Page 2 - • S L A S H 4 x 4; INTRODUCTION; Brushless Power System. The Velineon Power System; Traxxas Support; TABLE OF CONTENTS
2 • S L A S H 4 x 4 INTRODUCTION Thank you for purchasing the Slash 4X4 equipped with the Velineon ® Brushless Power System. The Velineon Power System lets you experience the best that brushless motor technology has to offer. Incredible speed, efficient operation, long run times, and low-maintenance...
Page 3 - S L A S H 4 x 4 • 3; BEFORE YOU PROCEED; Your hobby; Refers you to a page with a related topic.; SUPPORT
S L A S H 4 x 4 • 3 BEFORE YOU PROCEED Carefully read and follow all instructions in this and any accompanying materials to prevent serious damage to your model. Failure to follow these instructions will be considered abuse and/or neglect. Before running your model, look over this entire manual and ...
Page 4 - • S L A S H 4 x 4; SAFETY PRECAUTIONS; IMPORTANT POINTS TO REMEMBER; Most importantly, use good common sense at all times.; BATTERIES AND BATTERY CHARGING; Recycling Your Traxxas Power Cell NiMH Battery; LiPo batteries are intended; Traxxas does not recommend that anyone under the age of 16 use or; Be aware; your local hobby dealer or contact the battery manufacturer.; batteries should be recycled at the end of their useful life.; SPEED CONTROL
4 • S L A S H 4 x 4 This model is not intended for use by children under 14 years of age without the supervision of a responsible and knowledgeable adult. Gearing and battery choice ( see LiPo Batteries, right) effect the skill level of the model. See chart below. All instructions and precautions ou...
Page 5 - S L A S H 4 x 4 • 5; TOOLS, SUPPLIES AND REQUIRED EQUIPMENT; Recommended Equipment; Use the Right; Supplied Tools and Equipment
S L A S H 4 x 4 • 5 TOOLS, SUPPLIES AND REQUIRED EQUIPMENT Your model comes with a set of specialty metric tools. You’ll need to purchase other items, available from your hobby dealer, to operate and maintain your model. Recommended Equipment These items are not required for the operation of your mo...
Page 6 - ANATOMY OF THE SLASH 4X4
6 • SLASH 4x4 ANATOMY OF THE SLASH 4X4 Motor (Velineon 3500) Spur Gear Pinion Gear Rear Bumper Slipper Clutch Electronic Speed Control (VXL-3s) Battery Compartment LED Light Pipe Nerf Bar Battery Hold-Down Battery Receiver Box Antenna Mount Front Suspension Arm Front Bumper Steering Servo Shock (Oil...
Page 7 - S L A S H 4 x 4 • 7; QUICK START: GETTING UP TO SPEED; Make sure the steering servo is working correctly.
S L A S H 4 x 4 • 7 QUICK START: GETTING UP TO SPEED The following guide is an overview of the procedures for getting your model running. Look for the Quick Start logo on the bottom corners of Quick Start pages. 1. Read the safety precautions on page 4 6. Check servo operation • See page 14 For your...
Page 8 - • S L A S H 4 x 4; TRAXXAS TQ; Applying the Decals
8 • S L A S H 4 x 4 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM Applying the Decals The main decals for your model have been applied at the factory. The decals are printed on self-adhesive clear mylar and are die-cut for easy removal. Use a hobby knife to lift the corner of a decal and lift it fr...
Page 9 - S L A S H 4 x 4 • 9; IMPORTANT RADIO SYSTEM PRECAUTIONS; Correct
S L A S H 4 x 4 • 9 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM Good charging procedures are required to reduce the possibility of developing a “memory” effect and shortened run times. NiMH - Abbreviation for nickel-metal hydride. Rechargeable NiMH b...
Page 10 - Your model is equipped with the newest TQi 2.4GHz transmitter; MODEL WIRING DIAGRAM; to Motor; VXL-3s ELECTRONIC SPEED CONTROL; to Battery; TRANSMITTER AND RECEIVER; ESC/Motor Wiring Diagram
CH1 CH1 CH2 CH3 CH4 RPM V/T BATT/ CH5 CH1 CH1 CH2 CH3 CH4 RPM V/T BATT / CH5 SS ++ -- V/T - Voltage/Temp Senor Port ** RPM - RPM Sensor Port** BATT/ CH5 - Battery/Channel 5* CH4 - Channel 4* CH3 - Channel 3* CH2 - Speed Control CH1 - Steering Servo CH1 - Channel 1* * Not used ** Accessory sensor por...
