Siemens HICOM Hicom 300 - User Manual
Siemens HICOM Hicom 300 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – here; Version Information; Date of Modification Details of Modification; Initial version of this document.
- Page 3 – Components Information; VoIP Gateway; Prerequisites; Gateway Requirements
- Page 4 – Configure the gateway to use the SIP VoIP protocol.
- Page 5 – PBX Setup Notes; Setting Up Each Gateway Station Port
- Page 7 – Defining Hunt Group and Coverage Path
- Page 8 – MWI considerations
- Page 9 – Exchange 2007 UM Validation Test Matrix; CP
- Page 11 – NT
- Page 12 – Detailed Description of Limitations
- Page 13 – Troubleshooting; Important Debugging Tools
- Page 14 – Appendix; Dial Pilot Number and Mailbox Login; Confirm successful logon to the user’s mailbox.; Navigate Mailbox using Voice User Interface (VUI); Navigate Mailbox using Telephony User Interface (TUI); Logon to a user’s UM mailbox.; Dial User Extension and Leave Voicemail; Confirm the voicemail message arrives in the called user’s inbox.
- Page 17 – To an External Phone number; Logon to the UM-enabled user’s mailbox in OWA.; Voicemail Button; Press this voicemail button on the phone of an UM-enabled user.
- Page 19 – Test Fail-Over Configuration on IP-PBX with Two UM Servers; Provide the configuration steps in Section 5.
1
M
M
i
i
c
c
r
r
o
o
s
s
o
o
f
f
t
t
E
E
x
x
c
c
h
h
a
a
n
n
g
g
e
e
S
S
e
e
r
r
v
v
e
e
r
r
2
2
0
0
0
0
7
7
U
U
n
n
i
i
f
f
i
i
e
e
d
d
M
M
e
e
s
s
s
s
a
a
g
g
i
i
n
n
g
g
P
P
B
B
X
X
C
C
o
o
n
n
f
f
i
i
g
g
u
u
r
r
a
a
t
t
i
i
o
o
n
n
N
N
o
o
t
t
e
e
:
:
S
S
i
i
e
e
m
m
e
e
n
n
s
s
H
H
i
i
c
c
o
o
m
m
3
3
0
0
0
0
w
w
i
i
t
t
h
h
D
D
i
i
a
a
l
l
o
o
g
g
i
i
c
c
®
®
1
1
0
0
0
0
0
0
M
M
e
e
d
d
i
i
a
a
G
G
a
a
t
t
e
e
w
w
a
a
y
y
S
S
e
e
r
r
i
i
e
e
s
s
(
(
D
D
M
M
G
G
1
1
0
0
0
0
8
8
D
D
N
N
I
I
)
)
u
u
s
s
i
i
n
n
g
g
D
D
i
i
g
g
i
i
t
t
a
a
l
l
S
S
e
e
t
t
E
E
m
m
u
u
l
l
a
a
t
t
i
i
o
o
n
n
By
:
Dialogic
Updated Since : 12/19/2007
READ THIS BEFORE YOU PROCEED
This document is for informational purposes only and is provided “AS IS”. Microsoft, its partners and
vendors cannot verify the accuracy of this information and take no responsibility for the content of this
document.
MICROSOFT, ITS PARTNERS AND VENDORS MAKE NO WARRANTIES, EXPRESS,
IMPLIED OR STATUTORY, AS TO THE INFORMATION IN THIS DOCUMENT.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Content This document describes the configuration required to setup Siemens Hicom 300 and Dialogic ® 1000 Media Gateway Series (DMG1008DNI) using digital set emulation as the telephony signaling protocol. It also contains the results of the interoperability testing of Microsoft Exchange 2007 Unifi...
3 1. Components Information 1.1. PBX or IP-PBX PBX Vendor Siemens Model Hicom 300 Software Version 9006.4SMR4 Telephony Signaling Digital set emulation Additional Notes N/A 1.2. VoIP Gateway Gateway Vendor Dialogic Corporation Model Dialogic ® 1000 Media Gateway Series (DMG1008DNI) Software Version ...
4 3. Summary and Limitations A check in this box indicates the UM feature set is fully functional when using the PBX/gateway in question. 4. Gateway Setup Notes During the initial setup of the gateway using the serial port, you must: • Assign the gateway a Unique IP address, subnet mask and network ...
