Page 2 - Table of Contents; CONNECTING TO THE DATAPORT COMMAND INTERFACE THROUGH THE RS-
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 2 Table of Contents 1. INTRODUCTION .......................................................................................................................... 3 2. CONNECTING TO THE DATAPORT COMMAND INTERFACE THROUGH THE RS- 232 PORT. ....
Page 3 - The
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 3 1. Introduction The TANDBERG GW Dataport Command Interface User Guide contains guidelines on how to use the textual command interface supported by the GW. The Dataport Command Interface can be accessed through Telnet via the LAN inter...
Page 4 - Hardware And Cabling; TANDBERG GW
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 4 2. Connecting to the Dataport Command Interface through the RS-232 port. The RS-232 port is a 9-pin, female, D-sub connector located on the back of the GW. The port is configured as a DCE (Data Communications Equipment). The RS-232 po...
Page 5 - Configuring The Dataport From The Web Interface; Click on; Troubleshooting
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 5 2.2. Configuring The Dataport From The Web Interface Click on System Configuration tab and then the Dataport button. The Dataport can be configured by setting baudrate, parity, databits and stopbits. 2.3. Troubleshooting If communicat...
Page 6 - Connecting to the Datport Command Interface using Telnet
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 6 3. Connecting to the Datport Command Interface using Telnet The TANDBERG GW has two LAN ports. Connection to the Dataport Command Interface via Telnet should be done through LAN port 1. The GW’s Telnet server provides access to the Da...
Page 7 - The TANDBERG GW Commands; parameters
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 7 4. The TANDBERG GW Commands 4.1. Introduction Typing ‘ ? ’ or ‘ help ’ when connected to the Dataport Command Interface will return a list of valid commands. The commands are used to control the functions of the GW. A command may be f...
Page 8 - *R Invalid gateway id; ippassword; *P parameter feedback; pardial on; pardial; OK; feedback; commands
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 8 case where the user is trying to transfer a call from an inactive GW port (the user input is shown in bold). calltransfer 1 999999 *R Invalid gateway id ERROR Parameter Setting Commands are commands that set a system parameter to a sp...
Page 9 - all; NOTE! The GW needs to reboot before the changes will apply
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 9 4.2.1. System Configuration Commands Command: Description: defvalues set This command is used to restore factory default settings. Issuing this command with no parameters will restore all settings except network settings and option ke...
Page 10 - *P ipassignment 1 static
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 10 Example of ipaddress feedback: *P ipaddress 1 static 10.0.5.98 *P ipaddress 1 subnetmask 255.255.0.0 *P ipaddress 1 gateway 10.0.0.1 ipassignment Selects between DHCP (Dynamic Host Configuration Protocol) or static IP address allocat...
Page 11 - NOTE! The network has to be RSVP enabled to use this protocol
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 11 best available setting. Example of ipspeed feedback: *P ipspeed 1 auto ipqos Configures the different Quality of Service (QoS) algorithms supported by the TANDBERG GW. QoS are used to set priority on QoS enabled IP networks. ipqos pr...
Page 15 - *P services telnet on
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 15 o euro - Euro ISDN Example of prinet feedback: *P prinet att prinumbrange Defines the PRI number range for the various PRI interfaces. prinumbrange <PRI interface> <lowest number> <highest number> --- parameters: • ...
Page 17 - Example of; sport; Textstring of maximum 16 characters.; systemname; *P systemname TANDBERG
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 17 Example of sport feedback: *P sport 9600 n 8 1 systemname Sets the GW name. systemname <name> --- Parameters: • name: Textstring of maximum 16 characters. Example of systemname feedback: *P systemname TANDBERG
Page 18 - GW; calltransfer; directory all; NOTE! The user should be aware not to overwrite existing entries.; netprofile; directory; disc
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 18 4.2.2. General GW Commands Command: Description: calltransfer Disconnects the h323 terminal of a GW call and reconnects to another h323 terminal, by either specifying a telephone number or by referring to a directory entry. calltrans...
Page 19 - gwdid
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 19 disc <gwid> --- parameters: • gwid: 1..16. Identifier referring to a GW call. gwdid Sets ISDN DID (Direct Inwards Dialling) parameters. When DID is enabled the GW will strip of the last digits in the ISDN incoming number and us...
Page 20 - gwhotline
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 20 gwh323service <id> servprefix <e164prefix> or gwh323service <id> maxbw <bw> or gwh323service <id> isdncallprefix <callprefix> or gwh323service <id> restrict <on/off> or gwh323service &l...
Page 21 - or; natvid; : Sets natural video support to on or off.; customformats; : Sets custom format support to on or off; duovideo; : Sets duovideo support to on or off; encryption
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 21 or gwsettings duovideo <on/off> or gwsettings encryption <on/off> sub-commands: • natvid : Sets natural video support to on or off. • customformats : Sets custom format support to on or off • duovideo : Sets duovideo supp...
Page 22 - chan; *S callstatus 1 outgoing bonding connected 255 2446Sec
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 22 4.2.3. System Status Commands Command: Description: callhistory Used to list call related information for the last 20 calls. callhistory [logid] Status format: callhistory <logid> <logtag> <gwlogtag> <remote numb...
Page 23 - chanstat
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 23 chanstat Used to list channel status information for the PRI interface. chanstat [pri interface] [channel] Status format: chanstat <PRI interface> <channel> <channel-status> <calling-number> <causeLoc>:&...
Page 24 - gwcalls
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 24 • h323 callid: The call id of the h323 terminal • h323 termnumber: The number of the h323 terminal Example of gwcalls feedback: *S gwcalls 1 1 22222222 2 66666666 h323gkstatus Returns current gatekeeper status. h323gkstatus Status fo...
Page 26 - pristatus
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 26 • PRI interface: a/b/c/d. Letters identifying the different PRI interfaces. o a : PRI interface 1 o b : PRI interface 2 o c : PRI interface 3 o d : PRI interface 4 • status: disabled / red alarm / blue alarm/ yellow alarm / synced / ...
Page 27 - statout
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 27 • vidres: unknown / cif / qcif / sqcif / 4cif / sif / 4sif / vga / svga / xga • duores: cif / qcif / sqcif / 4cif / sif / 4sif / vga / svga / xga Example of statout feedback: *S statout 1 outgoing synced norestrict h323-768 g722 h263...
Page 28 - Commands; isdntrace
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 28 4.2.4. Debug Commands Command: Desription: eventlog The eventlog records all serious errors registered by the system. The log can be used to identify the cause for errors. The complete eventlog can be downloaded from the embedded FTP...
Page 31 - Storage; Parameter Setting Commands,; Command
TANDBERG GW Dataport Command Interface User Guide D13202 Rev 01 31 4.3. Parameter Storage Parameters are set by issuing Parameter Setting Commands, ref. chapter 4.1.2 . All parameters and their corresponding storage type are listed in the table below. The following definitions are used: level 0: No ...