Page 11 - INSTALLING TRANSMITTER BATTERIES; It is normal for the; Using Other Chargers; is a 4 amp charger and will charge; Use the Right Batteries
S L A S H 4 x 4 • 11 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM INSTALLING TRANSMITTER BATTERIES Your TQi transmitter uses 4 AA batteries. The battery compartment is located in the base of the transmitter. 1. Remove the battery compartment door by pressing the tab and sliding the door open. 2. I...
Page 12 - • Height with stock strap:; INSTALLING THE BATTERY PACK; Using Different Battery Configuration; Using Other Batteries; 5mm side: Standard NiMH stick pack
12 • S L A S H 4 x 4 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM 4 The following Traxxas High Current Connector packages are available from your hobby dealer. When using adapters, be careful not to exceed the current rating of the Molex connector. Battery Compartment Specs:• 166mm (6.54 " ) l...
Page 13 - RADIO SYSTEM RULES; Throttle Neutral Adjustment; Turn to ESC Setup Programming on; Steering Trim; RADIO SYSTEM CONTROLS
S L A S H 4 x 4 • 13 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM 5 Remember, always turn the TQi transmitter on first and off last to avoid damage to your model. Automatic Fail-Safe The TQi transmitter and receiver are equipped with an automatic fail-safe system that does not require user program...
Page 14 - USING THE RADIO SYSTEM; Never use LiPo batteries while
14 • S L A S H 4 x 4 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM Using Reverse: While driving, push the throttle trigger forward to apply brakes. Once stopped, return the throttle trigger to neutral. Push the throttle trigger forward again to engage proportional reverse. USING THE RADIO SYSTEM Th...
Page 15 - Press and hold the receiver’s LINK button as you switch on the; Decreased Steering Sensitivity (Negative Exponential); SETTING UP THE ANTENNA; Do not bend or kink the antenna wire! See the side
S L A S H 4 x 4 • 15 TRAXXAS TQ i RADIO & VELINEON POWER SYSTEM 2. Press and hold the receiver’s LINK button as you switch on the speed control by pressing the EZ-Set button. 3. When the transmitter and receiver’s LEDs turn solid green, the system is bound and ready for use. Confirm that the ste...
Page 16 - ADJUSTING THE ELECTRONIC SPEED CONTROL; VXL-3s Specifications; None; Never use LiPo; When the LED blinks RED ONCE, pull the throttle
16 • S L A S H 4 x 4 ADJUSTING THE ELECTRONIC SPEED CONTROL VXL-3s Specifications Input voltage: 4.8-11.1V (4 to 9 cells NiMH or 2S to 3S LiPo) Supported Motors: BrushedBrushlessSensorless brushless Motor limit: None Continuous current: 200A Peak current : 320A BEC voltage: 6.0V DC Transistor type: ...
Page 17 - Tip For Fast Mode Changes; See page 24 for Advanced VXL-3s features.
S L A S H 4 x 4 • 17 ADJUSTING THE ELECTRONIC SPEED CONTROL Patent-Pending Training Mode (Profile #3) reduces forward and reverse throttle by 50%. Training Mode is provided to reduce the power output allowing beginning drivers to better control the model. As driving skills improve, simply change to ...
Page 18 - DRIVING YOUR MODEL; About Run Time; manufacturer of your batteries and charger.; mAh Ratings and Power Output; RUNNING IN WET CONDITIONS; Not all batteries can be used in wet environments.; Consult your battery; Before Running Your Vehicle in Wet Conditions
18 • SLASH 4x4 DRIVING YOUR MODEL Now it’s time to have some fun! This section contains instructions on driving and making adjustments to your model. Before you go on, here are some important precautions to keep in mind. • Allow the model to cool for a few minutes between runs. This is particularly ...
Page 19 - RECEIVER BOX: MAINTAINING A WATERTIGHT SEAL
SLASH 4x4 • 19 tires if holes are not cut in the tires. Cut two small holes (3mm or 1/8” diameter) in each tire. Each hole should be near the tire center-line, 180 degrees apart. 3. Confirm that the RX box O-ring and cover are installed correctly and secure. Make sure the screws are tight and the bl...
Page 20 - BASIC TUNING ADJUSTMENTS; Camber; -degree negative camber each side
20 • S L A S H 4 x 4 Once you become familiar with driving your model, you might need to make adjustments for better driving performance Adjusting Gear Mesh Incorrect gear mesh is the most common cause of stripped spur gears. Gear mesh should be checked and adjusted anytime a gear is replaced. Acces...
Page 21 - Turn the transmitter power switch on. Make certain the; Adjusting the Slipper Clutch
S L A S H 4 x 4 • 21 3 on the rear suspension arms). If you plan on driving on hard surfaces the following changes should be made:1. Move the front shocks to position 3 on the suspension arms. 2. Move the rear shocks to position 4 or 5 on the suspension arms. 3. Add a 4mm preload spacer to the front...
