Page 2 - CAUTION; WARNING
Table of Contents Safety Precautions .................................................................2 Français ..............................................................................14Español ...............................................................................16 General Descripti...
Page 3 - Grounding Instructions
GAS ENGINE (WHERE APPLICABLE) Always place sprayer outside of structure in fresh air. Keep allsolvents away from engine exhaust. Never fill fuel tank with arunning or hot engine. Hot surface can ignite spilled fuel.Always attach ground wire from pump to a grounded object.Refer to engine owner’s manu...
Page 4 - Setup; Preparing a New Sprayer; Preparing to Paint
General Description This airless sprayer is a precision power tool used for sprayingmany types of materials. Read and follow this instructionmanual carefully for proper operating instructions,maintenance, and safety information. Operation This equipment produces a fluid stream at extremely highpress...
Page 5 - Painting; Electronic Pressure Control Indicators
8. Move the PRIME/SPRAY valve up to the SPRAY position.9. Turn the unit on. 10. Unlock the gun by turning the gun trigger lock to the unlocked position. Ground the gun by holding it againstthe edge of the metal container whileflushing. Failure to do so may lead toa static electric discharge, which m...
Page 6 - Spraying; Spraying Technique; Practice
Spraying POSSIBLE INJECTION HAZARD. Do not spray without thetip guard in place. Never trigger the gun unless the tip isin either the spray or the unclog position. Always engagethe gun trigger lock before removing, replacing, orcleaning tip. Spraying Technique The following techniques, if followed, w...
Page 7 - Cleanup; Maintenance; General Repair and Service Notes
Cleanup Special cleanup instructions for use with flammablesolvents: • Always flush spray gun preferably outside and at least one hose length from spray pump. • If collecting flushed solvents in a one gallon metal container, place it into an empty five gallon container, thenflush solvents. • Area mu...
Page 8 - Replacing the Filters; Pump Filter
Replacing the Filters Pump Filter 1. Loosen and remove the filter housing by hand.2. Slip the filter off of the filter support spring.3. Inspect the filter. Based on inspection, clean or replace the filter. 4. Inspect the o-ring. Based on inspection, clean or replace the o-ring. 5. Slide the new or ...
Page 9 - Replacing the Gears; Replacing the Transducer
Replacing the Gears 1. Unplug the unit.2. Loosen and remove the four motor shroud screws. Remove the motor shroud. 3. Release the baffle tape on the side of the baffle assembly and slip the baffle assembly off of the motor. Remove thefour baffle spacers. 4. Slide the electronic cover off of the elec...
Page 10 - Servicing the Valves
Replacing the PRIME/SPRAY Valve Perform the following procedure using PRIME/SPRAY valvereplacement kit P/N 800-915. 1. Push the groove pin out of the valve handle.2. Remove the valve handle and the cam base.3. Using a wrench, loosen and remove the valve housing assembly. 4. Make sure the gasket is i...
Page 11 - Repacking the Fluid Section
Repacking the Fluid Section 1. Remove the foot valve assembly using the steps in the “Servicing the Valves” procedure above. 2. Using 3/8” a hex wrench, loosenand remove thetwo pump blockmounting screws. 3. Pull the pump block downapproximately 1/2”from the gear boxhousing. 4. Slide the pump block a...
Page 12 - Solution; Cause; Troubleshooting; Problem
Solution 1. Plug the unit in.2. Reset the breaker.3. Turn the pressure control knob clockwise to supply power to the unit and increase thepressure setting. 4. Inspect or take to a Titan authorized service center. 5. Allow motor to cool.6. Replace the ON/OFF switch. 1. Rotate the PRIME/SPRAY valve cl...
Page 13 - Patents
© Titan Tool Inc. All rights reserved. 13 Troubleshooting Problem Excessive surge at the spraygun. Poor spray pattern. The unit lacks power. Cause 1. Wrong type of airless spray hose. 2. The spray tip worn or too large. 3. Excessive pressure. 1. The spray tip is too large for the material being used...
Page 14 - Consignes de sécurité; AVERTISSEMENT; ATTENTION; Français
14 © Titan Tool Inc. Tous droits réservés. Consignes de sécurité Le présent manuel comprend des renseignements devant êtrelus attentivement avant toute utilisation de l'appareil. Lorsquel'un des symboles suivants apparaît, il est recommandé d'êtreparticulièrement attentif et de tenir compte des mesu...
Page 15 - Instructions de mise à la terre
© Titan Tool Inc. Tous droits réservés. 15 MOTEUR À ESSENCE (DANS LES CAS OÙ CELA S’APPLIQUE) Toujours placer la pompe à l’extérieur de la structure à l’airfrais. Garder tous les solvants loin de l’échappement dumoteur. Ne jamais remplir le réservoir à carburant lorsque lemoteur est en marche ou lor...
Page 16 - Español; Precauciones de seguridad; ADVERTENCIA; PRECAUCION
Español 16 © Titan Tool Inc. Todos los derechos reservados. Precauciones de seguridad Este manual contiene información que debe leer y comprenderantes de usar el equipo. Cuando se encuentre con uno de lossiguientes símbolos, asegúrese de observar sus indicacionesde seguridad. Este símbolo indica la ...
Page 17 - Instrucciones para conectar a tierra
© Titan Tool Inc. Todos los derechos reservados. 17 PELIGRO: PELIGRO DE EXPLOSIÓN DEBIDO A MATERIALES INCOMPATIBLES - Podríacausar lesiones severas o daños en lapropiedad. PARA PREVENIR: • No utilice materiales que contengan blanqueador o cloro.• No use solventes con hidrocarburos halogenados, tales...
Page 18 - Parts List; Main Assembly
18 © Titan Tool Inc. All rights reserved. Parts List Main Assembly 1 4 3 2 6 8 9 7 10 5 11 14 13 3 12 Item Part # Description Quantity 1 800-570 High Rider cart assembly ...........................1 2 ---------- Gear box assembly (see separate listing) ..1 3 ---------- Fluid section assembly (see se...
Page 19 - Motor Assembly; Electrical Schematic
© Titan Tool Inc. All rights reserved. 19 11 10 9 12 13 14 7 8 3 4 5 6 1 2 Motor Assembly Item Part # Description Quantity 1 800-465 Motor shroud...............................................2 2 705-063 Electronic cover ..........................................1 3 700-681 Screw ......................
Page 20 - Gear Box Assembly
20 © Titan Tool Inc. All rights reserved. Gear Box Assembly 2 1 3 4 5 6 7 10 11 8 9 12 13 14 18 2 19 20 15 16 17
Page 22 - Fluid Section Assembly
22 © Titan Tool Inc. All rights reserved. Fluid Section Assembly 1 2 30 4 3 5 7 6 8 11 12 14 15 16 17 18 19 20 21 22 23 13 10 9 24 25 26 27 29 28 42 43 31 32 33 34 35 36 38 37 39 40 41 Install upper packing with raised lip and o-ring facing down. O-Ring Raised Lip NOTE: When using “HOT” solvents, re...
Page 24 - Warranty; United States Sales & Service; International; Accessories; Airless Tip Selection; Piston Lube; Miscellaneous; Labels
24 © Titan Tool Inc. All rights reserved. Warranty United States Sales & Service 1-800-526-5362 Fax 1-800-528-4826 107 Bauer Drive Oakland, NJ 07436 www.titantool.com Canadian Branch 1-800-565-8665 Fax 1-905-856-8496 200 Trowers Road, Unit 7B Woodbridge, Ontario L4L 5Z8 International 1-201-337-1...
