Timex T020 - Manual

Model T020

Para instruccionese en Espanol, llame al 1-800-888-4491.

For questions or comments regarding this or other

products, please call our toll-free number 1-800-888-4491.

For additional information, online registration,

and exclusive special offers visit our website:

Thank you for purchasing this Timex model T020 Alarm Clock. Please read this

instruction manual carefully and completely to insure that you understand the

proper operation of your new alarm clock, and that you get the maximum benefit

from all the advanced features included in this model.

www.timexaudio.com

Limited 90-Day Warranty Information

Timex Audio Products, a division of SDI Technologies Inc. (hereafter referred to as SDI Technologies),

warrants this product to be free from defects in workmanship and materials, under normal use

and conditions, for a period of 90 days from the date of original purchase.
Should service be required by reason of any defect or malfunction during the warranty period,

SDI Technologies will repair or, at its discretion, replace this product without charge (except for a

$3.00 charge for handling, packing, return UPS/postage, and insurance). This decision is subject

to verification of the defect or malfunction upon delivery of this product to the Factory Service

Center listed below. The product must include proof of purchase, including date of purchase. The

fee for service after the warranty period or without proof of purchase is $6.00.
Before returning this product for service, please first replace the batteries (if applicable) with fresh

ones, as exhausted or defective batteries are the most common cause of problems encountered.
If service is still required:
1. Remove batteries (if applicable) and pack the unit in a well-padded, heavy corrugated box.
2. Enclose a photocopy of your sales receipt, credit card statement, or other proof of the date

of purchase.

3. Enclose a check or money order payable to the order of Soundesign, for the sum of $3.00 (or

$6.00 if after the warranty period or without proof of purchase).

4. Send the unit prepaid to the Factory Service Center listed below:

Consumer Repair Department

SDI Technologies Inc.

Timex Audio Products Division

1330 Goodyear Dr.

El Paso, TX 79936-6420

NOTE:

This warranty is valid only if the product is used for the purpose for which it was designed.

It does not cover (i) products which have been damaged by negligence, misuse or accident, or

which have been modified or repaired by unauthorized persons; (ii) cracked or broken cabinets,

or units damaged by excessive heat; (iii) damage to tape cassettes (if applicable); (iv) the cost of

shipping this product to the Factory Service Center and its return to the owner.
This warranty is valid only in the United States of America and does not extend to owners of the

product subsequent to the original purchaser. Any applicable implied warranties are also limited

to 90 days, and SDI Technologies will not be liable for consequential damages. (Some states do

not allow limitations on implied warranties or exclusion of consequential damages, so these

restrictions may not apply to you.) This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

TIMEX is a registered trademark of Timex Corporation the United States and other countries.

T020-042209-A

Printed in China

Alarm Clock with

Month / Date / Day

Display

MODEL: T-020 (FRONT)
INSTRUCTION MANUAL
SCALE: 360W x 174H mm
DATE: April 22, 2009
COLOR: WHITE BACKGROUND PRINTING BLACK

MODEL: T-020 (Rear)
INSTRUCTION MANUAL
SCALE: 360W x 174H mm
DATE: April 22, 2009
COLOR: WHITE BACKGROUND PRINTING BLACK

Setting the Clock

Selecting 12-Hour or 24-Hour Display Mode

Press the



button momentarily to switch the display between the 12-Hour and 24-Hour

format. If you select the 24-Hour format the “24H” indicator will appear in the display. In

the 24-Hour format midnight is displayed as “0:00”, 1 PM is displayed as “13:00”, 6 PM

is displayed as “18:00”, etc. The 24-Hour format is often referred to as Military Time.
In the 12-Hour format midnight is displayed as “12:00”. Noon is displayed as
“PM 12:00”. If the “

PM

” indicator does not appear, the time displayed is AM. There is no

AM indicator.

Setting The Time / Year / Month and Date

After you have selected the 12 or 24-Hour display format, proceed as follows:
1. Press and hold the

MODE

button for two seconds until the Hour digits begin flashing,

then press either the



or



buttons to set the display to the correct hour,

AM

or

PM

. If the

PM

indicator does not appear the hour displayed is

AM

.

2. When the correct hour appears press the

MODE

button once to start the Minute

digits flashing, then press either the



or



buttons to set the display to the

correct minute.

3. When the correct minutes appear press the

MODE

button once to start the Seconds

digits flashing. If you want to set the seconds counter to “00” press either the



or



button once. If you do not wish to ‘zero’ the seconds, proceed to step 4.

4. Press the

MODE

button once more to start the Year display flashing. The default

year is 2004. Press the



button to set the display to the correct year.

5. Press the

MODE

button once more to start the Month display flashing, then press

either the



or



buttons to set the display to the correct month.

6. Press the

MODE

button once more to start the Date display flashing, then press

either the



or



buttons to set the display to the correct date. Note that the

Day of the Week indicator changes automatically as you adjust the Date display.

