Page 5 - Basic; types
Basic information 1 Basic information SiPass standalone is a complete access control system for one door and up to 500 cardholders. SiPass standalone uses 125 kHz proximity technology. For gaining access, it is sufficient to hold the badge close to the reader. For programming purposes, an optional R...
Page 6 - Badge; badge
Badge type 3 Badge type 3.1 User badge User Can be used in ”Access” mode only. Special Can be used in both, ”Access” and ”Night lock” mode. 3.2 Master badge Program Master Master of masters Add Master Allows to introduce new badges to the systems memory Void Master Allows to delete (void) badges fro...
Page 7 - indicators; Overall
LED indicators 4 LED indicators Read indication (yellow)Open (green) Closed (red) Night lock (red)Add (red) Void (red)Program (red) Fig. 1 LED indicators 5 Overall time-out In Program Mode, after 30 seconds of inactivity, an error tone sounds, and normal operation resumes. 7 Siemens Building Technol...
Page 8 - Security; tag; vandal
Security measures 6 Security measures 6.1 Missing tag For safety precautions the user is strongly advised to keep records of the ID num-bers and functions of all badges and the names of their users. In case of loss, the specific badges can be voided from memory by entering the badge number on the Si...
Page 9 - Wake up: Declaring the Program Master
Wake up: Declaring the Program Master 7 Wake up: Declaring the Program Master When powering up a SiPass standalone for the first time, one selected badge must be presented, to be declared as the Program Master. The Program Master may be regarded as a kind of master of masters; it will be instrumenta...
Page 10 - Declaring
Declaring the masters 8 Declaring the masters SiPass standalone has 3 programming modes which need to be processed before normal operation. When going through these modes the first time, you can directly declare the re-spective masters. Read Open Closed Night lockAdd Void Program Program Master Read...
Page 11 - Change Program Master
Change Program Master 9 Change Program Master This procedure replaces the old Program Master by a new one. The old Program Master is thereby voided from the SiPass standalone memory and the new badge is declared as Program Master instead. This is helpful if e.g. an other Program Master than the norm...
Page 12 - Add new user badge
Add new user badge 10 Add new user badge Badges which shall be granted access must first be stored in the SiPass stand-alone memory. The Add Master allows new badges to be added which, from then on, will be granted access. Any badge can be added, except Master badges and badges which are already in ...
Page 13 - user
Void user badge 11 Void user badge Badges which shall be denied access must first be voided from the SiPass stand-alone memory. The Void Master allows badges to be voided which, from then on, will be denied access. Normal operation Read Open Closed Night lock Add Void Program Read Open Closed Night ...
Page 14 - Set Night Lock Mode
Set Night Lock Mode 12 Set Night Lock Mode In night lock mode, normal badges will not be granted access. Only Special User Badges are granted access in this mode. Night Lock Mode is switched on with the Night Lock Master Night Lock Mode Normal operation Read Open Closed Night lock Add Void Program R...
Page 15 - Unset Night Lock Mode
Unset Night Lock Mode 13 Unset Night Lock Mode Only the Night Lock Master can switch Night Lock off. When presenting the Night Lock Master to unset Night Lock, access is granted at the same time. This function is intended for persons who are authorized to enable access for oth-ers, for example to un...
Page 16 - Add Special User Badge
Add Special User Badge 14 Add Special User Badge Special User Badges are granted access both, during Night Lock and during Nor-mal Operation. Unlike the Night Lock Master, they have no effect on Night Lock status. Special User Badges must be added by using the Add Master while SiPass stand-alone is ...
Page 17 - Declare Remote Programmer
Declare Remote Programmer 15 Declare Remote Programmer To store a Remote Programmer in the SiPass standalone memory, first show the Program Master to enter Program mode, then present the Remote Programmer while in Program mode. After this, SiPass standalone will resume its normal opera-tion. Read Op...
Page 18 - Void badge with a Remote Programmer
Void badge with a Remote Programmer 16 Void badge with a Remote Programmer Using a Remote Programmer, badges or Remote Programmers can be voided by their number. This is useful if badges or Remote Programmers are lost, stolen or damaged beyond use. For this reason it is important to keep records of ...
Page 19 - registration
Appendix 17 Appendix 17.1 Tag registration list ID Number Date Masters Program Master Void Master Add Master Nightlock Master Remote Programmers Users 19 Siemens Building Technologies Fire Safety & Security Products 02.2005
