Tripp Lite Audio/Video On-Line UPS System - Manual

Page 2 - UPS Location Warnings; dust or direct sunlight.; UPS Connection Warnings; UPS into itself this will damage the UPS.; Equipment Connection Warnings; event of a blackout or other power interruptions.; SAVE THESE INSTRUCTIONS; Important Safety Instructions

UPS Location Warnings • Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust or direct sunlight. • For best performance, keep the indoor temperature between 32º F and 104º F (0º C and 40º C).• Leave adequate space around all sides of the UPS for proper ventilati...

Page 3 - Installation

Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see next page for 2-post mounting). The user must determine the fitness of hardware and procedures beforemounting. If hardware and procedures are not suitable for your application, contact themanufacturer of your rack or rack ...

Page 4 - Tower Mounting

4 Installation (continued) 2-Post Mounting If you mount the UPS in a 2-post rack, it requires the addition of a Tripp Lite 2-PostRackmount Installation Kit (model: 2POSTKITRMWM, sold separately). See Installation Kitowner’s manual for installation procedure for 2U UPS models. Tower Mounting Your UPS...

Page 5 - Plug your equipment into your UPS.; a beep

5 Important Safety Instructions Connection and Start-Up Plug your UPS’s line cord into anelectrical outlet. Your UPS must be connected to a dedicatedcircuit of sufficient amperage. Note, however,that the select models may be fitted withdifferent plug types. Refer to the “OP Rating/Plug Rating” chart...

Page 6 - Use the included USB cable (see; EPO Port Connection; The EPO port is not a; External Battery Connection

6 Optional Connections (continued) USB and RS-232 SerialCommunications Use the included USB cable (see ) and/or DB9 serial cable (see ) to connect the UPS to a Media Center PC, home automationsystem or server. Install the Tripp LitePowerAlert Software appropriate to yourequipment's operating system....

Page 7 - This switch controls four separate UPS functions:; Basic Operation

7 Front Panel Switches “ON/TEST” Button: This switch controls four separate UPS functions: UPS Power ON To turn the UPS on, press this button, hold it for several seconds untilyou hear a beep, then release it. The “ON LINE” LED will illuminate. UPS Self-Test During normal on-line operation, press th...

Page 8 - “LOAD ACTIVE METER” LED:

8 Front Panel Indicator Lights continued “BYPASS” LED: This yellow light will flash to indicate that the UPS’s DC/AC inverter is deactivated and the UPS is in the “Bypass”mode. During normal operation this LED will light briefly when theunit is plugged in, but if an internal fault or overload occurs...

Page 9 - External Battery Pack Connector (configuration varies by model):

9 Rear Panel “REPLACE BATT” LED: This red light will illuminate constantly and the UPS alarm will beep every 2 seconds if your UPS’smicroprocessor detects a battery fault or if your UPS fails theautomatic self-test (after you turn your UPS ON) and the UPS batteryis less than fully charged. Let the U...

Page 10 - This permanently attached power cord connects your

Rear Panel continued Input Cord: This permanently attached power cord connects your UPS to a power outlet. AC Receptacles (Varied by Model): These 15-, 20- and 30-amp receptacles provide your connected equipment with pure sine-waveAC output from the AC line during normal operation and from batterypo...

Page 11 - Troubleshooting

11 The UPS’s control panel lights will turn on in the sequences below to signal that the UPS ishaving operational difficulties. Lights (On/Flashing) and Condition Solution On: REPLACE BATT Let the UPS system charge for at least Condition: Replace Battery 12 hours and perform a self test using the &#...

Page 13 - Battery Replacement; Procedure; Add Batteries

13 Battery Replacement Under normal conditions, the original batteries in your UPS will last many years. See Safetysection before replacing batteries. The batteries are designed for hot-swap replacement (i.e.leaving the UPS in ON mode), but some qualified service personnel may wish to put the UPSin ...

Page 14 - Storage and Service; Warranty Registration

Visit www.tripplite.com/warranty today to register the warranty for your new Tripp Lite product. You'll be automatically entered into adrawing for a chance to win a FREE Tripp Lite product!* * No purchase necessary. Void where prohibited. Some restrictions apply. See website for details. Regulatory ...

Tripp Lite Audio/Video On-Line UPS System - Manual

Table of Contents:

Summary

Other Tripp Lite Models