Page 2 - Table of Contents; Features; Trip Data Acquisition
2 EN Table of Contents Features ................................................................................................................... 2Important Safety Information ................................................................................... 3Before Use (Important) .................
Page 3 - Important Safety Information; Important Information About This Device
3 EN Important Safety Information Pioneer Speed & Cadence Sensor is not a medical device. Important Information About This Device This device helps provide feedback about cycling. It is intended solely for recreational purposes. THE LIMITED WARRANTY PROVIDED WITH THIS DEVICE CONSTITUTES THE EXCL...
Page 4 - WARNING
4 EN Important Safety Information WARNING BEFORE BEGINNING OR • MODIFYING ANY EXERCISE ACTIVITY, ALWAYS CONSULT YOUR PHYSICIAN FIRST. IF YOU ARE USING A PACEMAKER OR ANY OTHER IMPLANTED DEVICE, CONSULT YOUR PHYSICIAN BEFORE USING A HEART RATE SENSOR.THIS PRODUCT IS NOT A • MEDICAL DEVICE, AND COULD ...
Page 5 - CAUTION
5 EN Important Safety Information Before riding, check that the sensor • and magnets are installed securely. Also check that the speed detector arm’s screw is not loose, there are no cracks in the band, and the band’s fixing tape is not coming off. Do not leave this device in places • that are expos...
Page 7 - IMPORTANT NOTICE
7 EN Important Safety Information [For American Users] IMPORTANT NOTICE KEEP WARRANTY CARD IN A SAFE PLACE FOR FUTURE REFERENCE.This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this d...
Page 8 - Operating Environment
8 EN Important Safety Information [For Canadian Users] This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference ...
Page 9 - Safety Precautions; DANGER
9 EN Before Use (Important) Safety Precautions DANGER About this Device Do not throw this device, strike it • with a hammer or other object, or pierce this device in any way.Do not use or leave this device in • places where it will be exposed to extremely high temperatures, such as near a stove or f...
Page 10 - Observe the following precautions
10 EN Before Use (Important) CAUTION Do not recharge, disassemble, heat • or dispose of the battery in fire.Use a CR2032 (3 V) lithium battery • only. Never use other types of batteries with this unit.Do not handle the battery with • metalic tools. Do not store the battery with metallic • materials....
Page 13 - Part Names and Functions; Front View
13 EN Part Names and Functions Front View Cadence sensor Detects the cadence magnet installed on the crank. LED for cadence magnet detection Blinks green when it detects the magnet just after the sensor is activated. LED for speed magnet detection Blinks red when it detects the magnet just after the...
Page 14 - Installation on Your Bike; Mount the Speed & Cadence sensor, cadence magnet, and speed magnet on; Remove the pedal from the
14 EN Installation on Your Bike Mount the Speed & Cadence sensor, cadence magnet, and speed magnet on your bike. Pairing with the cyclocomputer may not be possible due to the influence of the ● 2.4 GHz frequency band. If pairing fails, try again someplace where there is no interference from micr...
Page 15 - Installing the; Temporarily mount the Speed
15 EN Installation on Your Bike Installing the Speed & Cadence Sensor 1. Temporarily mount the Speed & Cadence sensor on the chain stay. Hook the band on the hook located on the back side of the sensor, and then put the band in the groove on the front side to temporarily mount the sensor on ...
Page 16 - Installing the Speed Magnet; Loosen the screw of the
16 EN Installation on Your Bike After blinking 10 times, the LED will • not light even though the sensor detects the magnet. The LED starts blinking again if you re-install the sensor’s battery or wait at least 20 minutes after the last time the sensor detects the magnet. Installing the Speed Magnet...
Page 17 - Adjust the angle of the speed
17 EN Installation on Your Bike The magnet can be installed on a • spoke that is from about 1.5 mm up to 2.5 mm in diameter. The magnet cannot be installed securely • on some spokes’ shapes. Confirm the spoke’s shape when installing it. Installing the magnet may damage • the spoke. Protect the spoke...
Page 18 - Fixing the Sensor
18 EN Installation on Your Bike Fixing the Sensor After installing the Speed & Cadence sensor, cadence magnet, and speed magnet, pair the sensor with the Cyclocomputer SGX-CA500 or other cyclocomputer, and confirm that the cadence is displayed with the rotation of the crank, and the speed is dis...
Page 19 - Install the new battery
19 EN 1. Remove the battery cover of the Speed & Cadence sensor. Turn the cover counterclockwise with a tool such as a coin or screwdriver, until it stops turning. 2. Remove the old battery. Installing and Removing the Battery The battery is pre-installed to this product. If the battery is almos...
Page 21 - Troubleshooting; If you have problems with your device, check the following items.
21 EN Troubleshooting If you have problems with your device, check the following items. If a solution to your problem cannot be found here, contact your dealer. Speed & Cadence sensor information is not displayed on the cyclocomputer. / ■ I cannot pair the sensor with the cyclocomputer. Cause So...
Page 22 - Specifications; Operation temperature:
22 EN Specifications Weight: Sensor: About 24 g Dimensions: Sensor: 36 mm(W) x 42 mm (H) x 16.5 mm(D) Water resistant: This device is water resistant to 6 m. Communications method (sensors): ANT+ wireless Battery: CR2032 Operation temperature: -10 to 60°C Estimated usable period: About 3 years (at o...
