Pioneer RM-V4000V - Manual

25 (1) Installing Ground 1 G r o u n d The ground must be flat and horizontal. It should be able to bear the weight of the system. For wooden floors, if the part receiving the weight of the system lies at the center between the reinforcement beams below the floor, the floor may become deformed or ma...

31 (11) Lighting • The projection screen kit (RMS-V4011/V5011) will not reflect like TV screens when exposed to external light, but may reflect if directly exposed to strong lights such as spotlight. Therefore, make sure that the screens are not exposed to direct spotlight. • For certain installatio...

34 2. INSTALLATION AND ASSEMBLY (1) Confirmation 1 Decide the position for installing the system according to the installation conditions in Chapter 3. Check Items [1] Dimensions of installing position, space at the back, distance to the ceiling [2] Floor flatness, strength, roughness [3] Position o...

39 (3) Carrying the Units After Opening Packaging To carry the screen unit and multi-projection unit after opening the packaging, hold them by the parts shown in the figure, and lift and move them. • Never drag the system along the floor when moving the units. • The lenticular sheet damages very eas...

41 (Fig. 3-13) H-shape frame assembly (L) 4 R i v e t 5 Shield 2 H-shape frame assembly (L) 1 Screw (M5 × 35) 1 Stopper Table 1 Base assembly B- 5 Guide fixture A- 5 Holder (R) A- 5 Holder (L) 2 H-shape frame assembly (R) 3 Horizontal frame assembly A- 7 B- 6 Screw (M5 × 35) 4. ASSEMBLING THE SYSTEM...

44 4 Multi Projection Unit (RM-V4000V/V5000V) The Multi-Projection Unit is designed to be mounted from the back of the cabinet normally. If sufficient space cannot be left at the back, it can be mounted from the front. (Fig.3-18) a When mounting from the back [1] Pull the table of the cabinet to the...

45 b When mounting from the front [1] Remove the two stoppers and two metal fixtures from the cabinet. (Fig. 3-23) [2] Pull the table to the front. [3] Insert the screws (M5 × 35) into the holes on the table. [4] Place the multi-projection unit on the table. [5] Attach the metal fixtures to the tabl...

46 5 Projection Screen Kit (RMS-V4011/V5011) [1] Mount the screen unit serving as the reference. Basically, mount from the center unit at the bottom. a If the number of units arranged are odd (E.g.: 3 × 3=9 screens) • Adjust the screen unit to the cabinet at the center of the bottom level and tempor...

53 INSTALLATION AND ASSEMBLY Screen 5. SPECIAL INSTALLATION (1) Wall inset • If removing the screen after installing the system, the person must go behind the screen (diagonally shaded part of the figure). Therefore when insetting the unit in the wall, careful take this into account before installat...

54 1. ADJUSTMENT PREPARATIONS (1) Wiring 1 Connection of Power Supply • The power supply can be connected to up to 3 units in a series using the AC outlets of Multi projection units. Connect the three units as one system to the external outlet. • The AC plug of Multi projection unit is a 3P with a g...

57 When TV SYSTEM=AUTO <VIDEO, Y/C Input) • Selects the convergence memory from MEMORY-1 or MEMORY-2 automatically according to the signals input (NTSC/PAL). <RGB Input> • Automatically selects the convergence memory as follows. For NTSC input:MEMORY 1 For PAL input:MEMORY 2 Horizontal freq...

61 Source Expanded NTSC Individual Y/C RGB Cube Input Function) By switching Y/C ↔ RGB, switches expansion/individual (video distortion is great) TV SYSTEM) Composite or Y/C signal system Fixed at NTSC RGB AUTO Converter data required for display) Composite signal system-One RGB-One 3. EXAMPLES OF M...

62 ADJUSTMENTS (3) When Switching Source Inputs to Multi Video Processor (1)- When using Pioneer's new Multi Video Processor Input Function) RGB TV SYSTEM) AUTO Converter data required for display) One *The phase difference of each input source can be adjusted at the Multi Video Processor side. *Whe...

64 (7) When Switching the Source Input to the Multi Video Processor Input Function: RGB TV SYSTEM: AUTO Converter data required for playing: Three For example, set as follows, and switch the data to input using RS-232C. Expanded NTSC:MEMORY 4 Personal computer 1:MEMORY 5 Personal computer 2:MEMORY 6...

65 ADJUSTMENTS 4. SCREEN ADJUSTMENTS (1) Adjustment Flowchart The following shows the order for performing the adjustments generally required in the setup of the multi-projection system. For details, see the descriptions on the next page and later. 1 Give ID ↓ 2 Adjust the size of each screen ↓ 3 Ad...

67 ADJUSTMENTS The & numbers correspond to the numbers in the flow- chart. 2 Adjustment signal input For adjusting size...Monoscope, etc.(EX.LD Test disc GGV1013, FRAME NO. 18001) For screen joining, linearity, color adjustment...Use adjustment signals such as , cross-hatch, etc. (EX.LD Test dis...

68 V PHASE (V STATIC when MULTI ON) 3 , 4 , 7 center adjustment Set to only green and adjust the center with V PHASE H PHASE . When MULTI ON, as V PHASE does not move, adjust it at the splitter side. If not possible, adjust with V STATIC H PHASE GH STATIC GV STATIC Only Green moves NOTE Do not adjus...

70 Explanation of H BLK L and H BLK R Adjustments H BLK L and H BLK R adjustments are performed to obtain the optimum convergence adjustment wave form when the display range changes due to changes in the H SIZE and frequency. Video signal Display range Convergence a d j u s t m e n t wave form Video...

74 ADJUSTMENTS 9 V SIZE adjustment Set to only green, observe the top part of the screen , and adjust the data amount in the vertical direction using V SIZE . Do not observe the bottom part of the screen. 8 H SIZE adjustment Set to only green, observe the right side of the screen , and adjust the da...