Page 2 - the many features of your Regency Fireplace.; INFORMATION FOR MOBILE/MANUFACTURED HOMES AFTER FIRST SALE
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 2 To the New Owner: Congratulations! You are the owner of a state-of-the-art Gas Stove by FIREPLACE PRODUCTS INTERNATIONAL. The P42 is a hand crafted appliance and has been designed to provide you with all the warmth and charm of a wood fireplac...
Page 3 - TABLE OF CONTENTS
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 3 TABLE OF CONTENTS Brick Panels ............................................................. 23Log Set Installation ................................................... 24Flush Door .................................................................
Page 4 - SAFETY LABEL; Copy of Safety Decal for P42
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 4 This is a copy of the label that accompanieseach P42 Zero Clearance Direct Vent GasFireplace. We have printed a copy of the con- SAFETY LABEL tents here for your review. The safety label islocated on the front inside base of the unit,visible w...
Page 5 - INSTALLATION
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 5 INSTALLATION IMPORTANT: SAVE THESE INSTRUCTIONS The P42-NG/P42-LP Direct Vent Fireplace mustbe installed in accordance with these instructions.Carefully read all the instructions in this manualfirst. Consult the "authority having jurisdict...
Page 7 - MANTEL LEG CLEARANCES; MANTELS; CLEARANCES; WARNING; Heat Release Kit
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 7 MANTEL LEG CLEARANCES Combustible mantel leg clearances as per diagram below: MANTELS Because of the extreme heat this fireplace emits, the mantel clearances are critical.Combustible mantel clearances from louver are shown in the diagram below...
Page 9 - EXTERIOR VENT TERMINATION REQUIREMENTS
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 9 EXTERIOR VENT TERMINATION REQUIREMENTS INSTALLATION . B B B B A C V V V V V V V A A V Fixed Fixed Openable Closed Closed Openable N L B E B M D F K H j V ertical T ermination V V ent terminal Area where terminal is not permited A Air supply ou...
Page 10 - VENTING; Regency Direct Vent System (Flex) Horizontal Terminations Only
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 10 INSTALLATION VENTING Regency Direct Vent System (Flex) Horizontal Terminations Only These venting systems, in combination withthe P42 Direct Vent Gas Fireplace, have beentested and listed as a direct vent heater systemby Warnock Hersey. The l...
Page 11 - RIGID PIPE VENTING COMPONENTS LIST
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 11 RIGID PIPE VENTING COMPONENTS LIST All Simpson Dura-Vent components are available directly from FPI. 946-506/P Vent Guard (Optional) 510-994 Rigid Pipe Adaptor (Must use with all Rigid Piping) 640-994 U37 Rigid Pipe Adaptor 640-530/P Riser Ve...
Page 12 - RIGID PIPE VENTING; Horizontal or Vertical Terminations; Wall Thickness Vent Length
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 12 Rigid Pipe Adaptor (Part# 510-994) Pipe Length Vertical Terminal Storm Collar Part # 953 Flashing 943 or 943S Ceiling Firestop (Part # 963) 24" Pipe Length Adj.Pipe Length 11" - 14-5/8" 90 Elbow o Horizontal Termination Cap Wall T...
Page 13 - RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 13 INSTALLATION RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS REGENCY DIRECT VENT SYSTEM (FLEX) (Propane & Natural Gas) The shaded areas in the diagram show all allowable combinations of vertical runs with horizontal terminations...
Page 14 - For All Horizontal Terminations
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 14 INSTALLATION RIGID PIPE VENTING ARRANGEMENTS - HORIZONTAL TERMINATIONS REGENCY DIRECT VENT SYSTEM (FLEX) - Propane & Natural Gas The diagram below shows examples of horizontal termination arrangements using two 90 o elbows. All Rigid Pipe...
Page 15 - RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 15 INSTALLATION RIGID PIPE VENTING ARRANGEMENTS - VERTICAL TERMINATIONS (Propane & Natural Gas) Note: Must use optional rigid pipe adap- tor when using rigid pipe ventsystems (Part # 510-994). Note: Regency Direct Vent System (Flex) is only ...
