Siemens ITE - User Manual

Siemens ITE

Siemens ITE – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.

1 Page 1
2 Page 2
3 Page 3
4 Page 4
5 Page 5
6 Page 6
7 Page 7
8 Page 8
9 Page 9
10 Page 10
11 Page 11
12 Page 12
13 Page 13
14 Page 14
15 Page 15
16 Page 16
17 Page 17
18 Page 18
19 Page 19
20 Page 20
21 Page 21
22 Page 22
23 Page 23
24 Page 24
25 Page 25
26 Page 26
27 Page 27
28 Page 28
29 Page 29
30 Page 30
31 Page 31
32 Page 32
33 Page 33
34 Page 34
35 Page 35
36 Page 36
37 Page 37
38 Page 38
39 Page 39
40 Page 40
41 Page 41
42 Page 42
43 Page 43
44 Page 44
45 Page 45
46 Page 46
47 Page 47
48 Page 48
49 Page 49
50 Page 50
51 Page 51
52 Page 52
53 Page 53
54 Page 54
55 Page 55
56 Page 56
Page: / 56

Table of Contents:

  • Page 3 – Table of Contents
  • Page 4 – *Authorized and qualified personnel—; in the proper care and use of protective equipment such as; is trained; in rendering first aid.; SUMMARY
  • Page 5 – Information and Instructions; General; General Information; Circuit Breaker Operation; NOTE: The lockable cover shield prevents unauthorized; Manual Operation
  • Page 8 – NOTE: This instruction page outlines the recommended; Installation of Breaker; To mount the device perform the following steps:; Figure 2
  • Page 9 – JD and LD-Frame Trip Adjustments
  • Page 10 – Function; Instantaneous Pickup; Figure 1
  • Page 12 – Ground Fault Pickup (I
  • Page 13 – NOTE: Do not spray or allow any petroleum based chemi-
  • Page 14 – JD and LD-Frame Time Current Curves
  • Page 18 – t Curve
  • Page 20 – General Description; One complete rear stud assembly requires the following:; Application Information; A. Remove wire connectors from breaker if present.; Important User Note
  • Page 21 – Installation, Diagrams
  • Page 22 – A . Remove pressure wire connectors from breaker if present.
  • Page 23 – Installation Diagrams
  • Page 24 – NOTE: Trip unit must be installed in circuit breaker prior to
  • Page 25 – not
  • Page 27 – NOTE: On shunt trip, undervoltage trip and auxiliary switch
  • Page 28 – Refer to Electrical Check, pages 27 and 28.; Recommended Combinations; Maximum Installable Accessory Combinations; Figure 4
  • Page 29 – Shunt Trip; Reset and turn circuit breaker ON.; Electrical Check; Electrical Data For Shunt Trip
  • Page 30 – I-T-E Auxiliary Switch and Bell Alarm Switch; Auxiliary Switch Kits; Switch Identification (All With Three Leads); Repeat Steps A through C using leads A1, B1 and C1; Bell Alarm Switch Kits
  • Page 32 – NOTE: Breaker must be “tripped” during installation. Push red; Handle Mounting
  • Page 34 – NOTE: Cut slots in terminal shields as shown to allow access
  • Page 36 – TM; Flange-Mount Handle Operator; Flange-Mount Handle Operator is a
  • Page 37 – INSTALLATION; With the enclosure door open/ the operat-
  • Page 38 – NOTE: When installed, the cable bend radius should not be
  • Page 39 – NOTE: Before attaching the cable to the circuit breaker,
  • Page 40 – Electric Motor Operator; NOTE: For automatic reset operation a separate auxiliary; Operator Selection; Installation
  • Page 41 – Close and latch the mechanism cover; Electrical Characteristics; Electrical Operation
  • Page 45 – NOTE: D and E dimensions are determined by the height of the; Adjusting the Mechanism; NOTE: To open the door when the handle is in the ON position,
  • Page 47 – A. Turn off power feeding this device before starting the; Incorrect usage of the neutral sensor transformer; Introduction; NOTE: The SJD and SLD series of electronic trip circuit
  • Page 48 – Terminal Connections
  • Page 51 – Ordering Information; Neutral Transformers; Circuit Breaker Catalog Numbers
  • Page 53 – Internal Accessory Combination; Undervoltage Trip
  • Page 54 – Additional Accessories
  • Page 55 – UL Listings and File Numbers; Industry Specifications; Lockable Cover Shield
Loading the manual

Bulletin SIB 2.7-7A

I-T-E

®

Molded Case

Circuit Breakers

Sensitrip

®

JD & LD-Frame
Information and
Instruction Guide

"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.

Summary

Page 3 - Table of Contents

I-T-E ® JD & LD-Frame Circuit Breakers 3-Pole, 200-600 Amperes Types SJD6, SHJD6, SLD6, SHLD6, SCJD6, SCLD6Digital Solid State Circuit Breakers Table of Contents Important Notices 2 General Information 3 Dimensional Reference Drawings 4,5 Installation Instructions 6 Operational Characteristics: ...

Page 4 - *Authorized and qualified personnel—; in the proper care and use of protective equipment such as; is trained; in rendering first aid.; SUMMARY

2 IMPORTANT The information contained herein is general in nature and is not intended forspecific application purposes nor is it intended as a training manual forunqualified personnel. Refer to Note for definition of a qualified person.* It does not relieve the user of responsibility to use sound pr...

Page 5 - Information and Instructions; General; General Information; Circuit Breaker Operation; NOTE: The lockable cover shield prevents unauthorized; Manual Operation

Information and Instructions 3 General JD and LD-Frame Solid State Sensitrip style breakers of theSentron family are for use in individual enclosures, switch-boards, and power distribution panel boards. They areavailable both as 80% and 100% rated devices and in threeinterruption ranges as shown in ...

Other Siemens Models