Page 2 - • S L A S H V X L; INTRODUCTION; Brushless Power System. The Velineon Power System; Traxxas Support; TABLE OF CONTENTS
2 • S L A S H V X L INTRODUCTION Thank you for purchasing the Slash VXL equipped with the Velineon ® Brushless Power System. The Velineon Power System lets you experience the best that brushless motor technology has to offer. Incredible speed, efficient operation, long run times, and low-maintenance...
Page 3 - S L A S H V X L • 3; BEFORE YOU PROCEED; Your hobby; Refers you to a page with a related topic.; SUPPORT
S L A S H V X L • 3 BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. Before running your model, look over this entire manual and ...
Page 4 - • S L A S H V X L; SAFETY PRECAUTIONS; IMPORTANT POINTS TO REMEMBER; Most importantly, use good common sense at all times.; BATTERIES AND BATTERY CHARGING; Recycling Your Traxxas Power Cell NiMH Battery; LiPo batteries are intended only for advanced users; Traxxas does not; Be aware; your local hobby dealer or contact the battery manufacturer.; batteries should be recycled at the end of their useful life.; SPEED CONTROL
4 • S L A S H V X L This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. Gearing and battery choice ( see LiPo Batteries, right) effect the skill level of the model. See chart below. All instructions and precautions ou...
Page 5 - S L A S H V X L • 5; TOOLS, SUPPLIES AND REQUIRED EQUIPMENT; Recommended Equipment; Use the Right; Supplied Tools and Equipment
S L A S H V X L • 5 TOOLS, SUPPLIES AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. Recommended Equipment These items are not required for the operation of your mo...
Page 6 - • S L A S H V X L; ANATOMY OF THE SLASH VXL
6 • S L A S H V X L ANATOMY OF THE SLASH VXL Motor (Velineon 3500) Transmission Spur Gear (under gear cover) Pinion Gear (under gear cover) Rear Bumper Slipper Clutch (under gear cover) Electronic Speed Control (VXL-3s) Battery Compartment Battery Nerf Bar Battery Hold-Down Receiver Box LED Light Pi...
Page 7 - S L A S H V X L • 7; QUICK START: GETTING UP TO SPEED; Make sure the steering servo is working correctly.
S L A S H V X L • 7 QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions on page 4 6. Check servo operation • See page 14 For your...
Page 8 - • S L A S H V X L; TRAXXAS TQ; Applying the Decals
8 • S L A S H V X L TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM Applying the Decals The main decals for your model have been applied at the factory. The decals are printed on self-adhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it fr...
Page 9 - S L A S H V X L • 9; IMPORTANT RADIO SYSTEM PRECAUTIONS; Correct
S L A S H V X L • 9 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM NiMH - Abbreviation for nickel-metal hydride. Rechargeable NiMH batteries offer high current handling, and much greater resistance to the “memory” effect. NiMH batteries generally allow ...
Page 10 - Your model is equipped with the newest TQi 2.4GHz transmitter; MODEL WIRING DIAGRAM; to Motor; VXL-3s ELECTRONIC SPEED CONTROL; to Battery; TRANSMITTER AND RECEIVER; 0 • S L A S H V X L
CH1 CH1 CH2 CH3 CH4 RPM V/T BATT/ CH5 CH1 CH1 CH2 CH3 CH4 RPM V/T BATT / CH5 SS ++ -- V/T - Voltage/Temp Senor Port ** RPM - RPM Sensor Port** BATT/ CH5 - Battery/Channel 5* CH4 - Channel 4* CH3 - Channel 3* CH2 - Speed Control CH1 - Steering Servo CH1 - Channel 1* * Not used ** Accessory sensor por...
Page 11 - S L A S H V X L • 11; INSTALLING TRANSMITTER BATTERIES; It is normal for the; Using Other Chargers; is a 4 amp charger and will charge; Use the Right Batteries
S L A S H V X L • 11 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM INSTALLING TRANSMITTER BATTERIES Your TQi transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. 1. Remove the battery compartment door by pressing the tab and sliding the door open. 2. I...
Page 12 - 2 • S L A S H V X L; • Height with stock strap:; INSTALLING THE BATTERY PACK; Using Different Battery Configuration; Using Other Batteries; NiMH stick pack setup
12 • S L A S H V X L TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM 4 The following Traxxas High Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector. Battery Compartment Specs:• 166mm (6.54 " ) l...
Page 13 - S L A S H V X L • 13; RADIO SYSTEM RULES; Weak batteries will limit the radio signal between the; RADIO SYSTEM BASIC ADJUSTMENTS; Throttle Neutral Adjustment; Turn to ESC Setup Programming on; Steering Trim; RADIO SYSTEM CONTROLS
S L A S H V X L • 13 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM 5 Remember, always turn the TQ transmitter on first and off last to avoid damage to your model. Automatic Fail-Safe The TQi transmitter and receiver are equipped with an automatic fail-safe system that does not require user programm...
Page 14 - 4 • S L A S H V X L; USING THE RADIO SYSTEM
14 • S L A S H V X L TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. USING THE RADIO SYSTEM Th...
Page 15 - S L A S H V X L • 15; Press and hold the receiver’s LINK button as you switch on the; Decreased Steering Sensitivity (Negative Exponential); SETTING UP THE ANTENNA; Do not bend or kink
S L A S H V X L • 15 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM 2. Press and hold the receiver’s LINK button as you switch on the speed control by pressing the EZ-Set button. 3. When the transmitter and receiver’s LEDs turn solid green, the system is bound and ready for use. Confirm that the ste...
