Scotsman SCCP50MB-1SU - User Manual

Page 2 - Table of Contents

Introduction: This ice machine is the result of Scotsman’sdecades of experience as an industry leader in thedesign and manufacture of both commercial andresidential ice machines. This manual includes the information needed toinstall, start up and maintain the ice machine. Noteany Caution or Warning ...

Page 4 - Cabinet Layout

Cabinet Layout June 2008 Page 3 SCCG50 & SCCP50Installation and User's Manual

Page 5 - Air Intake

Air flow The machine takes in room temperature air at thelower right front and forces warm air out the lowerleft front. Restricting the airflow will adversely affect the ability of the ice machine to make ice. Clearance requirements: 0 inches at the top, 2inches at the rear and an 1/8 inch at each s...

Page 6 - Water Quality; built up mineral

Water Quality All water, including potable water supplied bymunicipalities, contains some impurities orminerals. Water absorbs impurities from the air asrain and/or as it flows through the ground. Some ofthe impurities are solid particles, these are knownas suspended solids, and a fine particle filt...

Page 7 - Door Covering; Door Panel; Installation and User's Manual

Door Covering Door Panel The ice machine is supplied without a conventionaldoor covering so it can be decorated to the user’spreference. Scotsman offers several coveringsincluding white, black and stainless steel. Inaddition, a custom built panel can be placed ontothe door. Door Panel Attachment To ...

Page 8 - Use Lower

SCCG50 & SCCP50 Installation and User’s Manual June 2008 Page 7 Door Panel Attachment Scotsman Door Panel Use Upper Hole at the Top Use Lower Hole at the Bottom Gasket Machine Screw Hole Plug Cover

Page 9 - Door swing change; Installation Notes; Built In Situations

Door swing change Note: Prior models had separate hinge bracketsand different directions to change swing. Moving the hinges allows the door to open fromeither the left or right side. Change swing beforeattaching door panel. To change: 1. Remove innermost screw holding each hingeto cabinet, loosen th...

Page 10 - Drain Pump Model drain installation

Installation: Water & Drain Water Supply, all models: The recommended water supply tubing is ¼ inch OD copper. Stainless steelflex or reinforced PVC tube may also be used.Install an easily accessible shut-off valve betweenthe supply and the unit. This shut-off valve shouldnot be installed behind...

Page 11 - Back View, Gravity Drain Model

Gravity Drain Caution: Restrictions in the drain system to themachine will cause water to back up into the icestorage bin and melt the ice. Gravity drain tubingmust be vented, have no kinks and slope to thebuilding drain. Air gaps are typically required bylocal code. 1. Place the ice machine in fron...

Page 12 - Electrical; Installation check list:

Electrical The ice machine is supplied with a power cord. Donot remove the grounding pin from the cord’s plug.Do not use extension cords. Follow all codes.Connect the machine to its own 115 volt, 15 ampcircuit. 1. If the electrical outlet for the ice maker isbehind the unit, plug in the unit. 2. Pos...

Page 13 - Use; What shouldn’t be done?; Normal cubes are tapered cylinders. If the cubes

Use No special instructions are needed for use. Justtake as much ice as you need, the machine willreplace it. A scoop is provided, and it can be stored in the machine using the loop of tubing on the rightside as a holder. That tubing is also the ice levelsensor; ice will fill the storage bin until i...

Page 14 - does not

Maintenance There are 5 things to keep clean: 1. The outside cabinet & door. 2. The ice storage bin. 3. The condenser. 4. The ice making system. 5. The ice scoop. How to clean the cabinet. Wipe off any spills on the surface of the door andhandle as they occur. If anything spilled on thedoor or g...

Page 15 - How to clean the condenser and winterize.; Condenser cleaning; Remove the kickplate and front service panel.; Winterizing; Note: Automotive antifreeze must NOT be used.

How to clean the condenser and winterize. Condenser cleaning The condenser is like the radiator on a car, it hasfins and tubes that can become clogged with dirtand lint. To clean: 1. Remove the kickplate and front service panel. 2. Locate the condenser surface. 3. Vacuum the surface, removing all du...

Page 16 - How to remove scale from the ice making system.; What to do before calling for service

How to remove scale from the ice making system. 1. Scoop out all of the ice, either discard it or saveit in an ice chest or cooler. 2. Press and HOLD the On/Off button in for 3seconds until the Green light goes out. 3. Press and HOLD the both the Clean-Reset andOn/Off buttons for 5 seconds. The Time...

Page 17 - SCOTSMAN ICE SYSTEMS; 01 Corporate Woods Parkway

17-3191-02 Rev. B SCOTSMAN ICE SYSTEMS 101 Corporate Woods Parkway Vernon Hills, IL 60061 800-726-8762 www.scotsman-ice.com

Scotsman SCCP50MB-1SU - User Manual

Table of Contents:

Summary

Other Scotsman Ice Makers Models