Page 3 - • IMPORTANT; Name of Assy; SIGNAL Assy; JIGS AND MEASURING INSTRUMENTS
195 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.1 INTRODUCTION • IMPORTANT When replacement of the following assemblies are required during repairs, be sure to replace the EEPROMs with the mounted ones in order toretain the adjustment data of the unit and to facilitate adjustment after the replacem...
Page 4 - ADJUSTMENT LOCATION AND ITEMS; Assembly Adjustment Location; Front View; SUB VIDEO ASSY; MEASURING METHOD; SERVICEMAN WARNING
196 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.3 ADJUSTMENT LOCATION AND ITEMS Assembly Adjustment Location DEFLECTION (SERVICE) ASSY Adjustment Items A CONV. AMP ASSY B DIGITAL CONV. ASSY Front View C Focus VR (VR1) Focus VR BGR CRT assy B DeflectionYoke (B) DeflectionYoke TP-BK TP-GK B CRT DRIVE...
Page 5 - Assembly Adjustment Location Guide
197 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 If POWER SUPPLY ASSY Brightness Adjustment ( ∗ 2) Focus Adjustment (VR1: FOCUS VR) ( ∗ 2) Screen Size Adjustment ( ∗ 2) Convergence Adjustment ( ∗ 2) White Balance Adjustment ( ∗ 2) 1 3 5 67 No adjustment is required is repaired or replaced If AV I/O AS...
Page 6 - Factory Adjustment Mode
198 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Start adjusting Selecting the mode for adjustment operations. Select 1st FACTORY ADJ mode, then adjust. Start Select 1st FACTORY ADJ Mode Start 1st FAC Factory Adjustment Mode Normalpicture Cyclically Front panel 2nd FAC-TORY ADJmodepicture 1st FAC-TORY...
Page 7 - OTHER OFFSET mode
199 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 OTHER OFFSET mode 1 2 3 4 5 To enter the OFFSET mode of each picture quality, use the following keys and codes of the remote control unit: Key(s) on the Remote Control Unit A STD OFFSET MODE DOWN C COMP (15 kHz) OFFSET MODE P in P CH-, SUB CH- D COMP (3...
Page 8 - Brightness Adjustment; Start
200 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 6.5 ADJUSTMENT Oscilloscope or 1 Brightness Adjustment Start 1st FAC (DOWN) Telop: Blue ADJUTMENT OFFSET CUTR Data value ADJUTMENT OFFSET : CUT-R 0 : CUT-G : CUT-B b b CH1 CH2 (X) (Y) Cut off level(180V DC) GND BRIGHT Black burst G CRTDRIVEASSY TP-GK 0 ...
Page 9 - Screen Center Adjustment
201 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 2 Deflection Yoke Lean Adjustment 2 Deflection Yoke Adjustment Start Cross hatch B.CRT DRIVEAssy CRT ASSY B CRT ASSY G CRT ASSY R Centering magnet(Turn in either direction until cross signal becomes white.) Deflectionyoke DeflectionYoke (L3) DeflectionY...
Page 10 - Focus VR Adjustment
202 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3 Focus Adjustment 3 -1 -2 Focus Adjustment of Lens Assy Start Cross hatch 3 Focus VR Adjustment Focus VR (VR1) BGR FOCUS VR Turn the Focus VR for best focusing. Cross hatch Lens assy(For Red) Lens assy(For Blue) Lens assy(For Green) "Best focusing&...
Page 11 - Test-cross Position Check
203 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 (LD player) DIGITALCONV. ASSY L1651 IC1410 IC1656 Start Test-cross Position Check 4 • Check the test-cross position. If it is located within ± 20 mm from the center of the screen, no adjustment is required. If it is not, adjust the position as follows: ...
Page 12 - Vertical Size Adjustment; or; Size Mode; st FAC; Data value; Picture Quality Mode H SIZE; Size mode; Table on H SIZE and V SIZE data
204 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 5 Vertical Size Adjustment -2 -1 1st FAC Start or Green screen V.SIZE 91% ± 2% INPUT TVGeneralbroadcasting Adjust the size so that the picture is completelydisplayed on the screen. 5 Size Mode 5 Screen Size Adjustment INPUT 1:Monoscope Note :Screen mode...
Page 13 - • Reference; Horizontal Size Adjustment
205 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 • Reference CH PRO-610HD SD-582HD5 PRO-510HD SD-532HD5 3 : H PHA (15K) 80 80 CH+ : H PHA (31K) 36 40 CH- : H PHA (33K) -14 -8 9 : H PHA (31K RGB) 26 30 0 : H PHA (33K RGB) -26 -20 The H PHASE adjustment is required if the left or right part of the scree...
