Page 2 - Complete this page for quick reference when service is required:; Date of Installation:; Information found on the data label:; Voltage
Complete this page for quick reference when service is required: Taylor Distributor: Address: Phone: Service: Parts: Date of Installation: Information found on the data label: Model Number: Serial Number: Electrical Specs: Voltage Cycle Phase Maximum Fuse Size: A Minimum Wire Ampacity: A E June, 200...
Page 3 - Table of Contents
Table of Contents Model 390 Table of Contents Section 1 To the Installer Page 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Water Connections Page 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Air Cooled Units Page 1...
Page 5 - Section 1; Water Connections; Air Cooled Units
1 Model 390 To the Installer 040419 Section 1 To the Installer This machine is designed for indoor use only. DO NOT install the machine in an area where a water jet could be used. Failure to follow thisinstruction may result in serious electrical shock. Water Connections (Water Cooled Units Only) An...
Page 6 - Section 2; Compressor Warranty Disclaimer
2 Models 383 & 384 To the Operator 050906 Section 2 To the Operator The slush freezer you have purchased has beencarefully engineered and manufactured to give youdependable operation. The Taylor equipment, whenproperly operated and cared for, will produce aconsistent quality product. Like all me...
Page 7 - Section 3
3 Model 390 Safety 040419 Section 3 Safety We at Taylor Company are concerned about the safetyof the operator when he or she comes in contact withthe freezer and its parts. Taylor has gone to extremeefforts to design and manufacture built-in safetyfeatures to protect both you and the service technic...
Page 8 - Section 4
4 Model 390 Operator Parts Identification Section 4 Operator Parts Identification Item Description Part Number 1 Hopper Cover X38458 2 Gasket-- Hopper Cover 038375 3 Feed Tube 015176-9 4 Drip Pan 035034 5 Splash Shield 046177 6 Drip Tray 046275
Page 9 - Beater Assembly
5 Model 390 Operator Parts Identification Beater Assembly Item Description Part Number 1 Freezer Door X47982 2 Gasket-Door 014030 3 Front Bearing 013116 4 O-Ring-- Baffle 018550 5 Baffle Arm 047729 6 Baffle X47731 7 Guide Bearing 014496 8 Beater X46233 9 Scraper Blade 046237 10 Clip-Scraper Blade 04...
Page 10 - Section 5; Control Switch
6 Model 390 Important: To the Operator Section 5 Important: To the Operator Control Switch The center position is “OFF”. The “WASH” positionactivates the beater motor only. The “AUTO” positionallows the beater motor and compressor to run. Indicator Light -- “Mix Low” Located on the front of the mach...
Page 11 - Section 6; Assembly
7 Model 390 Operating Procedures Section 6 Operating Procedures Following are step-by-step operating procedures forthe model 390 slush freezer. This unit has a 20 quart(18.9 liter) mix hopper and the freezing cylinder holds7 quarts (6.6 liters) of slush product. We begin our instructions at the poin...
Page 12 - Sanitizing; Priming
8 Model 390 Operating Procedures Step 5Install the freezer door. Place the front end of the baffleinto the hole in the center of the door. Position the dooronto the four studs on the front of the freezing cylinderand push the door into place. Install the fourhandscrews onto the studs and tighten the...
Page 13 - Closing Procedures; Rinsing
9 Model 390 Operating Procedures Closing Procedures To disassemble the model 390, the following items willbe needed: S Two cleaning pails S Sanitized stainless steel rerun can with lid S Necessary brushes (provided with freezer) S Cleaner S Single service towels Draining Product From TheFreezing Cyl...
Page 14 - Cleaning
10 Model 390 Operating Procedures Cleaning Step 1Prepare two gallons (7.6 liters) of an approvedcleaning solution (example: Kay-5 r ). USE WARM WATER AND FOLLOW THE MANUFACTURER’SSPECIFICATIONS. Step 2Pour the two gallons (7.6 liters) of cleaning solutioninto the hopper and allow it to flow into the...
Page 15 - Brush Cleaning
11 Model 390 Operating Procedures Brush Cleaning Step 1Prepare a sink with an approved cleaning solution(example: Kay-5 r ). USE WARM WATER AND FOL- LOW THE MANUFACTURER’S SPECIFICATIONS.(If another approved cleaner is used, dilute accordingto label instructions.) IMPORTANT: Follow label directions,...
Page 16 - Section 7; During Cleaning And Sanitizing; Troubleshooting Guide
12 Model 390 Operating Procedures Section 7 Important: Operator Checklist During Cleaning And Sanitizing Cleaning and sanitizing schedules are governed byyour State or local regulatory agencies and must befollowed accordingly. The following check pointsshould be stressed during the cleaning and sani...
Page 17 - Winter Storage
13 Model 390 Operating Procedures Winter Storage If the place of business is to be closed during the wintermonths, it is important to protect the freezer byfollowing certain precautions, particularly if thebuilding is to be left unheated and subject to freezingconditions. Disconnect the freezer from...
Page 18 - Section 8
14 Model 390 Operating Procedures Section 8 Troubleshooting Guide PROBLEM PROBABLE CAUSE REMEDY PAGE REF. 1. No product being dispensed with draw valveopened. a. Improper mixing of product. a. Carefully follow directions for mixing product. -- -- b. Mix low condition. b. Add mix to mix hopper. 6 2. ...
Page 21 - lan
Section 10 Parts List 17 + Available Separately Model 390 Parts List C o p e lan d C o m p re sso r - J8086700/U p (U p d a te 134) DE S CRI P T IO N P ART NUMBE R QT Y. WARR. CLAS S RE MARKS P ART S UP DA T E ARM -BAFFLE *390* 047729 1 103 J4040000/ UP 83 BAFFLE ASSEMBLY X47731 1 103 J4040000/ UP 8...
Page 28 - Wiring Diagrams