7. After you have completed these adjustments you may press the

MODE

button once

more to exit the setting mode and return to the current time display. Or if you do

nothing the display will return to the current time automatically after 15 seconds.

Note:

You must complete each of the above steps and move to the next step within 15

seconds. If you do not make any adjustment within 15 seconds the clock will exit the

setting mode and return to the previously displayed information. You must then start with

Step 1 again and make sure you complete each step within 15 seconds, while the display

is flashing.

Operating Instructions

Controls

Controls and Their Functions

Preparation for Use

Mode/Set Button

Snooze/Light Button

Snooze/Alarm
On/Off Button

Installing the Batteries

Open the Battery Compartment cover by

pressing down on the locking tab. Insert 2 “AA”

batteries (not included) in the battery

compartment. Be sure to insert the batteries

according to the polarity markings ( “+” / “−“)

inside the battery compartment. If the batteries

are inserted incorrectly the unit will not work.

We recommend you use a well-known brand of

alkaline batteries for longest life and best

performance.

Snooze Bar

– When Snooze function is activated, press to stop alarm temporarily.

After 5 minutes alarm turns ‘On’ again. Snooze operation can be repeated up to 8

times. If snooze is not activated, pressing Snooze Bar resets alarm to following day.

During normal operation, pressing the Snooze Bar also turns on the display

backlighting momentarily for nighttime viewing. After 5 seconds the lighting turns off

automatically.

MODE Button

– Used to switch between time and alarm time display modes, and

to enter manual time and alarm setting modes.



/12/24 Button

- Used to switch the time display between 12-hour and 24-hour

formats. Also used to manually advance the time, year, month, and date displays.



Button

– Used to manually ‘back-up’ the time, year, month, and date displays.

Snooze/Alarm On/Off Button

– Use to activate or deactivate the alarm and

activate or deactivate the Snooze function.

Setting the Alarm Time

1. When the correct time, month, and date are showing on the display press the

MODE

button once to change the display from current time to alarm time. The initial default

alarm setting is 12:00 (AM). The “

AL

” indicator appears between the Hour and

Minute digits to confirm that you are in the alarm-setting mode.

2. While the display is in the alarm-setting mode press and hold the

MODE

button for

two seconds until the Alarm Hour digits begin flashing, then press either the



or



buttons to set the display to the desired wake-up hour,

AM

or

PM

. If the

PM

indicator does not appear the hour displayed is

AM

.

3. When the desired wake up hour appears press the

MODE

button once to start the

Minute digits flashing, then press either the



or



buttons to set the display

to the desired wake-up minute.

4. When the desired wake-up time appears on the display you may press the

MODE

button once more to return to the current time display. After 15 seconds the display

returns to the current time mode automatically.

5. If you wish to reconfirm the wake-up time just press the

MODE

button once. The

display will change from current time to alarm time. After 15 seconds the display

changes back to current time automatically.

Activating The Alarm and Snooze Functions

To turn the alarm ‘On’ press the

Snooze/Alarm

On/Off

button on the front panel once.

The Alarm On indicator appears in the display.
To activate the Snooze function press the

Snooze/Alarm

On/Off

button once more.

The Snooze indicator appears in the center of the display.
At the selected wake-up time the alarm turns on automatically. The alarm begins with a

single ‘beep’ and then the frequency of the ‘beeps’ increases. The alarm continues for

two minutes, then shuts off automatically and resets itself for the same time on the

following day.
To stop the alarm sooner, press any button on the front panel. The alarm stops immediately

and resets itself for the same time on the following day.

Snooze Function

If you activated the Snooze function and the Snooze indicator appears in the display after

the alarm turns on you may press the Snooze Bar for an extra 5 minutes sleep. The alarm

will stop and then start again 5 minutes later. You may repeat the Snooze operation up

to 8 times, but after 8 times the alarm resets itself for the following day. The Snooze

indicator flashes in the display during Snooze operation.

Deactivating The Alarm and Snooze Functions

To deactivate the Alarm and Snooze functions, press the

Snooze/Alarm On/Off

button

until both the Alarm indicator and Snooze indicator disappear from the display.

If you notice that the time display is beginning to fade, or if it has completely disappeared,
replace the batteries. Replace both batteries at the same time and do not mix different
types of batteries. Do not leave exhausted batteries in the clock for a long period of time.
They may eventually leak and cause damage to the clock itself or to the surface the clock
is placed on.
Please dispose of the exhausted batteries properly.

Note:

After replacing the batteries the clock will return to its original default settings. It

will be necessary to reset the time and alarm settings.

Care and Maintenance

Time Display

Day
Indicator

Month /
Date
Indicator

Time

Display

Snooze Indicator

Alarm Indicator

Seconds Indicator

Alarm Time Indicator

PM Indicator

24 Hour

Indicator

UP /



12/24 Button

Down



Button