Siemens SIMATIC NET CP 343-1 - User Manual

Page 3 - Contents; Notes for the Reader; Compatibility with the Previous Version

english 1 Product information CP 343–1 C79000–Z8964–C038–05 Contents Notes for the Reader 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 The CP 343-1 Communications Processor 3 . . . . . . . . . . . . . . . 1.1 Characteristics 4 . . . . . . . . . . . . . . . . . ...

Page 4 - english; Safety Guidelines; Note; Danger

english 2 Product information CP 343–1 C79000–Z8964–C038–05 Notes for the Reader Safety Guidelines This manual contains notices which you should observe to ensure yourown personal safety, as well as to protect the product and connectedequipment. These notices are highlighted in the manual by a warni...

Page 5 - The CP 343-1 Communications Processor; Application; LED displays; Design; Double-width module for simple installation in the S7-300 rack.

english 3 Product information CP 343–1 C79000–Z8964–C038–05 1 The CP 343-1 Communications Processor Application The CP 343-1 communications processor is designed for operation in anS7-300 programmable logic controller. It allows the S7-300 to be attached toIndustrial Ethernet. LED displays Mode sele...

Page 6 - Configuration; Functionality of the CP 343–1; Characteristics; Services

english 4 Product information CP 343–1 C79000–Z8964–C038–05 Configuration You can configure the CP 343–1 via MPI or LAN/Industrial Ethernet. You re-quire STEP 7 with the following version of NCM S7 for Industrial Ethernet(abbreviated to ”NCM IE” below): Table 1 Version STEP7/NCM IE Functionality of ...

Page 7 - Extended Functions Compared with Version 5; Reading and writing data in the FETCH/WRITE mode; Requirements – General Operation; CPU

english 5 Product information CP 343–1 C79000–Z8964–C038–05 Note If there is a diagnostic connection to the CP via the CPU, configurationdata cannot be downloaded automatically to the CP by the CPU at thesame time! Extended Functions Compared with Version 5 S Reading and writing data in the FETCH/WR...

Page 8 - All versions of the SINUMERIK CPUs 840D and 810D are supported.; Requirements – ISO Transport Connections; Functionality; Note the two requirments below:

english 6 Product information CP 343–1 C79000–Z8964–C038–05 Table 2 CPU MLFB–Number CPU 614 6ES7 614–1AH03–0AB3 CPU 614–Z 6ES7 614–1AH03–0AB3–Z The table lists the CPUs approved at the time of printing this product informa-tion bulletin. S7–300 CPUs approved later and not listed in the table alsosup...

Page 9 - Performance Data; Characteristics of S7 Communication; Characteristic; Number of ISO transport connections; Reaction Times of ISO Transport Connections

english 7 Product information CP 343–1 C79000–Z8964–C038–05 1.2 Performance Data 1.2.1 Characteristics of S7 Communication The functions and characteristics of S7 communication are described in /8/and /11/. 1.2.2 Characteristics of ISO Transport Connections The following information is important for...

Page 10 - Component; Displays and Mode Selector; LED Displays; The LED panel on the front of the CP 343-1 has three display elements:; SF; CP Operating Mode; STOP–LED

english 8 Product information CP 343–1 C79000–Z8964–C038–05 Table 5 Component Explanation / Values Run time in the CPU 314-1 per block AG-SEND/AG-LSEND,AG-RECV/AG-LRECV2.5 ms to 5 ms 1.3 Displays and Mode Selector LED Displays The LED panel on the front of the CP 343-1 has three display elements: SF...

Page 11 - Controlling the Operating Mode

english 9 Product information CP 343–1 C79000–Z8964–C038–05 STOP–LED (yellow) CP operating mode SF–LED (red) RUN–LED (green) Module fault / system error Legend: lit off flashing Note Read the explanations of the operating modes in the NCM S7 forIndustrial Ethernet manual /8/. Controlling the Operati...

Page 12 - Further Information on Operation; Downloading Firmware; The CP 343-1 supports firmware updates using the Firmware Loader.; Group status “8183” on the FC call interface; The CP is in the STOP mode.

english 10 Product information CP 343–1 C79000–Z8964–C038–05 Note Read the sections about downloading configuration data to the CP in theNCM S7 for Industrial Ethernet manual /8/. 1.4 Further Information on Operation Downloading Firmware The CP 343-1 supports firmware updates using the Firmware Load...

