Tripp Lite 93-2486 - Manual

Page 2 - UPS Location Warnings; dust or direct sunlight.; UPS Connection Warnings; UPS into itself this will damage the UPS.; Equipment Connection Warnings; Important Safety Instructions

UPS Location Warnings • Install your UPS indoors, away from excess moisture or heat, conductive contaminants, dust or direct sunlight. • For best performance, keep the indoor temperature between 32º F and 104º F (0º C and 40º C). • Leave adequate space around all sides of the UPS for proper ventilat...

Page 3 - Mounting Rack; Installation

Mount your equipment in either a 4-post or 2-post rack or rack enclosure (see next page for 2-post mounting). The user must determine the fitness of hardware and procedures beforemounting. If hardware and procedures are not suitable for your application, contact themanufacturer of your rack or rack ...

Page 4 - . Repeat with additional cords to

INPUT BREAKER INPUT BREAKER ACC. SLOT LOAD 1 IN PHONE / DATA PROTECTION OUT EPO LOAD 2 OUTP RS-232 USB CAUTION Risk of electric shSee top of unit focautionary markin Your model may differ. 1 2a Your model may differ. 4 Installation (continued) 2-Post (Telecom) Mounting If you mount 2U UPS models in ...

Page 5 - • Press the ON/TEST Switch and hold it for; Optional Connections

5 Important Safety Instructions Connection and Start-Up (continued) Turn the UPS ON: • Press the ON/TEST Switch and hold it for several seconds until you hear a beep • Release the ON/TEST Switch. The ON LINE LED will illuminate, and your UPS will begin providing power to its AC outlets Note: After i...

Page 6 - Use the included USB cable (see; EPO Port Connection; The EPO port is not a phone line surge; External Battery Connection

6 Optional Connections (continued) USB and RS-232 SerialCommunications Use the included USB cable (see ) and/or DB9 serial cable (see ) to connect the communication port of your computer to thecommunication port of your UPS. Install onyour computer the Tripp Lite PowerAlertSoftware appropriate to yo...

Page 7 - Front Panel Switches; This switch controls four separate UPS functions:; Front Panel Indicator Lights; Basic Operation

7 Front Panel Switches “ON/TEST” Button: This switch controls four separate UPS functions: UPS Power ON To turn the UPS on, press this button, hold it for several seconds untilyou hear a beep, then release it. The “ON LINE” LED will illuminate. UPS Self-Test During normal on-line operation, press th...

Page 8 - “LOAD ACTIVE METER” LED:

8 Front Panel Indicator Lights continued “BYPASS” LED: This yellow light will flash to indicate that the UPS’s DC/AC inverter is deactivated and the UPS is in the “Bypass”mode. During normal operation this LED will light briefly when theunit is plugged in, but if an internal fault or overload occurs...

Page 9 - Rear Panel; External Battery Pack Connector (configuration varies by model):

9 Rear Panel “REPLACE BATT” LED: This red light will illuminate constantly and the UPS alarm will beep every 2 seconds if your UPS’smicroprocessor detects a battery fault or if your UPS fails theautomatic self-test (after you turn your UPS ON) and the UPS batteryis less than fully charged. Let the U...

Page 10 - Input Cord Connection:; These ports connect your; Communications

Rear Panel continued Input Cord Connection: This IEC320-C20 or IEC320-C14 inlet enables the UPS to be connected to an AC power source via a user-supplied cord with country-specific plug. See "Connection andStart-Up". AC Receptacles (Varied by Model): These receptacles provide your connected ...

Page 11 - Troubleshooting

11 The UPS’s control panel lights will turn on in the sequences below to signal that the UPS ishaving operational difficulties. Lights (On/Flashing) and Condition Solution On: REPLACE BATT Let the UPS system charge for at least Condition: Replace Battery 12 hours and perform a self test using the &#...

Page 13 - Battery Replacement; Procedure; Add Batteries

13 Battery Replacement Under normal conditions, the original batteries in your UPS will last many years. See"Important Safety Instructions" before replacing batteries. The batteries are designed for hot-swap replacement (i.e. leaving the UPS in ON mode), but some qualified service personnel ...

Page 14 - Storage and Service; Storage

Regulatory Compliance Identification Numbers: For the purpose of regulatory compliance certifications and identification, your Tripp Lite product has been assigned a unique series number. The series number can be found on the product nameplate label, along withall required approval markings and info...

Tripp Lite 93-2486 - Manual

Table of Contents:

Summary

Other Tripp Lite Models