Page 2 - English; Contents
English 2 2 Contents 1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..Page 3 1.1 Operating manual notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Page 3 1.2 Description of the appliance ...
Page 3 - Operating manual notes; Technical data
English 3 3 Thank you for choosing this Soehnle Professional product. All the features of this product weredesigned to the state of the art and are optimised for simple and straightforward use. If you have any queries or experience any problems with the appliance that are not addressed inthe operati...
Page 4 - Putting into operation
English 4 4 Scale 1 + 2 Ground (GND) Pressure compensation membrane on IP 65 housing Connections e.g. Profibus, Ethernet, etc. Interface 2 Interface 1 Power supply 1.3 Putting into operation Before connecting the power plug to the mains, make sure that the power supply specified on thenameplate and ...
Page 5 - Max; Symbols; XXXX
English 5 5 Weighing ranges Max Maximum load of weighing range Min Minimum load of weighing range e= Calibration value (resolution) SNR Serial number of scale (scale type, last digits of year of manufacture, consecutive number) EU conformity mark with year of affixing also start of validity of verif...
Page 6 - Control keys; Operating mode
English 6 6 1.7 Control keys Operating mode Setpoint input Setting mode On / Off Zeroing key or Cleartare Set input to zero One menu level back,or shift an editable decadefrom right to left Tare key Increment value Next setting step orincrement value Print key orEnter key Next setting step orincreme...
Page 7 - Electronic nameplate; Display
English 7 7 1.8 Electronic nameplate Press the Info key twice to display the electronic nameplate. Press thearrow keys ( / ) to indicate the electronic nameplate, the Serial No. and the calibration counter of the activated measuring points in the display. Press the CL key to cancel or end display of...
Page 8 - Basic functions; Only when the scale is not loaded.; Switching off; Switch over by pressing the Info key and then the Zeroing key.
English 8 8 2. Basic functions The basic functions are similar or identical for all application programs. 2.1 Power-on Only when the scale is not loaded. After the test routine, the display is set to zero. The scale is ready for use. Place the weighing product on the scale. The display shows the gro...
Page 9 - Taring function
English 9 9 2.5 Taring function Manual tare Place an empty container on the platform and press the -key. Manual tare input In Setting mode (see separate description 470.702.078 User Mode), select"Manual tare input" to assign the key. Then in operation, press the -key to set the value using t...
Page 10 - Ten times resolution X10; UCAL I
English 1 10 0 2.6 Ten times resolution X10 The ten times resolution appears by pressing the -key and the Zeroing key simultaneously. On approved scales, the high resolution appears for 5 seconds or flashes as long as you hold down the keys - on non-approved scales, the high resolution appears as lo...
Page 11 - Hold mode
English 1 11 1 The selected data record is displayed in scroll mode as follows: Scroll by pressing the arrow keys ( / ) up or down. Quite the View mode by pressing the -key. Press the -key and then hold down the - and - keys for 5 seconds to switch back to Weighing mode. 2.9 Hold function The hold f...
Page 12 - Inputs and outputs
English 1 12 2 2.10 Inputs and outputs The optional I/O module has 4 inputs and outputs that can be individually configured in Setting mode (see (separate description 470.702.078 User Mode). 2.11 LED lamps The appliance has integrated LED lamps. The functionality can be set and activated individuall...
Page 13 - Weighing; The counting function is activated by pressing the Counting key.; Counting with tare
3.0 Application programs The various application programs on the Soehnle Basic Terminal 3010 offer you a wide range of solutions for weighing operations. You can modify the application programs to your specific requirements in Setting mode (see separate description 470.702.078 User Mode). Below is a...
Page 14 - Displaying the piece weight; A full total memory is recognised by the totalising character (; Call up the total value; by pressing the CL key and then the + key.; Totalising with tare
English 1 14 4 Displaying the piece weight Press the Info key and then the counting key to display the piece weight. Press the CL key to go back. 3.3 Totalising Place weighing product on the platform in Weighing mode and accept theweight value in the total memory by pressing the + key. Remove the we...
Page 15 - A full batch memory is recognised by the totalising character (; Batching with tare; Withdrawal weighing
English 1 15 5 3.4 Batching Place weighing product on the platform in Weighing mode and accept the weight value in the batch memory by pressing the + key.Place the next weighing product on the platform and press the + key to accept the weight value in the batch memory, etc. A full batch memory is re...
Page 16 - Switching point programming; Setting the switching points
English 1 16 6 3.6 Switching point programming Four switching points can be set in the Basic Terminal 3010. The switching points are used for switching and dosing. Setting the switching points Press the switching point key. The first switching point is displayed. This is indicated by the arrow in th...
Page 17 - The greatest possible switching point in the maximum scale load.; Dosing operation; Press the F key to continue the dosing operation.; Ending the dosing operation
English 1 17 7 Select the dosing function in Setting mode (see separate description470.702.078 User Mode and 470.051.109 Dosing). Use the switching points (see 3.6) to set coarse flow, fine flow and correctionvalue. Setting the switching points S1 Setpoint for coarse dosingS2 Setpoint for fine dosin...
Page 18 - Troubleshooting; Part weight too small.
English 1 18 8 4 Troubleshooting Display Remedy Please check that you operated theappliance correctly. If not, interruptthe command chain by pressing theCL key. The scale sets the value zero auto-matically when it is switched on. Ifthe scale is outside the set toleranceband, the display indicates --...
Page 20 - F O R M E A S U R A B L E S U C C E S S; Phone
www.soehnle-professional.com F O R M E A S U R A B L E S U C C E S S Soehnle Professional GmbH & Co. KG Wilhelm-Soehnle-Straße 271540 Murrhardt Phone +49 (0) 71 92 / 93 19-220 Fax +49 (0) 71 92 / 93 19-2 11 E-Mail [email protected] S Sc ca al le es s, , S Sy ys st te em m S So ol lu u...
