Siemens SPC3 - User Manual

Siemens SPC3

Siemens SPC3 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
57 Page 57
58 Page 58
59 Page 59
60 Page 60
61 Page 61
62 Page 62
63 Page 63
64 Page 64
65 Page 65
66 Page 66
67 Page 67
68 Page 68
Page: / 68

Table of Contents:

  • Page 3 – S IM A T IC - N E T; S P C 3
  • Page 4 – PROFIBUS Interface Center; Page 2
  • Page 5 – SPC3 Hardware Description; Page 3; Release
  • Page 7 – TECHNICAL DATA
  • Page 8 – Page 6
  • Page 9 – Page 7; Introduction
  • Page 10 – Page 8; Function Overview; The processor interface supports the following processors:
  • Page 11 – Page 9; Pin Description; The SPC3 has a 44-pin PQFP housing with the following signals:; All signals that begin with X.. are LOW active; CMOS
  • Page 12 – CMOS with pull down
  • Page 13 – Memory Allocation; Memory Area Distribution in the SPC3; Address
  • Page 15 – Interrupt Controller Register; Figure 4.2: Assignment of the Internal Parameter Latches for READ
  • Page 19 – ASIC Interface
  • Page 20 – No special clear mode.
  • Page 22 – Status Register
  • Page 24 – Interrupt Controller; Bit Position
  • Page 28 – PROFIBUS-DP Interface; reserved
  • Page 29 – User
  • Page 30 – X1 See below for coding.
  • Page 31 – Description of the DP Services
  • Page 39 – Hardware Interface; Universal Processor Bus Interface
  • Page 41 – L o w C o st S yste m w ith 8 0 C 3 2
  • Page 46 – Technical Data; Maximum Limit Values; Permitted Operating Values
  • Page 47 – AC-Specification for the Output Drivers
  • Page 48 – Timing Characteristics; Clock pulse 48 Mhz :; CLK; TCLH
  • Page 55 – TBD
  • Page 56 – RTS
  • Page 58 – αα
  • Page 59 – PROFIBUS Interface
  • Page 60 – Example for the RS 485 Interface
  • Page 62 – General Definition of Terms; Ordering of ASICs
  • Page 63 – 1 Appendix A: Diagnostics Processing in PROFIBUS DP; Diagnostics Bits and Expanded Diagnostics
  • Page 65 – Diagnostics Processing from the System View
  • Page 66 – 2 Appendix B: Useful Information; Data format in the Siemens PLC SIMATIC; high byte
  • Page 68 – SIEMENS Aktiengesellschaft
Loading the manual

SIMATIC NET

SPC3 Siemens PROFIBUS Controller

Hardware Description

Date 2003/04/09





































"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - S IM A T IC - N E T; S P C 3

S IM A T IC - N E T (S ie m e n s P R O F IB U S C o n tro lle r a c c o rd in g to IE C 6 1 1 5 8 ) V e rs io n : 1 .3 D a t e : 2 0 0 3 /0 4 S P C 3 H a r d w a r e D e s c r ip tio n

Page 4 - PROFIBUS Interface Center; Page 2

PROFIBUS Interface Center SPC3 Page 2 V1.3 SPC3 Hardware Description 2003/04 Copyright (C) Siemens AG 2003. All rights reserved. Liability Exclusion W e have tested the contents of this document regarding agreement with the hardware and software described. Nevertheless, there may be deviations, and ...

Page 5 - SPC3 Hardware Description; Page 3; Release

SPC3 PROFIBUS Interface Center SPC3 Hardware Description V1.3 Page 3 Copyright (C) Siemens AG 2003 All rights reserved. 2003/04 Versions Release Date Changes V 1.1 12/23/99 Chapter 8.2 Current consumption without bus accesses Chapter 10.1 Contact persons V 1.2 09/25/02 Included the specification of ...

Other Siemens Models