Pioneer PDP-425CMX - Manual

Page 2 - About the RS-232C Adjustment; efer to; pg. 111 in the Technical Manual

2 RS-232C Adjustment This display has an RS-232C terminal. It is possible to use a PC to make various adjustments and settings. 1.1 About the RS-232C Adjustment Adjustments using the RS-232C: • The adjustments are written to the same memory area as for the integrator mode (refer to section 5.4.4, “P...

Page 3 - Interface; Note; From the PC to the display; From the display to a PC

3 RS-232C Adjustment 1.2 Interface 1) Connector D-sub 9 pins (male/straight) 2) Pin layout 3) Baud Rate 9600 bps (standard)(switch-able to 1200, 2400, 4800, 19200, 38400 bps) Note The baud rate of this display should be set to match the baud rate of the PC.Also, when the RS-232C cable is extended ov...

Page 4 - Combination Connection; displays at the same time or separately.

4 RS-232C Adjustment 1.3 Combination Connection When controlling/adjusting panels, it is convenient to connect several displays to one PC. By performing a combination connection and assigning IDs to the panels, it is possible to control and adjust several displays at the same time or separately. Con...

Page 5 - ID Assignment; Refer to section “Combination cables” for details.; Precautions when assigning IDs

5 RS-232C Adjustment 1.4 ID Assignment The ID is assigned from the PC. Commands: <IDC> (ID CLEAR) ........ Clears the assigned ID <IDS> (ID SET) ............. Assigns an ID IDS is only effective when an ID is not assigned. IDs are assigned starting from the panel closest to the PC. Examp...

Page 7 - List of RS-232C Commands; Normal Operation Related Commands

7 RS-232C Adjustment 1.5 List of RS-232C Commands 7 Normal Operation Related Commands Command Function Number direct Last Effective Minimum Maximum memory POWER POF Turns the power OFF. PON Turns the power ON. INPUT SELECT INPS01 Switches the main screen to INPUT1. INPS02 Switches the main screen to...

Page 8 - “MENU”–“SET UP” related commands

8 RS-232C Adjustment 7 “MENU”–“SET UP” related commands Command Function Number direct Last Effective Minimum Maximum memory COLOR TEMP. CTPS01 Sets the color temperature to LOW. CTPS02 Sets the color temperature to MID LOW. CTPS03 Sets the color temperature to MIDDLE. CTPS04 Sets the color temperat...

Page 11 - “INTEGRATOR”–“OPTION” related commands

11 RS-232C Adjustment Command Function Number direct Last Effective Minimum Maximum memory SCREEN MASK FMKS00 Sets SCREEN MASK to OFF. FMKS02 Sets SCREEN MASK to inverse (negative – positive reversed). FMKS03 Sets SCREEN MASK to white mask. FMKS04 Sets SCREEN MASK to red mask. FMKS05 Sets SCREEN MAS...

Page 13 - Other commands; QUEST Commands; Notes

13 RS-232C Adjustment Command Function Number direct Last Effective Minimum Maximum memory DISPLAY CALL DITS01 Displays DISPLAY CALL 1. DITS02 Displays DISPLAY CALL 2. IM0 INFORMATION write-in (1-3 characters). IM1 INFORMATION write-in (4-6 characters). IM2 INFORMATION write-in (7-9 characters). IM3...

Page 14 - ) Obtaining QST Status Information; Sequence

14 RS-232C Adjustment 1) Obtaining QST Status Information Sequence Data Content Size Remarks 1 STX 1 Byte 02hex 2 Command echo-back 3 Byte QST (fixed) 3 Generation information 1 Byte 5 (fixed) 4 Inch information 1 Byte 4 (fixed) 5 Forwarding 1 Byte M (fixed) 6 Power source state 1 Byte S: Standby st...

Page 19 - Check Sum; A detailed example is given below.; Examples of check sum applications; When the data is missing 1 Byte; When 1 Byte of data in the data is unreadable

19 RS-232C Adjustment 7 Check Sum This is data to which 2-Byte ASCII code is added to a data group returned by a QUEST command. STX 02 (hex) 2 Byte 3 Byte 03 (hex) ID QUEST command ETX STX 02 (hex) QUEST command 3 Byte Data *Byte Check sum 2 Byte ETX 03 (hex) PC side Set side A detailed example is g...

Page 20 - projection method, system configuration etc.; Menu mode; An inverse or full mask signal appears on the screen.; Menu Mode and Integrator Mode; Auto Brightness Adjustment (still image detection)

20 Screen Burning 2.03.0 Screen Burning When the same image is reproduced for a long period (still image, telop, etc.), the image is burned into to screen. It may be difficult to remove this image. Burning should be managed by making necessary changes in the video software, projection method, system...

Page 21 - Precautions on Connecting Camera Images; the panel and reduce the life or be the cause of other issues.

21 3.0 Precautions on Connecting Camera Images Connecting and using moving images that are nearly still, such as images from a surveillance camera, could damage the panel and reduce the life or be the cause of other issues. In this situation, it is necessary to set the image quality beforehand. For ...

Page 22 - Self-diagnosis Function; Precautions; Error Message

22 5.0 Precautions 1) If the power shuts down and stays OFF for a long period, an internal problem has probably occurred (failing part, etc.). Turn OFF the main power switch on the Plasma Display then wait 1 to 2 minutes and try turning the power ON again. If the power goes OFF again, the display ne...

Page 23 - Maintenance; Name; ) Readjustment of the White Balance

23 Maintenance Name Part Number Cleaning cloth: Wiping cloth AED1285 Cleaning cloth: Minimax GED-009 Cleaning liquid: B4 GEM1004 1) Be sure to unplug the power cord from the power outlet before performing maintenance. 2) Cabinet and Remote-control Unit Never use solvents such as benzene or thinner. ...

Page 24 - RS-232C Command Reference Manual; Industrial Solutions Business Group

PDP-425CMX RS-232C Command Reference Manual Pioneer Electronics (USA) Inc. Industrial Solutions Business Group 2265 East 220 th Street Long Beach, California 90810 United States of America (310) 952-2000 http://www.pioneerelectronics.com

Pioneer PDP-425CMX - Manual

Table of Contents:

Summary

Other Pioneer Models