Page 14 - CONVERGENCE ADJUSTMENT; Prior to Adjustment; Table 1 Input signal; Screen mode; Confirmation of convergence data; Convergence coarse adjustment
206 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 CONVERGENCE ADJUSTMENT 1. Procedures 1. When replacinf the DIGITAL CONV. Assy, replace the EEPROM of new DIGITAL CONV. Assy with the EEPROM of oldDIGITAL CONV. Assy. 2. Check the initial data for the convergence adjustment.3. Perform the coarse adjustme...
Page 15 - Coarse Adjustment of the Green
207 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 F RH STATIC 001 Screen indication The cross-hatch signal is generated inside the unit, and is auto-matically displayed in OFFSET CONVER. mode and MANUAL CONVERGENCE mode. You can turn on and off the cross-hatch signal with the YELLOW key. OFFSET CONVER ...
Page 16 - • Pattern for each adjustment item; GH
208 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 F (0 , 0) Screen indication A B F (4 , 4) Screen indication Screen mode:F : FULL Z : ZOOM C : CINEMA N : NATURAL H : FULL for HD The Screen modes change cyclically with each press of the SCREEN mode key. A Coordinates where the cursor (adjustment point)...
Page 18 - Coarse Adjustment of the Red; Numeric Key
210 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 2nd step Adjust so that the vertical lines become straight, taking care to preserve proper screen information volume and the linearity. Adjust the right half of the screen first, then the left half.(See 3.4.) 3rd step Adjust so that the horizontal lines...
Page 20 - Confirmation of Adjustment; Be sure NOT to change the green pattern during readjustment.; Contrast Adjustment; White Balance Adjustment
212 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3.6.5 Repeat procedures 3.6.2 through 3.6.4 for the other screen modes.(Completion of the red adjustment) 3.7 Coarse Adjustment and Fine Adjust- ment of the Blue Make coarse and fine-adjustments of the blue in the same manneras with the red, described i...
Page 22 - Adjustment Procedure of White Balnce; OFFSET Data Table; Color/Tint Adjustment
214 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 Adjustments are required for A, C, D, T, L, and V in the table above. Data in other parts are fixed. (I="0")Proceed with the adjustments in the following order: • First, perform "(1) STD OFFSET", then perform adjustments (2), (3) and (4)...
Page 24 - Panel Adjustment; Procedures
216 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 8 Panel Adjustment Start 1st FAC EDIT/ LEARN DTV SOURCE INFO RECEIVER 4 ¢ MENU INPUT AUDIO GUIDE 8 POWER POWER POWER VCR REC VOL VOL PROJECTION MONITOR RECEIVER REMOTE CONTROL UNIT Î TV/ DTV CBL /SAT DVD /LD VCR 1 4 7 5 8 6 9 2 3 0 ANT DISPLAY POWER MUT...
Page 25 - Size Adjustment of the Panel Part of the 4:3 Normal Screen
217 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 9 Panel Adjustment for DTV (PRO-610HD, PRO-510HD ONLY) Start 1st FAC EDIT/ LEARN DTV SOURCE INFO RECEIVER 4 ¢ MENU INPUT AUDIO GUIDE 8 POWER POWER POWER VCR REC VOL VOL PROJECTION MONITOR RECEIVER REMOTE CONTROL UNIT Î TV/ DTV CBL /SAT DVD /LD VCR 1 4 7...
Page 27 - GENERAL INFORMATION; DEFLECTION SERVICE Assy; How to diagnose a failure; POWER SUPPLY ASSY; DEFLECTION SERVICE ASSY; SIDE A
219 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 7. GENERAL INFORMATION 7.1 DIAGNOSIS 7.1.1 DIAGNOSIS METHOD Various protection circuits are provided for this unit. When theseprotection circuits are activated, the power of the unit is shut down(P.D.: Power Down).The defective parts can be easily diagn...
Page 28 - LEDs are lit by the HOLD circuit.
220 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 1. P.D. (1) Failure in the POWER SUPPLY Assy and the AUDIO Assy.There are four main possibilities:1. Abnormality in the regulator of the heater2. Blown fuse(s) in secondary3. Abnormality in RELAY (RY102)4. Abnormality in AUDIO OUTPUT Status Causes Check...
Page 29 - If the FU202 and FU204 fuses are blown, see the following table:; Causes
221 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 3. P.D. (3) Failure in the CONV. AMP AssyThe following reason may be suspected:1. V. deflection stopping detection Status Causes Check Items Probable Defective Parts D923, P.D. LED, lit V. deflection stopping Check that the connectors (G1, G2, G3) of th...