Page 17 - VERTICAL TERMINATION
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 17 Flex Liner Exhaust Flue A maximum of two certified joiner kits may be used per length. #948-305 (35 ft) Air Intake Co-linear DV Vertical Termination Cap # 946-529 Co-Linear Flex Adapter with Kit# 946-563 Outer Pipe with Kit# 946-563 Inner Pip...
Page 18 - Venting Arrangements - Vertical Terminations
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 18 INSTALLATION Venting Arrangements - Vertical Terminations with Co-linear Flex System for both Residential & Manufactured Homes into Masonry Fireplaces The shaded area in the diagrams showthe allowable vertical terminations.
Page 19 - Below Grade Installation; HORIZONTAL
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 19 INSTALLATION Below Grade Installation If the Snorkel Termination must be installedbelow grade, i.e. basement application, prop-er drainage must be provided to preventwater from entering the Snorkel Termination.Refer to Diagram 4.Do not attemp...
Page 20 - VERTICAL
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 20 6 ) Continue to assemble pipe lengths. Note: If an offset is necessary in the attic to avoid obstructions, it is impor-tant to support the vent pipe every3 feet (0.9 meter), to avoid exces-sive stress on the elbows, andpossible separation. Wa...
Page 21 - for Regency Direct Vent
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 21 INSTALLATION termination and slipping the 4"(100mm) linerover it at least 1-3/8" (35mm). Fasten withthe 3 screws (drilling pilot holes will makethis easier). Apply Mill Pac or high temper-ature silicone to the 6-7/8"(175mm) flexpi...
Page 22 - GAS LINE; GAS PIPE PRESSURE; System Data
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 22 GAS LINE INSTALLATION The gas line can be brought through either theright or the left side of the appliance. The gasvalve is situated on the right hand side of the unitand the gas inlet is on the right hand side of thevalve. Note: If the gas ...
Page 23 - AERATION
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 23 INSTALLATION AERATION ADJUSTMENT The aeration adjustment gears are located onthe valve mounting plate and are accessedfrom underneath through the bottom louveropening. To access the air shutter loosen the lock nutand then use the allen key to...
Page 24 - PROPANE; IMPORTANT
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 24 Burner tray without front logs in place All 3 logs in place PROPANE LOG SET INSTALLATION NATURAL GAS IMPORTANT For Propane Units - only place rockwool on the rear burner tray behind the burner tube. WARNING: Dangerous operatingconditions may ...
Page 25 - STANDARD
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 25 INSTALLATION Diagram 1 Diagram 3 STANDARD FLUSH DOOR The standard flush door comes with a blackframe. To install the frame, simply hook the topdoor flange onto the top of the unit and swingthe door towards the unit, diagram 1. Diagram 2 NOTE:...
Page 26 - BAY LOUVERS; OPTIONAL BAY DOOR; Optional Bay Trim
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 26 BAY LOUVERS 1 ) Install top louver by sliding the two bracket clips into the brackets located on top of thebay door. See below. The fitted louverleaves a small gap between faceplatebottom and louver top. Diagram 4 Diagram 3 Attach 4 supplied ...
Page 27 - FULL SCREEN FRONT; Backside of Full
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 27 INSTALLATION FULL SCREEN FRONT 2 ) Remove the Screen Doors from the Full Screen Door Frame by fully opening the doors and lifting up off of the hinges. See important notein step 9. Inside Top of Outer Frame 3 ) Full Screen Door Frame Installa...
Page 28 - Bottom Grill; Right Side
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 28 INSTALLATION Inner Cut-Outs BottomFlange NOTE: Should the finished wall protrude beyond the face of the unit,you can accommodate up to 1/2" depth. Simply push in the Full Screen Door Frame until it aligns against thefinished wall. Secure ...
Page 29 - Hinge
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 29 INSTALLATION 10) Close screen doors. 8 ) Slide the Top Grill into the louver brackets located on the inside top of the firebox. Push in place. Top Grill 9 ) Install the Left and Right Side Screen Doors in the fully open position by placing ov...
Page 30 - Power IN; WIRING DIAGRAM; Gas
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 30 4-7/16" Openings for electrical connections Power IN Millivolt Wires 5-1/2" 1-1/2" WIRING DIAGRAM CAUTION: Label all wiresprior to disconnectionwhen servicing controls.Wiring errors can causeimproper and dangerousoperation. No ele...
