Tiger M105X/S - Manual

Table of Contents:

• Page 3 – FORWARD; Tiger Corporation
• Page 4 – TABLE OF CONTENTS; This symbol means; CAUTION – YOUR SAFETY IS AT RISK!; When you see this symbol, read and
• Page 6 – SAFETY; General Safety Instructions and Practices; The symbol and signal word are intended to warn the owner /; Practice all usual and customary safe working precautions and; YOU; can
• Page 15 – SEE YOUR DEALER
• Page 19 – MOWER DECK
• Page 20 – FRONT PUMP MOUNT
• Page 24 – CAB FENDER
• Page 27 – FEDERAL LAWS AND REGULATIONS
• Page 30 – ASSEMBLY; B e f o r e a t t e m p t i n g t o m o u n t y o u r T i g e r m o w e r, i t i s; TRACTOR PREPARATION; B: Disconnect battery cables from both batteries.; ADJUSTING REAR WHEELS
• Page 31 – NOTE; MAIN FRAME INSTALLATION; NOTE: THE FUEL TANK IS REPLACED ONLY ON BOOM UNITS.
• Page 32 – brackets to the tank with the hardware shown in the parts section.; FRONT PUMP MOUNTING; C A U T I O N : D O N O T S TA R T T H E T R A C TO R U N T I L A L L H O S E S A R E; TEMPERATURE GAUGE MOUNTING
• Page 34 – Use the image below for positioning the cable control; VALVE MOUNTING BRACKET
• Page 35 – CABLE SWITCH BOX WIRING; Using a test light or meter verify; this wire is the neutral safety wire.; NOTE: Be certain that the power taken
• Page 36 – HIGH PRESSURE FILTER - HUSCO
• Page 38 – steel bands provided must be used.; HOSE COVERING
• Page 40 – and lock into place with locking bolt on clevis.
• Page 41 – the combo draft beam.
• Page 42 – cylinder butt. Use teflon tape on all fitting and hose connections.
• Page 43 – other edges that may rub hoses.
• Page 44 – Before operating the mower; , the cutter head and draft beam should be slowly; MOWER TESTING; If any parts of this assembly section, or any other section of this
• Page 46 – OPERATION; Safety; The; Safety Alert Symbol; combined with a signal word, as seen below, is; Before any operation of tractor and mower; , the user should read and
• Page 47 – feet; of the machine when mower is in operation.; OPEN; before; OFF”; position. The unit is; CONTROL LOCATION AND FUNCTIONS
• Page 48 – of the machine when in operation. Extreme care should be taken
• Page 49 – The engine; use excessive force when positioning cutting head into heavy
• Page 50 – Transporting under the units own power:
• Page 51 – OPEN THE BALL VALVES ON THE; Serious damage
• Page 53 – DO NOT OPERATE an UNSAFE TRACTOR or MOWER
• Page 55 – DO NOT OPERATE an UNSAFE TRACTOR or FRONT END
• Page 58 – MAINTENANCE; Wheel lugs must always be re-torqued whenever a wheel is; BREAK IN PERIOD; water, using a soft clean sponge or; soft cloth; . DO NOT use abrasive or alkaline; use hands to check for suspected leaks in hydraulic hoses!
• Page 59 – DAILY OR EVERY 8 HOURS
• Page 60 – Rear Tire Type; YEARLY OR EVERY 500 HOURS; Vibration
• Page 61 – SYMPTOMS
• Page 62 – Motor will not work; on internal parts
• Page 65 – SUPERCOATED; SUPERCOATTM HARD-COAT
• Page 66 – RECOMMENDED FILLING INSTRUCTIONS; OFF; ”, and allowed sufficient time to cool to ambient temperature.; DETAILED MAINTENANCE
• Page 67 – REPLACEING HIGH PRESSURE HYDRAULIC FILTER ELEMENT:
• Page 71 – maintenance or repair procedures.; THE BALL VALVES MUST BE OPEN (handle; Failure to do so may result in component failure!; ADJUSTING THE CABLE LIFT
• Page 74 – in; weld on the knife or bolts. Damaged or worn knives must be replaced.; NOT; self-locking nut is removed from the knife mounting bolt, the nut; must; be replaced
• Page 76 – A press MUST be used to install bearing cups, bearing cones, and; when working on spindle assembly.; THE SPINDLE ASSEMBLY
• Page 77 – – Press upper bearing cup into the spindle housing.
• Page 79 – The following services should be performed; daily; or every; hours; lubricate at zerks.; Maintenance Section
• Page 81 – SIDE ROTARY
• Page 82 – Tiger; Direct any questions regarding parts to:; PARTS ORDERING GUIDE
• Page 83 – PARTS SECTION TABLE OF CONTENTS; SECTION
• Page 84 – TRACTOR MOUNT KIT - MAIN FRAME M105X
• Page 86 – TRACTOR MOUNT KIT - HYDRAULICS M105X
• Page 88 – COMBO DRAFT BEAM
• Page 90 – SPOOL HUSCO CONTROLS - KUBOTA M105X
• Page 92 – SP HUSCO LIFT VALVE - COMBO
• Page 94 – SP HUSCO LIFT VALVE - CABLE
• Page 100 – SAFETY SCREEN - KUBOTA M105X
• Page 102 – OPTIONAL PUMP GUARD KIT
• Page 103 – OPTIONAL PUMP AND GRILL GUARD KIT
• Page 104 – FUEL TANK - KUBOTA M105X
• Page 105 – SWITCH BOX SCHEMATIC
• Page 106 – SOLENOID BRAKE VAVLE ASSEMBLY
• Page 109 – SIDE ROTARYCOMMON SECTION; COMMON
• Page 112 – CABLE LIFT ASSEMBLY
• Page 116 – 0” SIDE CABLE ROTARY MOWER
• Page 118 – 2” SIDE CABLE ROTARY MOWER
• Page 120 – 0” SIDE COMBO ROTARY MOWER
• Page 122 – 0” SIDE ROTARY MOWER
• Page 124 – 0” SIDE ROTARY SPINDLE AND SPACER
• Page 126 – 2” SIDE COMBO ROTARY MOWER
• Page 128 – TM72” MOTOR ASSEMBLY
• Page 129 – PAGE
• Page 130 – CHAIN GUARDS
• Page 131 – SIDE ROTARY CHAIN GUARDS
• Page 132 – SIDE ROTARY CASTER WHEEL ASSEMBLY
• Page 134 – RESERVOIR TANK FILTER ASSEMBLY
• Page 140 – HYDRAULIC LIFT CYLINDER
• Page 142 – ROTARY KNIVES AND DISKS
• Page 143 – CASTER WHEEL ASSEMBLY
• Page 144 – ROTARY MOTOR
• Page 146 – HYDRO PUMP & TSR MOTOR
• Page 148 – SIDE COOLER
• Page 162 – SOLENOID VALVE ASSEMBLY
• Page 163 – SOLENOID BRAKE VALVE ASSEMBLY
• Page 164 – BRAKE VALVE ASSEMBLY W/ METRI PAK
• Page 165 – SOLENOID BRAKE VALVE HYDRAULIC SCHEMATIC
• Page 166 – TRAVEL LOCK LIFT BEAM
• Page 168 – SWITCHBOX SERVICE PARTS
• Page 169 – SWITCHBOX SCHEMATIC
• Page 173 – WARRANTY INFORMATION; THERE ARE NO WARRANTIES WHICH EXTEND; AFTER
• Page 174 – reserve the right to change specifications or design at any time.
• Page 175 – OPERATOR REQUIREMENTS: