Pioneer DEH-P4770MP - Manual

60

°

6

182

53

1

2

3

4

DEH-P4770MP

5

Fig. 4

¥ qJA«

8

9

11

10

7

Note:

•

Before making a final installation of the unit,
temporarily connect the wiring to confirm that
the connections are correct and the system works
properly.

•

Use only the parts included with the unit to
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.

•

Consult with your nearest dealer if installation
requires the drilling of holes or other modifica-
tions of the vehicle.

•

Install the unit where it does not get in the dri-
ver’s way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.

•

The semiconductor laser will be damaged if it
overheats, so don’t install the unit anywhere hot
— for instance, near a heater outlet.

•

If installation angle exceeds 60° from horizontal,
the unit might not give its optimum performance.
(Fig. 1)

•

When installing, to ensure proper heat dispersal
when using this unit, make sure you leave ample
space behind the rear panel and wrap any loose
cables so they are not blocking the vents.

DIN Front/Rear-mount

This unit can be properly installed either from
“Front” (conventional DIN Front-mount) or
“Rear” (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following illustrated
installation methods.

DIN Front-mount

Installation with the rubber bush (Fig. 2)

1. Dashboard
2. Holder

After inserting the holder into the dashboard,
then select the appropriate tabs according to the
thickness of the dashboard material and bend
them.
(Install as firmly as possible using the top and
bottom tabs. To secure, bend the tabs 90
degrees.)

3. Rubber bush
4. Screw

Removing the Unit (Fig. 3) (Fig. 4)

5. Frame

To remove the frame, extend top and bottom of
the frame outwards in order to unlock it. (When
reattaching the frame, point the side with a
groove downwards and attach it.)
• It becomes easy to remove the frame if the

front panel is released.

6. Insert the supplied extraction keys into the unit,

as shown in the figure, until they click into place.
Keeping the keys pressed against the sides of the
unit, pull the unit out.

DIN Rear-mount

Installation using the screw holes on
the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)

1. Remove the frame.

7. Frame

To remove the frame, extend top and bottom of
the frame outwards in order to unlock it. (When
reattaching the frame, point the side with a
groove downwards and attach it.)
• It becomes easy to remove the frame if the

front panel is released.

2. Fastening the unit to the factory

radio mounting bracket.

8. Select a position where the screw holes of the

bracket and the screw holes of the head unit
become aligned (are fitted), and tighten the
screws at 2 places on each side. Use either truss
screws (5

×

8 mm) or flush surface screws

(5

×

9 mm), depending on the shape of the screw

holes in the bracket.

9. Screw
10. Factory radio mounting bracket
11. Dashboard or Console

Installation

<ENGLISH>

Fig. 2

≤ qJA«

Fig. 1

± qJA«

Fig. 3

≥ qJA«

Fig. 5

µ qJA«

Fig. 6

∂ qJA«

Fig. 7

∑ qJA«

INST

ALLA

TION MANUAL

INST

ALLA

TION MANUAL

This product conforms to new cord colors.
Los colores de los cables de este producto se
conforman con un nuevo código de colores.
As cores dos fios deste produto seguem um novo
padrão de cores.

Printed in Thailand

<CRD3952-A/N> CS

<KNNZX> <04J00000>