Page 16 - 6 • S L A S H V X L; ADJUSTING THE ELECTRONIC SPEED CONTROL; VXL-3s Specifications; None; Never use LiPo; When the LED blinks RED ONCE, pull the throttle
16 • S L A S H V X L ADJUSTING THE ELECTRONIC SPEED CONTROL VXL-3s Specifications Input voltage: 4.8-11.1V (4 to 9 cells NiMH or 2S to 3S LiPo) Supported Motors: BrushedBrushlessSensorless brushless Motor limit: None Continuous current: 200A Peak current : 320A BEC voltage: 6.0V DC Transistor type: ...
Page 17 - S L A S H V X L • 17; Tip For Fast Mode Changes; See page 23 for Advanced VXL-3s features.
S L A S H V X L • 17 ADJUSTING THE ELECTRONIC SPEED CONTROL Patent-Pending Training Mode (Profile #3) reduces forward and reverse throttle by 50%. Training Mode is provided to reduce the power output allowing beginning drivers to better control the model. As driving skills improve, simply change to ...
Page 18 - 8 • S L A S H V X L; About Run Time; RUNNING IN WET CONDITIONS; DRIVING YOUR MODEL
18 • S L A S H V X L Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs. This is particularly important whe...
Page 19 - S L A S H V X L • 19; Not all batteries can be used in wet environments.
S L A S H V X L • 19 Water resistance applies only to the installed electronic components. Running in wet conditions requires additional care and maintenance for the mechanical and electrical components to prevent corrosion of metal parts and maintain their proper function. Precautions• Without prop...
Page 20 - 0 • S L A S H V X L; RECEIVER BOX: MAINTAINING A WATERTIGHT SEAL
20 • S L A S H V X L 9. Additional Maintenance : Increase your frequency of disassembly, inspection and lubrication of the following items: This is necessary after extended wet use or if the vehicle will not be used for an extended period of time (such as a week or longer). This additional maintenan...
Page 21 - S L A S H V X L • 21; ADJUSTING YOUR MODEL; Adjusting the Camber; Place the rear shocks in position 2; Rear Camber; Front
S L A S H V X L • 21 ADJUSTING YOUR MODEL Once you become familiar with driving your model, you might need to make adjustments for better driving performance Adjusting the Toe-in Geometry and alignment specs play an important roll in your model’s handling. Take the time to set them correctly. Set th...
Page 22 - 2 • S L A S H V X L; For this type of driving, smaller pinion gears are
22 • S L A S H V X L To achieve a good starting point for the slipper clutch, tighten the slipper clutch adjusting nut clockwise until the slipper clutch adjusting spring fully collapses (do not over tighten), and then turn the slipper clutch nut counter-clockwise one full turn. Do not run your mode...
Page 23 - S L A S H V X L • 23; Adjusting Gear Mesh; Turn the transmitter power switch on. Make certain the; ADVANCED VXL-3s ESC SETUP; Sensorless Brushless Motors; Sensorless brushless
S L A S H V X L • 23 Adjusting Gear Mesh Incorrect gear mesh is the most common cause of stripped spur gears. Gear mesh should be checked and adjusted anytime a gear is replaced. To set the gear mesh, cut a narrow strip of notebook paper and run it into the gear mesh. Loosen the motor screws and sli...
Page 24 - 4 • S L A S H V X L; Brushed Motors; TEMPERATURES AND COOLING; Temperature gauge; LIPO BATTERIES
24 • S L A S H V X L Brushed Motors For the ultimate in versatility, the VXL-3s has no motor limit when used with a brushed motor. This allows you to use any readily available 540 or 550 size brushed motors in your VXL-3s equipped vehicle. Always be sure to follow all break in and maintenance instru...
Page 25 - S L A S H V X L • 25; MAINTAINING YOUR MODEL
S L A S H V X L • 25 1 0 Always wear eye protection when using compressed air or spray cleaners and lubricants. MAINTAINING YOUR MODEL Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously. Inspect the vehicle for ob...
Page 26 - 6 • S L A S H V X L; clockwise to its stop will eliminate all brake action).; TRAXXAS LINK MODEL MEMORY; Restoring Factory Defaults; TQ
26 • S L A S H V X L Your Traxxas transmitter has a programmable Multi-Function knob that can be set to control various advanced transmitter functions (set to Steering Sensitivity by default, see page 15). Accessing the programming menu is done by using the menu and set buttons on the transmitter an...
Page 27 - S L A S H V X L • 27; Model Lock; Press and hold MENU to return to driving mode.; Note; : To unlock a memory, press SET twice at step 5. The LED will; Failsafe; TRANSMITTER LED CODES
S L A S H V X L • 27 TQ i ADVANCED TUNING GUIDE Model Lock The Traxxas Link Model Memory feature can store up to twenty models (receivers) in its memory. If you bind a twenty-first receiver, Traxxas Link Model Memory will delete the “oldest” receiver from its memory (in other words, the model you us...
Page 28 - 8 • S L A S H V X L; Enter Programming; MENU TREE; Dual Rate has been selected.
28 • S L A S H V X L Press MENU to move through options. Press SET to select an option. Press MENU to move through options. Press SET to select an option. Press SET to select an option. Enter Programming Press and hold MENU for 3 seconds Steering Sensitivity (Expo) One Blink Red 1 Electric One Blink...
Page 29 - S L A S H V X L • 29; MENU TREE FORMULAS
S L A S H V X L • 29 TQ i ADVANCED TUNING GUIDE Set Multi-Function knob for STEERING SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks x 8 Press SET to confirm green LED blinks (x8) Press/hold MENU returns to driving mode Set Multi-Function knob for THROTTLE SENSITIVITY (E...
Page 30 - 0 • S L A S H V X L; PROGRAMMING YOUR TQ; or iPod touch; Traxxas Link; Tap and slide to adjust Steering Sensitivity,
30 • S L A S H V X L “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod and iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this dev...
Page 31 - S L A S H V X L • 31; NOTES
