Tripp Lite DHUB-18V DHUB - Manual

Tripp Lite DHUB-18V DHUB – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1

2

3

4

5

6

7

8

9

10

11

12

Page: / 12 Go to

Next Page

PDF Text Table of Contents

Table of Contents:

• Page 2 – Specifications
• Page 4 – Warranty
• Page 5 – Instalación; Desconecte el cable del equipo a ser protegido.
• Page 6 – Especificaciones
• Page 8 – Garantía
• Page 9 – Installation; Déconnectez le câble de l'équipement qui doit être protégé.
• Page 10 – Spécifications
• Page 12 – Garantie

Loading the manual

1

Owner’s Manual

Network Dataline Surge Suppressors

Español: p. 5 • Français: p. 9

Installation

1. Make sure the computer, network device or other equipment is logged OFF the network (if

applicable). Turn OFF power to the equipment.

2. Disconnect the cable from the equipment to be protected.

3. Connect the Tripp Lite Network Dataline surge suppressor directly to the equipment. DB9

and DB25 models are reversible, to work with male or female ports. To change gender,
remove the thumbscrews, reverse their direction and reinstall.

4. Attach the green ground wire on the surge suppressor directly to the protected equipment’s

chassis. (Except DB9, DB15, DB25 and DUSB models.)

5. Reconnect the cable to the Tripp Lite Network Dataline surge suppressor.

NOTE!:

The Tripp Lite Network Dataline surge suppressor must be properly grounded and

positioned as close as possible to the equipment to be protected. For best results, it is required that
the length of the signal line and ground wire (if equipped) between the surge suppressor and the
protected equipment be kept as short as possible, not to exceed 12 inches (12"). It is best to install
the surge suppressor directly to the equipment, as noted above.

NOTE!:

Installing a typical Tripp Lite Network Dataline surge suppressor is equivalent to

addingapproximately three feet (3') of typical data communication cable to a segment.

CAUTION!

Tripp Lite Network Dataline surge suppressors do not protect the equipment on the
opposite end of the cable. Normally, protection at both ends is recommended.

CAUTION!

Tripp Lite Network Dataline surge suppressors will only protect against surges on
the dataline portion of your installation. Simultaneous AC surge suppression/power
protection in the form of an ISOBAR

®

surge suppressor or Tripp Lite UPS system is

strongly recommended for complete system/network protection and can also extend
Ultimate Lifetime Insurance coverage to connected equipment.

Tripp Lite Network Dataline surge suppressors are designed to protect data and communications
equipment against AC transients caused by lightning, electrostatic discharge and ground surges
that can enter equipment from the signal lines or chassis ground.

Select from the Tripp Lite Network Dataline surge suppressors described in this manual to
protect virtually any networked equipment connected to 100-Base-T, 10Base-T, 10Base-2 and
10-Base-5 Ethernet, Token Ring, RS232, RS422/423/485, parallel, dial-up modems, fax, ISDN,
DDS, T-1, USB or most any other communication interface.

200207034 93-2082 DUSB(DS4486) Owner’s Manual.qxd 8/22/2002 4:17 PM Page 1

Other Tripp Lite Models

• Tripp Lite N002-007-GY
  • Manual
• Tripp Lite N352-09M
  • Manual
• Tripp Lite AGSM700PSR3HG
  • Manual
• Tripp Lite OMNIVSINT1000
  • Manual
• Tripp Lite SUPDMB12KHW
  • Manual
• Tripp Lite BP480V40C
  • Manual
• Tripp Lite N506-02M
  • Manual
• Tripp Lite N201-020-RD
  • Manual
• Tripp Lite BP48V60RT3U
  • Manual
• Tripp Lite Rackmount Surge Suppressor/Line-Noise Filter
  • Manual