Page 13 - Installation; Module Accessories

english 11 Product information CP 343–1 C79000–Z8964–C038–05 Status on the FC call interface; special situation with FC versions With the FCs AG_SEND (FC 5) and AG_RECV (FC 6), you receive the follo-wing return values after a connection is aborted: S AG_SEND: DONE=1; ERROR=0; Status=0000 H S AG_RECV...

Page 14 - Procedure; Steps in Installation; Installing the CP 343-1 involves the following steps.; via MPI

english 12 Product information CP 343–1 C79000–Z8964–C038–05 2.2 Procedure Steps in Installation Installing the CP 343-1 involves the following steps. S Plug in the CP 343-1 and secure it with the screws (make sure that thebus connector between the CPU/IM and CP 343-1 is present). S Attach the CP 34...

Page 15 - Attaching the CP 343-1 to Industrial Ethernet; The CP 343-1 can be attached to Industrial Ethernet using a

english 13 Product information CP 343–1 C79000–Z8964–C038–05 2.3 Attaching the CP 343-1 to Industrial Ethernet The CP 343-1 can be attached to Industrial Ethernet using a S Transceiver with an AUI interface Transceiver cable (drop cable) 727-1 Transceiver SF RUN STOP R STOP RUN CP 343–1 Figure 3 Att...

Page 16 - Optical Industrial Ethernet using an AUI attachment

english 14 Product information CP 343–1 C79000–Z8964–C038–05 ITP installationcable SF RUN STOP R STOP RUN CP 343–1 e.g Optical Switch Modul(OSM) SF RUN STOP R STOP RUN CP 343–1 Figure 4 Attaching the CP343-1 to Industrial Ethernet with TP/Optical Switch Module (OSM) or Hub S Optical Industrial Ether...

Page 17 - Technical Data; General Technical Data; Dimensions and Weight; Weight; Electromagnetic compatibility

english 15 Product information CP 343–1 C79000–Z8964–C038–05 3 Technical Data 3.1 General Technical Data Dimensions and Weight Dimensions, module in casing H x W x D (mm) 125x80x120 Weight approx. 750 g Voltage, Current, Operating Conditions Power supply 5 V DC +/– 5%24 V DC +/– 5% Current consumpti...

Page 18 - Pinout; Connector for Industrial Ethernet; Notes on the Pinout

SF RUN STOP R STOP RUN CP 343–1 english 16 Product information CP 343–1 C79000–Z8964–C038–05 3.2 Pinout Connector for Industrial Ethernet On the front panel of the CP 343-1, there is a 15-pin sub D female connectorwith a sliding locking mechanism for connecting a transceiver cable. Thesignals of an ...

Page 19 - Notes on the CE Approval of SIMATIC NET Products; Area of Application; The product is designed for use in an industrial environment.; Requirements; Industrial; Directive on Machines

english 17 Product information CP 343–1 C79000–Z8964–C038–05 3.3 Notes on the CE Approval of SIMATIC NET Products Product name: CP 343-1 Order number: 6GK7 343-1BA00-0XE0 EU Directive EMC89/336/EEC The SIMATIC NET products listed above meet the requirements of the EUdirective 89/336/EEC ”Electromagn...

Page 20 - References; SIMATIC NET Manual: Triaxial Networks for Industrial Ethernet; Order Numbers

english 18 Product information CP 343–1 C79000–Z8964–C038–05 4 References The following documentation is necessary for configuration and operationand contains detailed information: For installing and starting up the CP 343-1Manual: S7-300 Programmable Controller, Hardware and Installation For using ...

Page 21 - To; Our Industrial Ethernet application:; Suggestions for improvement are welcome on e-mail address

C79000-Z8974-C43-01 Mail / FAX Reply (Call ++911-978-3321) --- --- From Name ............................................................................. Position ............................................................................. Company .....................................................

Siemens SIMATIC NET CP 343-1 - User Manual

Table of Contents:

Summary

Other Siemens Models