Page 30 - Block Diagram of the Protection Circuit
222 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 P POWER SUPPLY ASSY(AWV1795 :ELITE)(AWV1808 :REGULAR) Q POWERSW ASSY(AWZ6467) SIGNAL ASSY(AWV1800 :ELITE)(AWV1805 :REGULAR) A VIDEO ASSY(AWV1799 :ELITE)(AWV1804 :REGULAR) E D915 4. Block Diagram of the Protection Circuit
Page 32 - How to remove the screen (for adjusting Lens assemblies)
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 224 7.1.2 DISASSEMBLY Screen Frame 1 1 2 ∗ ∗ Screen SideFitting Screen SideFitting For SD-582HD5 andSD-532HD5 For SD-582HD5 andSD-532HD5 Loosen two screws Upper Cabinet Metal 3 3 5 Loosen a screw Remove a screw Remove UpperCabinet Metal 4 3 3 Note ∗ : Scree...
Page 33 - Disconnect the Anode Cable
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 225 Lens Assy (Green) Lens Assy (Blue) Lens Assy (Red) 6 Slide the screen to right, andadjust the focus of the lens. Notes:To assemble the screen, perform the above procedures in reverseorder.After assembling it, verify that the right and left sides of the ...
Page 34 - Front Section; FBT Focus Wire
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 226 7.1.3 WIRING DIAGRAM Front Section Focus VR (VR1) Focus VR FBT Focus Wire At least 15 mm away fromany other parts. Binder Binder CRT Assy (R) CRT Assy (G) CRT Assy (B) R. CRT DRIVE Assy G. CRT DRIVE Assy B. CRT DRIVE Assy
Page 35 - Rear Section
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 227 Rear Section Loop with a radius of50mm or more. At least 15mm away fromany other parts. Loop with a radius of 30mm or more. POWER SUPPLY Assy POWER SUPPLY Assy DEFLECTION SERVICE Assy VIDEO Assy Block CONV. AMP Block Ferrite Core Ferrite Core Ferrite Co...
Page 37 - Pin Function
229 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 . o N e m a N n i P O / I n o i t c n u F n i P . o N e m a N n i P O / I n o i t c n u F n i P 1 D D V D − V 3 . 3 + r o V 5 + y l p p u s r e w o p l a t i g i D 1 4 D D V A − V 5 + y l p p u s r e w o p g o l a n A 2 D D V D − 2 4 D D V A − 3 0 B O )...
Page 38 - Block Diagram
230 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 MB40958PFQ (SUB VIDEO SERVICE ASSY : IC3602) (PRO-610HD, PRO-510HD ONLY) • D/A Converter • Block Diagram InputBuffer MasterSlaveF•F 8 Buffer 8 CurrentSW 8 VCCA 46 4 8 9 5 6 7 (MSB) R1 1 CLKR R2 R3 R4 R5 R6 10 11 R7 (LSB) R8 ROUT InputBuffer MasterSlaveF...
Page 52 - • 128Kbit CMOS Serial EEPROM; No. Pin Name Pin Function
244 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 24LC128(I)P (DIGITAL CONV. ASSY : IC1410) • 128Kbit CMOS Serial EEPROM I/O CONTROL LOGIC MEMORY CONTROL LOGIC EEPROM ARRAY (2X256X8) or (4X256X8) XDEC PAGE LATCHES YDEC HV GENERATOR SENSE AMP R/W CONTROL 5 7 SDA A0 A1 A2 VSS VCC WP SCL SDA 1 8 VCC 4 VSS...
Page 55 - • 32Kbit CMOS Serial EEPROM; • Video Filter IC
247 PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 24LC32A(I)P (SIGNAL ASSY : IC2454) • 32Kbit CMOS Serial EEPROM I/O CONTROL LOGIC I/O MEMORY CONTROL LOGIC EEPROM ARRAY XDEC PAGE LATCHES YDEC HV GENERATOR SENSE AMP R/W CONTROL 5 7 SDA A0 A1 A2 VSS VCC WP SCL SDA 1 8 VCC 4 VSS SCL WP 3 A2 2 A1 1 A0 6 2 ...
Page 62 - Front panel
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 254 7.3 EXPLANATION CONNECTING VIDEO/AUDION EQUIPMENT INPUT jacks There are 4 sets of inputs for VCR and DVD/LD players. UseRCA-type pin plug cords (the same as those used in Hi-Fisystems) for connections. When the audio source to beconnected is monaural, c...
