Siemens IGWIPS200-1 - User Manual
Siemens IGWIPS200-1 – User Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 4 – PREFACE; Symbol Meaning; will; Electrical shock hazard –
- Page 6 – INTRODUCTION; and; The terms remote and slave are used interchangeably in this guide.
- Page 8 – PRODUCT SUPPORT; IMPORTANT; Contact Information; United States
- Page 9 – INSTALLATION; Po
- Page 11 – CSA HAZARDOUS LOCATION PRECAUTIONS
- Page 12 – ANTENNA CONNECTORS AND SURGE VOLTAGE PROTECTION; Remote Site; Figure 2 Current (Amperage) Budget Example
- Page 14 – Pulse Input Module (See Figure 17 on page 26)
- Page 15 – Pulse Output Module (See Figure 18 on page 26); C. Setting Module Switches
- Page 16 – MOUNTING THE DIN RAIL; Conduit adapters; DIN Rail Mount Transceiver or I/O Expansion Module; Figure 3 Physical Dimensions
- Page 17 – Interconnect the modules by mating the bus connectors.; To add a module to a row:; Note the gender of the installed module’s bus connector.; To remove a module from the DIN rail:; on both sides
- Page 18 – WIRING; matched; DANGER; Remove power from all wires and terminals before working on; installation information may be provided with the antenna.
- Page 19 – Electrical Connections; Figure 5 Removing a Connector Block; Wire Stripping Recommendations:; Power Input Circuit Protection
- Page 20 – Transceiver Wiring Examples; Figure 6 Transceiver Wiring, 4-20 mA Current Loop with 2-Wire Device
- Page 21 – Figure 7 Transceiver Wiring, 4-20 mA Current Loop with 3-Wire Device
- Page 22 – Figure 8 Transceiver Wiring, 4-20 mA Current Loop with 4-Wire Device
- Page 23 – Figure 9 Transceiver Wiring, Analog and Digital Outputs
- Page 24 – Transceiver RF Link and Output State Wiring Options; Figure 11 Transceiver Block Diagram; I/O Expansion Module Wiring Examples
- Page 27 – Figure 16 Combination Input and Output Module Wiring
- Page 29 – ASSIGNING AND SETTING I/O MODULE ADDRESSES; Yellow; Figure 19 I/O Module Address Selection Switch
- Page 30 – or
- Page 31 – POST INSTALLATION SIGNAL STRENGTH AND LED INDICATIONS; TRANSCEIVER RSSI
- Page 32 – Figure 21 Received Signal Strength Graph; all; PULSE INPUT MODULE DIAGNOSTIC LED’S
- Page 33 – PULSE OUTPUT MODULE DIAGNOSTIC LED’S; frequency; SPECIFICATIONS; Transceiver; to specified voltage levels consult factory for relay options); LOS – Line of Sight between transmitting and receiving antennas
- Page 36 – WARRANTY
INSTALLATION GUIDE
IGWiPS200-1
Rev 3
May 2007
)
)
)
)
)
)
)
)
)
)
)
(
(
(
(
(
(
(
(
(
(
(
(
WiPS-200 Series
Wireless Process Solution
Frequency Hopping Spread Spectrum Radio
Two-Way (Multipoint-to-Point) for Monitoring and Control
With Expandable I/O Options
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
IGWiPS200-1 PREFACE CONVENTIONS AND SYMBOLS The following symbols may be used in this manual and may appear on the equipment. The reader should become familiar with the symbols and their meaning. Symbols are provided to quickly alert the reader to safety related text. Symbol Meaning DANGER Indicates...
IGWiPS200-1 INTRODUCTION This publication describes installation of the Siemens Wireless Process Solution (WiPS) 200 Series Two-Way Multipoint-To-Point Radios and I/O Expansion Modules. Radios (i.e. transceivers) 1 and I/O modules are used to construct a WiPS wireless network for the gathering and d...
IGWiPS200-1 PRODUCT SUPPORT When contacting Siemens for support: • Please have complete product information at hand: • For hardware, this information is provided on the product nameplate (part number or model number, serial number, and/or version). • For most software, this information is given in t...