Page 31 - OPERATING INSTRUCTIONS; CAUTION; Thermostat Wire Table
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 31 OPERATING INSTRUCTIONS 1 ) Read and understand these instructions before operating this appliance. 2 ) Check to see that all wiring is correct and enclosed to prevent possible shock. 3 ) Check to ensure there are no gas leaks. 4 ) Make sure t...
Page 32 - COPY OF THE LIGHTING PLATE INSTRUCTIONS; FOR YOUR SAFETY READ BEFORE LIGHTING; DO NOT REMOVE THIS INSTRUCTION PLATE
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 32 COPY OF THE LIGHTING PLATE INSTRUCTIONS OPERATING INSTRUCTIONS 1 ) Push in the gas control knob slightly and turn clockwise to “OFF”. Do not force. FOR YOUR SAFETY READ BEFORE LIGHTING A ) This appliance has a pilot which must be lighted by h...
Page 33 - MAINTENANCE
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 33 2 ) Turn gas control knob so indicator points to "OFF" position and allow 5 minutes for any gas in the combustion chamber to escape. 3 ) Turn gas control knob counterclockwise so indicator points to the "PILOT" position. Depre...
Page 35 - REMOVING VALVE; REMOVING THE FAN
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 35 REMOVING VALVE 1 ) Shut off the gas supply. 2 ) Remove the louvers (and bay door if it is on). 3 ) Disconnect the inlet gas line. Note: Be sure to have an 11/16" wrench on the tee to ensure that the wholeline is not twisted 4 ) Disconnect...
Page 36 - INSTALLING VALVE
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 36 INSTALLING VALVE 12) Hook up the gas line and check for gas leaks with a soap and water solution or agas leak detector. (Do not use open flamefor leak testing.) 13) Fire up the unit. 14) Check the manifold pressure. 15) Reinstall the vermicul...
Page 37 - PARTS LIST; P42 MAIN ASSEMBLY
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 37 PARTS LIST P42 MAIN ASSEMBLY Part # Description Part # Description Part # Description 1 ) 910-142 Fan - Auto ON/OFFThermodisc 2 ) 820-389 Thermodisc Bracket 3 ) 948-045 Chain 4 ) 948-115 Extension Spring 7 ) 910-184 Terminal Block 8 ) 510-125...
Page 38 - P42 BURNER & LOG ASSEMBLY
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 38 PARTS LIST P42 BURNER & LOG ASSEMBLY Part # Description 602-574/P Valve Assembly - Natural Gas 602-576/P Valve Assembly - Propane 52) * Gasket - Valve Access Plate 56) 910-190 Piezo Ignitor & Nut 57) 910-378 Valve S.I.T. - Natural Gas...
Page 39 - P42 FLUSH DOOR & LOUVERS
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 39 P42 FLUSH DOOR & LOUVERS Part # Description 600-960 Flush Louvers (Set) - Gold/Black 600-958 Flush Louvers (Set) - Black 600-961 Flush Louvers (Set) - Steel/Black 133) * Flush Louver Assy-Top 134) * Flush Louver Assy-Bottom Flush Door Ass...
Page 40 - P42 BAY FRONT & LOUVERS
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 40 P42 BAY FRONT & LOUVERS 603-930 Bay Front Complete with Glass & Black Trim 106) 940-102/P Side Glass 107) 936-243 Glass Gasket 108) 940-101/P Center Glass 111) 602-906 Brick Panel - Bay Std Red 113) * Bay Door Trim (Each) -Black 602-9...
Page 41 - NOTES
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 41 _____________________________________________________________________________________ ____________________________________________________________ __________________________________________________________ ____________________________________...
Page 43 - WARRANTY
Regency P42-3 Zero Clearance Direct Vent Gas Fireplace 43 WARRANTY Regency Fireplace Products are designed with reliability and simplicity in mind. In addition, our internal Quality Assurance Team carefully inspects eachunit thoroughly before it leaves our facility. FPI Fireplace Products Internatio...
Page 44 - Installer: Please complete the following information; Printed in Canada
Installer: Please complete the following information Dealer Name & Address: ______________________________________________ __________________________________________________________________ Installer: ___________________________________________________________ Phone #: __________________________...