Page 63 - Rear panel; SIGNAL; Digital tuner; TO WATCH TV; Press the MUTING button.; Auto power off function
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 255 NOTE:Setting the INPUT 3 SELECT switch to ‘RGB’ will cause all S-Videoand composite images input from the INPUT 3 jack to besuppressed. Similarly, setting the INPUT 3 SELECT switch to ‘S-VIDEO/VIDEO’ will cause all images input from the RGB input jackto...
Page 67 - When blocking is on during SEARCH screen mode, the; If you forget the password; CHANGING PASSWORD
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 259 9 After setting, press MENU to turn themenu off. HOW TO REMOVE BLOCKINGFROM A PROGRAM IN PROGRESS When a selected program or a program on a channel to whichyou have just changed has a rating higher than the currentprogram blocking rating, the picture an...
Page 68 - Press the SPLIT button.; Regular operations can be performed on the main picture.; Press the FREEZE button.; This function is operable only with the normal screen.; MULTI-SCREEN FUNCTION
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 260 VIEWING TWO SCREENS (SPLIT screen) The screen can be split vertically, making it possible to view different imageson the left and right. Press the SPLIT button. • The screen on which is displayed is the main picture, and the otherscreen is the sub-pictu...
Page 69 - Press the SEARCH button.; Normal screen/SPLIT screen
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 261 • Pressing the MENU button in SEARCH screen mode restores the screen display to normal and displaysthe menu on screen. • These functions cannot be used while watching a DTV broadcast using the SH-D09 digital tuner (soldseparately). • These functions can...
Page 70 - Convergence adjustment may be fined-tuned from here.; Adjust the center point convergence.; Select the adjust point.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 262 Convergence adjustment may be fined-tuned from here. 2 Adjust the center point convergence. 1 Press MENU and select SET UP byusing the 5 or ∞ button and then pressing SET/ENTER. 3 Select ADJ MULTI-POINT . SET/ ENTER 4 Select the adjust point. SET/ ENTER...
Page 71 - Adjust the blue line.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 263 • The brackets which shows the adjusting point will move inorder.Move to the next point to be adjusted, and repeat steps 4 to 6. 7 After completing the convergenceadjustment, press MENU to turn themenu off. 6 Adjust the blue line. SET/ ENTER
Page 72 - SPECIAL NOTES; Picture Adjustments; Picture Quality setting:; Sound Adjustments; Surround Mode setting:; Changing Screen Mode
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 264 SPECIAL NOTES MOVIE or GAME mode may not be selected when receiving RGBinput. GAME mode setting: • All signals output from the Projection Monitor will be unaffected.Only the original output signal is sent through the output jacks. Picture Adjustments • ...
Page 74 - PANEL FACILITIES AND SPECIFICATIONS; PANEL FACILITIES for PRO-610HD and PRO-510HD
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 266 8. PANEL FACILITIES AND SPECIFICATIONS A flip-down door conceals the control panel. Push gently andrelease, to open the door. To close the door, lift it back up intoplace. NOTE:If you accidentally pull the door, it may not shut properly. Pushthe door ba...
Page 75 - RETURN button; Initial mode; VOLUME buttons
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 267 8 RETURN button Press to set the Projection Monitor to its initial mode. Initial mode Input selector: Set to TV. TV channel: Remains at the last channel set. VOLUME: Remains at the last setting. MUTING: OFF PICTURE MODE: STD Parameters: Set to 0. 3D Y/C...
Page 76 - Press to activate the selected function.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 268 Set the mode switch to TV/DTV. 1 TV POWER button (STANDBY/ON)Turns the power of the monitor on and off. 2 Input Selector buttons (TV, DTV* 1 , INPUT 1 to INPUT 4) Press the button to select the source you wish to watch.The screen will display your selec...
Page 80 - Set the mode switch to TV.
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 272 REMOTE CONTROL UNIT (AXD1449: CU-SD111) for SD-582HD5 and SD-532HD5 Set the mode switch to TV. 1 TV POWER button (STANDBY/ON)Turns the power of the monitor on and off. 2 Input Selector buttons (TV, INPUT 1 to INPUT 4)Press the button to select the sourc...
Page 82 - SPECIFICATIONS for PRO-610HD and PRO-510HD; Display and amplifier section
PRO-610HD, PRO-510HD, SD-582HD5, SD-532HD5 274 SPECIFICATIONS for PRO-610HD and PRO-510HD Display and amplifier section Reception system ........ American TV standard NTSC systemScreen size ................................................. 58" (PRO-610HD) 53" (PRO-510HD) CRT ...................