Page 22 - MAINTAINING YOUR MODEL; The following procedures should be taken very seriously.
22 • S L A S H 4 x 4 MAINTAINING YOUR MODEL Your model requires timely maintenance in order to stay in top running condition. The following procedures should be taken very seriously. Frequently inspect the vehicle for obvious damage or wear. Look for: 1. Cracked, bent, or damaged parts 2. Check the ...
Page 23 - ADVANCED TUNING ADJUSTMENTS; CAMBER GAIN; • Front Camber Gain; ROLL CENTER; • Front Roll Center; - “Bump steer” refers to; • Rear Roll Center; To raise the roll center; GEARING; Front; Gearing Compatibility Chart:
S L A S H 4 x 4 • 23 ADVANCED TUNING ADJUSTMENTS CAMBER GAIN Slash 4x4 has provisions for adjusting the camber gain geometry of the front and rear suspension. “Camber gain” refers to an increase in camber angle as the suspension is compressed. The camber gain of the vehicle can be changed by moving ...
Page 24 - Check and adjust gear mesh if a spur and/or pinion gear is changed.; LIPO BATTERIES; Sensorless brushless
24 • S L A S H 4 x 4 ADVANCED TUNING ADJUSTMENTS When using higher gear ratios, it is important to monitor the temperatures of the battery and motor. If the battery is extremely hot (150°F), and/or the motor is too hot to touch (200°F), your model is probably over-geared and drawing too much current...
Page 25 - Optional brushed motor wiring diagram; TEMPERATURES AND COOLING; Temperature gauge; TUNING THE SEALED GEAR DIFFERENTIALS; Remove the two 3x15mm button-head screws that secure the
S L A S H 4 x 4 • 25 automatically detects what kind of motor it is connected to so no programming actions are required to use brushed motors. Simply be sure to properly connect the motor to the speed control as shown. Optional brushed motor wiring diagram : • Motor positive (+) should be connected ...
Page 26 - Refilling the differential:; Front Differential Removal; Front of Truck
26 • S L A S H 4 x 4 4. Remove 3x15mm button-head screw from diff tie bar. 5. Slide tie bar off truck. 6. Remove two 3x15mm button-head screws from diff cover. Do not remove the two screws that secure the shock tower. 7. Use a 1.5mm hex wrench to remove the two screw pins that hold the driveshaft yo...
Page 27 - clockwise to its stop will eliminate all brake action).; TRAXXAS LINK MODEL MEMORY; TQ; Restoring Factory Defaults
S L A S H 4 x 4 • 27 Your Traxxas transmitter has a programmable Multi-Function knob that can be set to control various advanced transmitter functions (set to Steering Sensitivity by default, see page 15). Accessing the programming menu is done by using the menu and set buttons on the transmitter an...
Page 28 - Model Lock; Press and hold MENU to return to driving mode.; Note; : To unlock a memory, press SET twice at step 5. The LED will; Failsafe; TRANSMITTER LED CODES
28 • S L A S H 4 x 4 TQ i ADVANCED TUNING GUIDE Model Lock The Traxxas Link Model Memory feature can store up to thirty models (receivers) in its memory. If you bind a thirty-first receiver, Traxxas Link Model Memory will delete the “oldest” receiver from its memory (in other words, the model you us...
Page 29 - Enter Programming; When you enter a menu, you always start at the; MENU TREE; Dual Rate has been selected.
SLASH 4x4 • 29 Press MENU to move through options. Press SET to select an option. Press MENU to move through options. Press SET to select an option. Press SET to select an option. Enter Programming Press and hold MENU for 3 seconds Steering Sensitivity (Expo) One Blink Red 1 Electric One Blink Red 1...
Page 30 - MENU TREE FORMULAS
TQ i ADVANCED TUNING GUIDE Set Multi-Function knob for STEERING SENSITIVITY (Expo) Press/hold MENU green LED blinks Press SET red LED blinks x 8 Press SET to confirm green LED blinks (x8) Press/hold MENU returns to driving mode Set Multi-Function knob for THROTTLE SENSITIVITY (Expo) Press/hold MENU ...
Page 31 - PROGRAMMING YOUR TQ; or iPod touch; Traxxas Link; Tap and slide to adjust Steering Sensitivity,
S L A S H 4 x 4 • 31 “Made for iPod” and “Made for iPhone” mean that an electronic accessory has been designed to connect specifically to iPod and iPhone, respectively, and has been certified by the developer to meet Apple performance standards. Apple is not responsible for the operation of this dev...
