South Bend SB1044 - Manual
South Bend SB1044 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – I N S T R U C T I O N S; Installation; For Power Connection; Figure 2. Cutting fluid system installation.; To install the cutting fluid kit:
- Page 3 – Operation; To use the cutting fluid system:; Coolant Switch
- Page 4 – Maintenance; Qty; To change the cutting fluid:; Leaving the pump running with an empty
- Page 5 – Troubleshooting; Symptom
- Page 6 – Electrical Safety Instructions; Circuit Requirements:; WIRING DIAGRAM COLOR KEY
- Page 7 – Model SB1029 Pump Connection Wiring Diagram
- Page 8 – Parts List; of the problem you are having.; Warranty
Instruction Sheet
PHONE: (360) 734-1540 •
www.southbendlathe.com
MODEL SB1044
CUTTING FLUID KIT
Specifications
•
Motor .......................................................
1
⁄
8
HP
•
Phase & Cycle ................. 3-Phase & 50/60 Hz
•
Voltage ............................................220V/440V
•
Current ..................................... 0.3/0.15 Amps
•
Pump Type ..................................................Jet
• Pump Flow ........................................ 8.2 GPM
• Cutting Fluid Type ......... Water-Soluble Only
•
Maximum Tank Capacity ...................... 9 Gal.
•
Net Weight ............................................. 73 lbs
•
Country of Origin ................................ Taiwan
BIOLOGICAL & POISON
HAZARD!
Use the correct personal
protection equipment
when handling cutting
fluid. Follow federal, state,
and fluid manufacturer
requirements for proper
disposal.
Introduction
This cutting fluid kit is for the Model SB1029
Surface Grinding Machine. The system is
designed to pump water-soluble cutting fluid to
minimize grinding wheel wear, load-up, glazing,
and heat. Using cutting fluid helps maximize
the quality of workpiece results, especially on
materials that should not be ground dry.
Figure 1. Model SB1044.
Unpacking
This item was carefully packaged to prevent
damage during transport. If you discover any
damage, please immediately call Customer
Service at (360) 734-1540 for advice. You may
need to file a freight claim, so save the containers
and all packing materials for possible inspection
by the carrier or its agent.
Inventory
Item:
Qty
•
Tank Assembly w/Pump ................................ 1
—Drain Hose 1
3
⁄
4
" x 5' .................................... 1
—Hose Clamp 1
3
⁄
4
" ........................................ 1
—Delivery Hose
1
⁄
2
'' x 9' ................................. 1
—Hose Clamp 1
3
⁄
4
'' ......................................... 1
—Flex Conduit Power Cord 9' ....................... 1
—Drain Adapter ............................................. 1
—Swivel Caster Wheels ................................. 4
• Splash Guard ................................................. 1
—Button Head Cap Screw M6-1 x 10 ........... 4
—Front & Rear Splash Panel .................. 1 Ea
• Coolant Trough .............................................. 1
Copyright © December, 2010 by South Bend Lathe Co.
WARNING: No portion of this manual may be reproduced without written approval.
#CR13482 Printed in Taiwan
If you need help with your new model
SB1044 Cutting Fluid Kit, contact us at:
PHONE: (360) 734-1540
FAX: (360) 676-1075
EMAIL: [email protected]
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2- Mfg. Since 6/10 Model SB1044 I N S T R U C T I O N S Installation During the installation process of your cutting fluid kit, you'll need the following items: For Power Connection • A power source that meets the minimum circuit requirements for this machine. • A qualified electrician to ensure a ...
Mfg. Since 6/10 Model SB1044 -3- I N S T R U C T I O N S Operation Only use high quality water-soluble cutting fluid in this system. Never attempt to pump straight cutting oils or kerosene. If you do, the higher viscosity of the oil will overload the motor, causing damage, or flammable liquids may i...
-4- Mfg. Since 6/10 Model SB1044 I N S T R U C T I O N S Maintenance When you replace the old cutting fluid, take the time to thoroughly clean out both sides of the tank. Make sure to dispose all old fluid according to local regulations. Cutting fluid is considered hazardous waste by the EPA. Follow...
