Toro ESC - User Manual
Toro ESC – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Move the gate manually until interlocked in the motor.; General connections; DC bus LED
- Page 3 – Turning direction change and check (; rSXX; Display indications
- Page 4 – Total opening radio code programming; Select the option; Pedestrian opening radio code programming,; instead of; Start slowdown by pressing the; Pedestrian opening; is programmed using the parameter; Clutch adjustment
- Page 5 – Complete programming chart
7
TORO-I
Quick installation and programming guide
English
WARNING
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The most recent versions of this guide and the
installation manual are available at the "Downloads" section on Erreka's website.
http://www.erreka-automation.com
The options and functions described in this guide apply for the firmware version indicated on the circuit. The
firmware, as part of a process of continuous improvement, is subject to new functionalities or upgrades being
included as a result of new versions which are not necessarily compatible with previous ones. For this reason,
some options or functions may differ or be unavailable if your firmware is older than shown in this guide.
E295A
SG.C
SG.C
SG.C
SG.C
SG.A
C295B
Elements of the complete installation
Assembly levels (mm)
Photocells
SG.A
: opening photocell,
enable:
C410
enable testing:
C411
SG.C:
closing photocell,
enable:
C510
enable testing:
C511
enable with opening
disabled:
C520
enable testing with
opening disabled:
C521
ELECTRICAL WIRING:
Element
Nº wires x section
Maximum
length
A: Main power supply
3x1.5mm
2
30m
B: Flashing light
2x0.5mm
2
20m
C: Photocells (Tx / Rx)
2x0.5mm
2
/ 4x0.5mm
2
30m
D: Pushbutton/wall key
2x0.5mm
2
50m
E: Antenna
Coaxial cable 50
k
(RG-58/U)
5m
MSM-049/02 – 2020
-01-1
3
V1.08 o
r later
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
8 Unlocking D295J 1 Turn the cover (1). 2 Insert the key (2) and turn it clockwise without forcing it (the cylinder willbe pushed out a few millimetres by the spring). 3 Operate the handle (3) by turning it 180º to the left. The gate can now beoperated manually. 4 In order to extract the key and lea...
9 ESC ENTER P274I ESC ENTER P274J ENTER ESC P274Y P274ZZ ESC ENTER Turning direction change and check ( C1 ) ESC ENTER P274H ESC ENTER P274K ENTER ESC P274V ENTER ESC P274W 1 Press ENTER, with the display showing rSXX ( rS º Â 8 , rS º â 8 , rS 8º @ , rS 8º ? , etc). ESC ENTER ESC P274X Interchang...
10 ESC ENTER P274B ESC ENTER P274C ESC ENTER P274D I II P295E ESC ENTER P274F ESC ENTER P274G Total opening radio code programming P1 (with RSD receiver only, C801 ) If a receiver other than RSDis used, see thecorresponding instructions. Select the option C801 (RSD receiver) beforestarting progr...
