressor.

NOTE!

The Tripp Lite Network Dataline Surge Suppressor must be properly grounded and positioned as
close as possible to the equipment to be protected. For best results, it is required that the length of the
signal line and ground wire (if equipped) between the surge suppressor and the protected equip-
ment be kept as short as possible, not to exceed 12 inches (12”). It is best to install the surge suppres-
sor directly to the equipment, as noted above.

NOTE!

Installing a typical Tripp Lite Network Dataline Surge Suppressor is equivalent to adding approxi-
mately three feet (3’) of typical data communication cable to a segment.

CAUTION!

The Tripp Lite Network Dataline Surge Suppressor does not protect the equipment on the opposite
end of the cable. Normally, protection at both ends is recommended.

CAUTION!

When properly installed, the Tripp Lite Network Dataline Surge Suppressor will only protect
against surges on the dataline portion of your installation. Simultaneous AC surge suppres-
sion/power protection in the form of an ISOBAR

®

surge suppressor or Tripp Lite UPS system

is strongly recommended for complete system/network protection and can also extend Ulti-
mate Lifetime Insurance coverage to connected equipment.

1111 W. 35th Street

Chicago, IL 60609 USA

Customer Service: (773) 869-1234

www.tripplite.com

Other Tripp Lite Models

• Tripp Lite N002-007-GY
  • Manual
• Tripp Lite N352-09M
  • Manual
• Tripp Lite AGSM700PSR3HG
  • Manual
• Tripp Lite OMNIVSINT1000
  • Manual
• Tripp Lite SUPDMB12KHW
  • Manual
• Tripp Lite BP480V40C
  • Manual
• Tripp Lite N506-02M
  • Manual
• Tripp Lite N201-020-RD
  • Manual
• Tripp Lite BP48V60RT3U
  • Manual
• Tripp Lite Rackmount Surge Suppressor/Line-Noise Filter
  • Manual